ETC ArcSystem Pro D4 Series Manual de usuario

ArcSystem Pro D4 Series Drivers

Installation Guide

Part Number: 7490M2170 Rev: C

Released: 2020-12

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Document Conventions 1

Help from ETC Technical Services 2

Safety 3

System Overview 4

D1 Series, D2 Series, and D4 Series Drivers 5

TX1 Transmitter 6

ArcMesh 7

ArcMesh Specifications 8

Emergency System Overview 8

Before You Begin Installation 10

Power Disconnect Device 10

Site Survey for Wireless Installations 10

Installation Requirements 10

D4 ConstantVoltage Drivers and Voltage Drop 11

One-Cell Luminaire Installation 12

Preparing the Ceiling for Recessed Luminaires 12

Installing One-Cell Recessed Luminaires 14

Installing One-Cell Yoke-Mounted Luminaires 14

D4 Series Wall-Mount Driver Installation 15

Electrical and Wiring Specification 15

Wire and Terminal Specifications 16

Prepare for Wall-Mount Installation 17

Wall-Mounting Supplies 17

Wall-Mount the Driver 17

Terminate Wiring 18

Wall-Mount Driver Wiring Overview 18

Power Input Wiring 20

Output Wiring 22

DMX In and DMX Thru 23

D4 Driver 150 Current Configuration 26

D4 Series Rack-Mount Driver Installation 27

Electrical and Wiring Specification 27

Prepare for Rack-Mount Installation 27

Rack-Mounting Safety 28

Terminate Wiring 28

Power Input Wiring 29

Output Wiring to Fixture 29

Bridging Output Channels 29

DMX In and DMX Thru 30

Emergency System One-Cell Installation 31

Emergency Driver Power Input Wiring 31

Wall-Mount Emergency Drivers 32

Wall-Mount Emergency Driver Installation 34

Rack-Mount Emergency Drivers 38

D4 Emergency Driver 150 Current Configuration 40

Final Installation and Operation 41

Power Up Procedure 41

Updating the Luminaire Firmware 41

Wireless ArcMesh Luminaires 41

RDM Luminaires 41

Commissioning a Wireless ArcSystem 42

DMX System Control 42

RDM Values 43

Maintenance 45

Emergency Operation and Test 46

ii D4 Series Drivers Installation Guide

Troubleshooting 47

LED Indicators 47

Overload Protection 48

Bridge D4 Series Constant Voltage Driver Output

Channels 49

Voltage Drop 51

Wall-Mount Bridging Kits 51

Rack-Mount Bridging Kits 51

Output Channel Control Switches 52

Example Bridge Configurations 55

Bridging Procedure 58

Compliance 59

FCCCompliance 59

EUDeclaration of Conformity 59

Table of Contents iii

iv D4 Series Drivers Installation Guide

Introduction 1

Introduction

Congratulations on your purchase of ArcSystem products. ArcSystem is a family of overhead LED

products designed for installations where dimming, light quality, and ease of installation are

absolutely essential. With ArcSystem, you will experience perfectly smooth dimming from 100%

down to absolute zero. ArcSystem luminaires come in a variety of form factors, beam angles,

and color-temperature options, all with high-efficiency optics and an outstanding quality of light

ideal for any application.

ArcSystem products with ArcMesh can be controlled using wired DMX or the wireless ArcMesh

protocol. ArcSystem products without ArcMesh can be configured for RDMcontrol. This manual

provides step by step instruction on the installation of ArcSystem Pro One-Cell luminaires, D4

Series Drivers, and full system integration. For information on installing ArcSystem Pro D1 and

D2 Series Drivers, see

the ArcSystem D1 and D2 Series Drivers Installation Guide

etcconnect.com/ArcSystem. For information on ArcSystem Pro Multi-Cell luminaires, see the

ArcSystem Pro Installation Manual

and the

ArcSystem Pro Multi-Cell RDMInstallation Guide

etcconnect.com/ArcSystem.

All ETCmanuals are available for download free of charge at etcconnect.com.

Document Conventions

This document uses the following conventions to draw your attention to important information.

Note:

Notes are helpful hints and information that is supplemental to the main text.

CAUTION:

A Caution statement indicates situations where there may be

undefined or unwanted consequences of an action, potential for data loss or

an equipment problem.

WARNING: A Warning statement indicates situations where damage may

occur, people may be harmed, or there are serious or dangerous

consequences of an action.

WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates

situations where there is a risk of electric shock.

All ETC documents are available for free download from our website: etcconnect.com.

Please email comments about this manual to: TechComm@etcconnect.com.

2 D4 Series Drivers Installation Guide

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this document, try the ETC

support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none

of these resources are sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices outside of normal business

hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

Americas United Kingdom

ETC, Inc. ETC Ltd

Technical Services Department Technical Services Department

3031 Pleasant View Road 26-28 Victoria Industrial Estate

Middleton, WI 53562 Victoria Road,

800-775-4382 (USA, toll-free) London W3 6UU England

+1-608 831-4116 +44 (0)20 8896 1000

service@etcconnect.com techservltd@etcconnect.com

Asia Germany

ETCAsia ETC GmbH

Technical Services Department Technical Services Department

Room 1801, 18/F Ohmstrasse 3

Tower 1, Phase 1 Enterprise Square 83607 Holzkirchen, Germany

9 Sheung Yuet Road +49 (80 24) 47 00-0

Kowloon Bay, Kowloon, Hong Kong techserv-germany@etcconnect.com

+852 2799 1220

techserv-asia@etcconnect.com

France

ETC France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservltd@etcconnect.com

Introduction 3

Safety

ArcSystem products are intended for professional use only. Read the entire manual before

using this equipment.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it will not readily be

subjected to tampering by unauthorized personnel.

•

The use of accessory equipment not recommended by the manufacturer may cause an

unsafe condition.

•

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

4 D4 Series Drivers Installation Guide

System Overview

ArcSystem Pro One-Cell luminaires require an external driver.

Models are available to meet your installation requirements. This guide covers the products

listed below.

ArcSystem Pro One-Cell

•

external D1 Series or D4 Series driver

required

•

ideal for short/medium throw

•

25 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount

with two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Small

•

external D1 Series or D4 Series driver

required

•

ideal for short/medium throw

•

25 W full load power consumption

•

adjustable version recessed/flush mount with

single-axis tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 19°, 24°, 37°, 60°

ArcSystem Pro One-Cell High Output

•

external D1 HO driver required

•

ideal for long throw

•

100 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount

with two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Micro

•

external D2 driver required

•

ideal for short/medium throw

•

20 W full load power consumption

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

yoke-mount version with single-axis tilt

•

beam angle options: 19°, 24°, 37°, 60°

Note:

The ArcSystem Pro One-Cell Micro is not available in 5000 K or Fade to Warm

variants. The ArcSystem Pro One-Cell High Output is not available in 3500K, 4000K,

5000K, or Fade to Warm variants.

ArcSystem Pro multi-cell luminaires are covered in the

ArcSystem Pro Multi-Cell

RDMInstallation Guide

and

ArcSystem Pro Installation Manual

. All ETCmanuals are available

for download free of charge at etcconnect.com.

Otros manuales para ArcSystem Pro D4 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de ETC

ETC

ETC Echoflex ELED1-BUN Manual de usuario

ETC

ETC ArcSystem Navis 100 Manual de usuario

ETC

ETC Foundation Rigging Controller Manual de instalación y operación

ETC

ETC echoflex ElahoTouch Manual de usuario

ETC

ETC Echoflex ELED1H Manual de usuario

ETC

ETC EA07 Manual de usuario

ETC

ETC DMX DEBC-1 Manual de usuario

ETC

ETC Echoflex ELED2 Manual de usuario

ETC

ETC Echoflex ELED2-BU Manual de usuario

ETC

ETC ION Manual de usuario

ETC

ETC Element Manual de usuario

ETC

ETC echoflex ELEDR Manual de usuario

ETC

ETC ALiEn2 Manual de usuario

ETC

ETC Unison Foundry Relay Controller Manual de usuario

ETC

ETC QuickTouch Preset Manual de usuario

ETC

ETC echoflex ELEDR-RH Manual de usuario

ETC

ETC Expression Guía de configuración

ETC

ETC echoflex ELED1 Manual de usuario

ETC

ETC Paradigm P-TS7-PE Manual de usuario

ETC

ETC EA5K3 Manual de usuario

ETC

ETC echoflex ELED1 Manual de usuario

ETC

ETC echoflex ELED2-BCL Manual de usuario

ETC

ETC P-ACP Hoja de instrucciones

ETC

ETC Unison Aero Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario