Endress+Hauser Proline 300 Especificaciones técnicas
Products Solutions Services
Brief Operating Instructions
Proline 300
Modbus RS485
Transmitter with thermal mass flow sensor
These instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Brief Operating Instructions part 2 of 2: Transmitter
Contain information about the transmitter.
Brief Operating Instructions part 1 of 2: Sensor → 3
KA01445D/06/EN/02.21
71528708
2021-07-01
Proline 300 Modbus RS485
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
Proline 300 Modbus RS485 Brief Operating Instructions for flowmeter
Endress+Hauser 3
Brief Operating Instructions for flowmeter
The device consists of a transmitter and a sensor.
The process of commissioning these two components is described in two separate manuals
that together form the Brief Operating Instructions for the flowmeter:
• Brief Operating Instructions Part 1: Sensor
• Brief Operating Instructions Part 2: Transmitter
Please refer to both parts of the Brief Operating Instructions when commissioning the device,
as the contents of the manuals complement one another:
Brief Operating Instructions Part 1: Sensor
The Sensor Brief Operating Instructions are aimed at specialists with responsibility for
installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation
Brief Operating Instructions Part 2: Transmitter
The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for
commissioning, configuring and parameterizing the measuring device (until the first
measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information
Additional device documentation
These Brief Operating Instructions are Brief Operating Instructions Part 2:
Transmitter.
The "Brief Operating Instructions Part 1: Sensor" are available via:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App
Detailed information about the device can be found in the Operating Instructions and the
other documentation:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App
Table of contents Proline 300 Modbus RS485
4 Endress+Hauser
Table of contents
1 About this document .............................................................. 5
1.1 Symbols used ......................................................................... 5
2 Safety instructions ................................................................ 7
2.1 Requirements for the personnel ............................................................ 7
2.2 Designated use ........................................................................ 7
2.3 Occupational safety ..................................................................... 8
2.4 Operational safety ......................................................................8
2.5 Product safety ......................................................................... 9
2.6 IT security ............................................................................ 9
2.7 Device-specific IT security ................................................................ 9
3 Product description ............................................................... 9
4 Installation ...................................................................... 11
4.1 Turning the transmitter housing .......................................................... 11
4.2 Turning the display module .............................................................. 13
4.3 Transmitter post-installation check ........................................................ 13
5 Electrical connection ............................................................ 14
5.1 Electrical safety .......................................................................14
5.2 Connection conditions .................................................................. 14
5.3 Connecting the measuring device ......................................................... 17
5.4 Ensuring potential equalization ........................................................... 21
5.5 Hardware settings ..................................................................... 21
5.6 Ensuring the degree of protection ......................................................... 23
5.7 Post-connection check ..................................................................23
6 Operation options ............................................................... 25
6.1 Overview of operation options ............................................................ 25
6.2 Structure and function of the operating menu ................................................ 26
6.3 Access to the operating menu via the local display ............................................. 27
6.4 Access to the operating menu via the operating tool ............................................ 30
6.5 Access to the operating menu via the Web server .............................................. 30
7 System integration .............................................................. 30
8 Commissioning .................................................................. 31
8.1 Function check ....................................................................... 31
8.2 Setting the operating language ........................................................... 31
8.3 Configuring the measuring device ......................................................... 32
8.4 Protecting settings from unauthorized access ................................................. 32
9 Diagnostic information .......................................................... 33
Proline 300 Modbus RS485 About this document
Endress+Hauser 5
1 About this document
1.1 Symbols used
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Symbols for certain types of information
Symbol Meaning Symbol Meaning
Permitted
Procedures, processes or actions that
are permitted.
Preferred
Procedures, processes or actions that
are preferred.
Forbidden
Procedures, processes or actions that
are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
1.
,
2.
,
3.
… Series of steps
Result of a step Visual inspection
1.1.3 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.
About this document Proline 300 Modbus RS485
6 Endress+Hauser
Symbol Meaning
Protective Earth (PE)
A terminal which must be connected to ground prior to establishing any other connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
1.1.4 Communication symbols
Symbol Meaning Symbol Meaning
Wireless Local Area Network
(WLAN)
Communication via a wireless, local
network.
Bluetooth
Wireless data transmission between
devices over a short distance.
Promag 800
Cellular radio
Bidirectional data exchange via cellular
network.
LED
Light emitting diode is off.
LED
Light emitting diode is on.
LED
Light emitting diode is flashing.
1.1.5 Tool symbols
Symbol Meaning Symbol Meaning
Torx screwdriver Flat blade screwdriver
Cross-head screwdriver Allen key
Open-ended wrench
1.1.6 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
Proline 300 Modbus RS485 Safety instructions
Endress+Hauser 7
2 Safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣Follow instructions and comply with basic conditions.
2.2 Designated use
Application and media
The measuring device described in this manual is intended only for the flow measurement of
gases.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas or where there is an increased risk due to
process pressure, are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.
LWARNING
Danger of breakage due to corrosive or abrasive fluids and ambient conditions!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.
Safety instructions Proline 300 Modbus RS485
8 Endress+Hauser
NOTICE
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
LWARNING
Injury from sensor being ejected!
‣The sensor gland should be opened only when in an unpressurized state.
LWARNING
Risk of injury if the process connection and gland of the sensing element are opened
under pressure.
‣The process connection and sensor gland should be opened only when in an unpressurized
state.
NOTICE
Penetration of dust and moisture when the transmitter housing is opened.
‣Only open the transmitter housing briefly, ensuring that no dust or moisture enters the
housing.
Residual risks
LWARNING
If the temperature of the media or electronics unit is high or low, this may cause the
surfaces of the device to become hot or cold. This poses a risk of burns or frostbite!
‣In the case of hot or cold medium temperatures, install appropriate protection against
contact.
2.3 Occupational safety
When working on and with the device:
‣Wear the required personal protective equipment as per national regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣Due to the increased risk of electric shock, wear suitable gloves.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Proline 300 Modbus RS485 Product description
Endress+Hauser 9
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.
2.7 Device-specific IT security
The device offers a range of specific functions to support protective measures on the operator's
side. These functions can be configured by the user and guarantee greater in-operation safety
if used correctly.
For detailed information on device-specific IT security, see the Operating Instructions for
the device.
2.7.1 Access via service interface (CDI-RJ45)
The device can be connected to a network via the service interface (CDI-RJ45). Device-specific
functions guarantee the secure operation of the device in a network.
The use of relevant industrial standards and guidelines that have been defined by national
and international safety committees, such as IEC/ISA62443 or the IEEE, is recommended.
This includes organizational security measures such as the assignment of access authorization
as well as technical measures such as network segmentation.
Transmitters with an Ex de approval may not be connected via the service interface (CDI-
RJ45)!
Order code for "Approval", options (Ex de): BB, C2, GB, MB, NB
3 Product description
The device consists of a Proline 300 transmitter and a Proline t-mass
thermal mass flowmeter sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
Product description Proline 300 Modbus RS485
10 Endress+Hauser
5
4
Nicht unter
Spannung öffnen
Do not open when
energized
Ne pas ouvrir
sous tension
Power
I/O
N
i
c
ht
u
n
t
e
r
a
r
e
ö
f
f
n
e
n
D
i
s
p
l
a
y
+E
ESC
–
123
A0029586
1 Connection compartment cover
2 Display module
3 Transmitter housing
4 Electronics compartment cover
5 Sensor
Use of the device with the remote display and operating module DKX001 → 21.
For detailed information on the product description, see the Operating Instructions for
the device
Otros manuales para Proline 300
3
Tabla de contenidos
Otros manuales de Transmisor de Endress+Hauser
Endress+Hauser
Endress+Hauser tmt142 Instrucciones de instalación
Endress+Hauser
Endress+Hauser CM14 Manual de usuario
Endress+Hauser
Endress+Hauser Proline 300 PROFIBUS PA Manual de usuario
Endress+Hauser
Endress+Hauser Liquiline M CM42 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT80 Manual de usuario
Endress+Hauser
Endress+Hauser Cerabar S PMP71 Manual de usuario
Endress+Hauser
Endress+Hauser Proline 500 PROFIBUS PA Especificaciones técnicas
Endress+Hauser
Endress+Hauser RMA42 Especificaciones técnicas
Endress+Hauser
Endress+Hauser CM14 Manual de usuario
Endress+Hauser
Endress+Hauser Cerabar S PMC71 Manual
Endress+Hauser
Endress+Hauser Flowmeter Proline 200 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Commubox FXA291 Manual de usuario
Endress+Hauser
Endress+Hauser Mycom CLM 152 Manual de usuario
Endress+Hauser
Endress+Hauser Flowmeter Proline 300 Especificaciones técnicas
Endress+Hauser
Endress+Hauser iTEMP TMT162 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Proline Prosonic Flow 93 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT85 Manual de usuario
Endress+Hauser
Endress+Hauser Liquiline Compact CM82 Manual de usuario
Endress+Hauser
Endress+Hauser iTEMP TMT82 Especificaciones técnicas
Endress+Hauser
Endress+Hauser Cerabar S PMP71 Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
