ETC Unison Aero Manual de usuario
ETC Installation Guide
Unison Aero®Micro Relay Controller
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA
Tel +608 831 4116
Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK
Tel +44 (0)20 8896 1000
Fax +44 (0)20 8896 2000
Rome, IT
Via Pieve Torina, 48, 00156 Rome, Italy
Tel +39 (06) 32 111 683
Fax +44 (0)20 8752 8486
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany
Tel +49 (80 24) 47 00-0
Fax +49 (80 24) 47 00-3 00
Hong Kong
Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong
Tel +852 2799 1220
Service:
(Americas) service@etcconnect.com
(UK) service@etceurope.com
(DE) techserv-hoki@etcconnect.com
(Asia) [email protected]
Web:
www.etcconnect.com
Copyright © 2014 ETC. All Rights Reserved.
Product information and specifications subject to change.
7189M2107
Rev C
Released 2014-09
ETC intends this document to be provided in its entirety.
Overview
The Aero Micro Relay Controller (UAMR) controls lighting loads when a
received input from a linked sensor or switch is changed.
The UAMR controls loads based on the following:
• switch actions from an Aero SmartClick Switch Station
• ambient light levels as monitored by an Aero Light Sensor
• occupancy state as monitored by an Aero Occupancy Sensor
• input from another Aero device
ETC Installation Guide
Micro Relay Controller
Micro Relay Controller Install Guide Page 2 of 4
Placement and Radio Range
The UAMR is intended for use with Aero sensors and stations. Consideration
should be made for locating the controllers based on the construction materials
and furniture that may disrupt transmissions. Fire doors, elevator shafts,
stairwells, storage areas and any large metal objects can create radio shadows
and disrupt wireless transmissions.
It is recommended that stations and sensors be placed with in 50 feet (15m) of
the UAMR controller for optimal performance.
Typical Radio Range
Material Range - typical
Line of sight 100 feet (30m) corridors
Line of sight 330 feet (100m) open halls
Plasterboard 100 feet (30m) through 5
walls
Brick 65 feet (20m) through 3 walls
Concrete 65 feet (20m) through 3 walls
FerroConcrete 33 feet (10m)
Ceiling 1 ceiling
Signal Loss
Material Attenuation
Wood/Plaster/Glass 0-10%
Brick/MDF 5-35%
Metal 90-100%
ETC Installation Guide
Power Series
Page 3 of 4 Micro Relay Controller Install Guide
Installation
The UAMR is mounted directly to an electrical junction box or panel at the load
or before the load in the circuit.
Step 1: Locate the circuit breaker panel and turn off the power to the circuit.
Step 2: Remove face plates and other hardware from the junction box, gaining
access to the high voltage wiring.
Step 3: The UAMR mounts inside the junction box or panel.
Step 4: The UAMR controller is provided with a wire harness that serves
120 - 277 VAC power requirements. Refer to the wiring diagram above
to connect power to the controller.
a: Connect the black wire to the line input feed wire.
b: Connect the white wire to the incoming Neutral wire.
c: Connect the red (relay output) to the lighting load.
Step 5: Replace the junction box face plate and hardware.
Note:
If the circuit will have an additional hard wired switch, wire the
UAMR in series before the switch.
WARNING:
Risk of electric shock! The UAMR utilizes high voltage and
should only be installed by a qualified installer or electrician.
Follow all local codes for installation. Before terminating the
AC power wiring verify the main breaker is in the off position
and follow the proper lockout/tag out procedures per NFPA
Standard 70E.
WARNING:
For indoor use only! Must install in an electrical junction box
or wire way.
CAUTION:
The UAMR has an orange external antenna that extends off
one end of the unit. Do not cut, cap, or connect this wire.
Note:
Follow all local code requirements for terminating wiring.
Notice the harness wires on the controller unit are pre-stripped
for your installation convenience.
O
RANGE
(
ANTENNA
)
W
HITE
(
NEUTRAL
)
G
REEN
(
GROUND
)
B
LACK
(120 - 277VAC)
WIRELESS
TO
OTHER
DEVICES
UNISON AERO MICRO
RELAY CONTROLLER
(UAMR)
L
OAD
R
ED
(
RELAY
OUTPUT
)
ETC Installation Guide
Micro Relay Controller
Micro Relay Controller Install Guide Page 4 of 4
Power Up and Test
For detailed programming and configuration information, please reference the
Unison Aero 902 MHz User Programming Guide. ETC documentation is
available for free download at www.etcconnect.com.
Step 1: Restore power to the circuit.
Step 2: Test the circuit by linking a Unison Aero Wireless Switch.
a: Within radio range of the controller, press the toggle switch up (On) three
times consecutively.
b: Press the toggle switch down (Off) three times consecutively.
c: Press the toggle switch up again, three times consecutively.
Step 3: Test the controller response.
a: Press the toggle switch “Off” once. The controlled lighting should respond
by turning off.
b: Press the toggle switch “On” once. The controlled lighting should respond
by turning on.
Note:
The linking method described in “Step 2” will learn the Unison
Aero Wireless Switch to any controllers that are within radio
range that do not already have stations linked to them.
Contains FCC ID: SZV-TCM320U
The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(i.) this device may not cause harmful interference and
(ii.) this device must accept any interference received, including
interference that may cause undesired operation.
Contains IC: 5713A-TCM320U
Tabla de contenidos
Otros manuales de Controladores de ETC
ETC
ETC echoflex ELED2-BCL Manual de usuario
ETC
ETC QuickTouch Preset Manual de usuario
ETC
ETC Unison Mosaic Manual de usuario
ETC
ETC Echoflex ELED3 Manual de usuario
ETC
ETC Element Manual de usuario
ETC
ETC EA5K3 Manual de usuario
ETC
ETC Paradigm P-TS7-PE Manual de usuario
ETC
ETC Echoflex ELED3 Manual de usuario
ETC
ETC EA07 Manual de usuario
ETC
ETC echoflex ELED1 Manual de usuario
ETC
ETC ION Manual de usuario
ETC
ETC QuickTouch+ Mk2 Manual de usuario
ETC
ETC EchoDIN Power Control Processor Mk2 Manual de usuario
ETC
ETC Echoflex Elaho Inspire Station Instrucciones de funcionamiento
ETC
ETC Echoflex ELED2-BU Manual de usuario
ETC
ETC Echoflex ELED1H Manual de usuario
ETC
ETC QuickTouch Manual de usuario
ETC
ETC ArcSystem Navis 100 Manual de usuario
ETC
ETC echoflex ELEDR-RH Manual de usuario
ETC
ETC echoflex ELEDR Manual de usuario
