Endress+Hauser ITEMP TMT82 Especificaciones técnicas

Products Solutions Services

Brief Operating Instructions

iTEMP TMT82

2-channel temperature transmitter

These instructions are Brief Operating Instructions; they do

not replace the Operating Instructions included in the scope of

supply.

Detailed information can be found in the Operating

Instructions and the additional documentation.

Available for all device versions via:

• Internet: www.endress.com/deviceviewer

• Smart phone/tablet: Endress+Hauser Operations App

KA01095T/09/EN/19.21

71502237

2021-01-15

iTEMP TMT82

2 Endress+Hauser

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

iTEMP TMT82 Table of contents

Endress+Hauser 3

Table of contents

1 Important document information ................................................. 3

1.1 Safety Instructions (XA) ................................................................. 3

1.2 Functional safety ...................................................................... 4

1.3 Symbols ............................................................................. 4

2 Basic safety instructions .......................................................... 5

2.1 Requirements for the personnel ............................................................ 5

2.2 Intended use .......................................................................... 5

2.3 Operational safety ......................................................................5

3 Incoming acceptance and product identification ................................... 6

3.1 Incoming acceptance .................................................................... 6

3.2 Product identification ................................................................... 6

3.3 Name and address of manufacturer ......................................................... 8

3.4 Scope of delivery ....................................................................... 8

3.5 Certificates and approvals ................................................................ 9

4 Mounting ......................................................................... 9

4.1 Mounting requirements ................................................................. 9

4.2 Mounting ........................................................................... 10

4.3 Post-mounting check .................................................................. 15

5 Electrical connection ............................................................ 16

5.1 Connection conditions .................................................................. 16

5.2 Quick wiring guide .................................................................... 17

5.3 Connecting the sensor cables ............................................................. 20

5.4 Connecting the transmitter .............................................................. 22

5.5 Special connection instructions ........................................................... 22

5.6 Ensuring the degree of protection ......................................................... 23

5.7 Post-connection check ..................................................................24

6 Operating options ............................................................... 25

6.1 Measured value display and operating elements ............................................... 25

6.2 Configuration of transmitter and HART® protocol .............................................. 27

7 Commissioning .................................................................. 27

1 Important document information

1.1 Safety Instructions (XA)

When using in hazardous areas, compliance with national regulations is mandatory. Separate

Ex-specific documentation is provided for measuring systems that are used in hazardous

areas. This documentation is an integral part of these Operating Instructions. The installation

specifications, connection data and safety instructions it contains must be strictly observed!

Make sure that you use the right Ex-specific documentation for the right device with approval

for use in hazardous areas! The number of the specific Ex documentation (XA...) is provided

on the nameplate. If the two numbers (on the Ex documentation and the nameplate) are

identical, then you may use this Ex-specific documentation.

Important document information iTEMP TMT82

4 Endress+Hauser

1.2 Functional safety

Please refer to Safety Manual SD01172T/09 for the use of approved devices in protective

systems according to IEC 61508.

1.3 Symbols

1.3.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

1.3.2 Tool symbols

Symbol Meaning

A0011220

Flat blade screwdriver

A0011219

Phillips head screwdriver

A0011221

Allen key

A0011222

Open-ended wrench

1.3.3 Registered trademark

HART®

Registered trademark of the FieldComm Group, Austin, Texas, USA

iTEMP TMT82 Basic safety instructions

Endress+Hauser 5

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel for installation, commissioning, diagnostics and maintenance must fulfill the

following requirements:

‣Trained, qualified specialists must have a relevant qualification for this specific function

and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before beginning work, the specialist staff must have read and understood the instructions

in the Operating Instructions and supplementary documentation as well as in the

certificates (depending on the application)

‣Following instructions and basic conditions

The operating personnel must fulfill the following requirements:

‣Being instructed and authorized according to the requirements of the task by the facility's

owner-operator

‣Following the instructions in these Operating Instructions

2.2 Intended use

The device is a universal and user-configurable temperature transmitter with either one or

two sensor inputs for for a resistance thermometer (RTD), thermocouples (TC), resistance and

voltage transmitters. The head transmitter version of the device is intended for mounting in a

terminal head (flat face) as per DIN EN 50446. It is also possible to mount the device on a DIN

rail using the optional DIN rail clip. The device is also optionally available in a version suitable

for DIN rail mounting as per IEC 60715 (TH35).

If the equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Operational safety

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous

area (e.g. explosion protection or safety equipment):

‣Based on the technical data on the nameplate, check whether the ordered device is

permitted for the intended use in the hazardous area. The nameplate can be found on the

side of the transmitter housing.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

Incoming acceptance and product identification iTEMP TMT82

6 Endress+Hauser

Electromagnetic compatibility

The measuring system complies with the general safety requirements as per EN 61010-1, the

EMC requirements as per the IEC/EN 61326 series and the NAMUR recommendations NE 21.

NOTICE

‣The device must only be powered by a power unit that operates using an energy-limited

electric circuit according to UL/EN/IEC 61010-1, chapter 9.4 and requirements of table 18.

3 Incoming acceptance and product identification

3.1 Incoming acceptance

1. Unpack the temperature transmitter carefully. Is the packaging or content damaged?

 Damaged components may not be installed as the manufacturer can otherwise not

guarantee compliance with the original safety requirements or the material

resistance, and can therefore not be held responsible for any resulting damage.

2. Is the delivery complete or is anything missing? Check the scope of delivery against your

order.

3. Does the nameplate match the ordering information on the delivery note?

4. Are the technical documentation and all other necessary documents provided? If

applicable: are the Safety Instructions (e.g. XA) for hazardous areas provided?

If one of these conditions is not satisfied, contact your Endress+Hauser Sales Center.

3.2 Product identification

The following options are available for identification of the device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

• Enter the serial number from the nameplate in the W@M Device Viewer

(www.endress.com/deviceviewer): All data relating to the device and an overview of the

Technical Documentation supplied with the device are displayed.

• Enter the serial number on the nameplate into the Endress+Hauser Operations App or scan

the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations App:

all the information about the device and the technical documentation pertaining to the

device is displayed.

3.2.1 Nameplate

The right device?

Compare and check the data on the nameplate of the device against the requirements of the

measuring point:

iTEMP TMT82 Incoming acceptance and product identification

Endress+Hauser 7

11-42V 012345678910

xx.yy.zz

TMT82- XXXXX/XX

iTEMP

Made in Germany 201x

D-87484 Nesselwang

Ser.no.:

FW:

Input:

12345678ABCDEFGH

Dev.Rev: x

Ext. ord. cd.:

XXXXXXXXXXXXX#

A0014561

 1 Nameplate of the head transmitter (example, Ex version)

1 Power supply, current consumption and extended order code

2 Serial number, device revision, firmware version and hardware version

3 Data Matrix 2D code

4 2 lines for the TAG name

5 Approval in hazardous area with number of the relevant Ex documentation (XA...)

6 Approvals with symbols

7 Order code and manufacturer ID

0044

iTEMP®TMT82

Made in Germany 2012 D-87484 Nesselwang

TAGXXXXXXXXXXX

Order code: TMT82-xxx/xx

Ext. ord. cd.: XXXXXXXXXXX

Ser. no.: XXXXXXXXX

Input: 12-42 V

Current cunsum.: 23,0 mA

EH 08.001X

II3G Ex nA II T6/T5/T4 Ta= -40 ...+ 55/70/85°C

II3G Ex nL IIC T6/T5/T4 Ta= -40 ... +55/70/85°C

Install per XA0xxxxT/09/a3/xx.xx

A0017924

 2 Nameplate of DIN rail transmitter (example, Ex version)

1 Product name and manufacturer ID

2 Order code, extended order code and serial number, DataMatrix 2D code, FCC-ID (if applicable)

3 Power supply and current consumption, output

4 Approval in hazardous area with number of the relevant Ex documentation (XA...)

5 Fieldbus communication logo

6 Firmware version and device revision

7 Approval logos

7 2 lines for the TAG name

Incoming acceptance and product identification iTEMP TMT82

8 Endress+Hauser

D-87484 Nesselwang

202x

A0042425

 3 Nameplate of the field mount housing version (example, Ex version)

1 Order code, extended order code, serial number and manufacturer ID

2 Power supply and current consumption, IP-code and ambient temperature, firmware, hardware and

device revision

3 Approval in hazardous area with number of the relevant Ex documentation (XA....) and ambient

temperature range

4 Approval logos and data matrix 2D code

5 2 lines for the TAG name

3.3 Name and address of manufacturer

Name of manufacturer: Endress+Hauser Wetzer GmbH + Co. KG

Address of manufacturer: Obere Wank 1, D-87484 Nesselwang or www.endress.com

Address of manufacturing plant: See nameplate

3.4 Scope of delivery

The scope of delivery of the device comprises:

• Temperature transmitter

• Mounting material (head transmitter), optional

• Hard copy of multi-language Brief Operating Instructions

• Functional Safety Manual (SIL mode)

• Additional documentation for devices which are suitable for use in the hazardous area

(ATEX, FM, CSA), such as Safety Instructions (XA)

iTEMP TMT82 Mounting

Endress+Hauser 9

3.5 Certificates and approvals

The device left the factory in a safe operating condition. The device complies with the

requirements of the standards EN 61010-1 "Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use" and with the EMC requirements as per the

IEC/EN 61326 series.

3.5.1 CE/EAC mark, Declaration of Conformity

The device meets the legal requirements of the EU/EEU guidelines. The manufacturer

confirms that the device is compliant with the relevant guidelines by applying the CE/EAC

mark.

3.5.2 HART® protocol certification

The temperature transmitter is registered by the HART® FieldComm Group. The device meets

the requirements of the HART® Communication Protocol Specifications, Revision 7 (HCF 7.6).

3.5.3 Functional safety

The two device versions (head transmitter/DIN rail device) are optionally available for use in

safety systems as per IEC 61508.

• SIL 2: Hardware version

• SIL 3: Software version

4 Mounting

4.1 Mounting requirements

4.1.1 Mounting location

• Head transmitter:

• In the terminal head, flat face, as per DIN EN 50446, direct mounting on insert with cable

entry (middle hole 7 mm)

• In the field housing, separated from the process

• In the field mount housing with separate terminal compartment, if stable sensors are

used, the device can be fitted directly on the assembly, otherwise it has to be mounted

separated from the process

• With clip on DIN rail as per IEC 60715, TH35

• DIN rail transmitter:

In DIN rail housing on DIN rail as per IEC 60715, TH35

Mounting iTEMP TMT82

10 Endress+Hauser

4.1.2 Important ambient conditions

• Ambient temperature:

• –40 to +85 °C (–40 to +185 °F), for hazardous areas see Ex documentation

• –50 to +85 °C (–58 to +185 °F), for hazardous areas see Ex documentation; Product

Configurator order code for "Test, certificate, declaration", option "JM" 1)

• –52 to +85 °C (–62 to +185 °F), for hazardous areas see Ex documentation, Product

Configurator order code for "Test, certificate, declaration", option "JN" 1)

• Head transmitter, field mount housing with separate terminal compartment incl. display:

–30 to +85 °C (–22 to +185 °F). At temperatures < –20 °C (–4 °F) the display may react

slowly, Product Configurator, order code for "Field housing", option "R" and "S"

• SIL Mode: –40 to +70 °C (–40 to +158 °F)

• Head transmitter in accordance with climate class C1, DIN rail transmitter in accordance

with B2 as per EN 60654-1

• Condensation as per IEC 60068-2-33 permitted for head transmitter, not permitted for DIN

rail transmitter

• Max. rel. humidity: 95% as per IEC 60068-2-30

• Degree of protection:

• Head transmitter with screw terminals: IP 00, with spring terminals: IP 30. In installed

state, depends on the terminal head or field housing used.

• When installing in field housing TA30x: IP 66/68 (NEMA Type 4x encl.)

• When installing in field mount housing with separate terminal compartment: IP 67,

NEMA Type 4x

• DIN rail device: IP 20

NOTICE

‣When using in hazardous areas, the limit values of the certificates and approvals must be

observed.

4.2 Mounting

A Phillips head screwdriver is required to mount the head transmitter.

NOTICE

Do not overtighten the mounting screws as this could damage the head transmitter.

‣Maximum torque = 1 Nm (¾ pound-feet).

1) If the temperature is below –40 °C (–40 °F), increased failure rates are likely.

Otros manuales para iTEMP TMT82

Tabla de contenidos

Otros manuales de Transmisor de Endress+Hauser

Endress+Hauser

Endress+Hauser Liquisys M CLM 223 Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT80 Manual de usuario

Endress+Hauser

Endress+Hauser easytemp TSM 470 G Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP Pt TMT180 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 PROFIBUS PA Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar M PMD55 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Omnigrad TMT146 Manual de usuario

Endress+Hauser

Endress+Hauser Flowmeter Proline 300 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 93 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar PMC71B Manual de usuario

Endress+Hauser

Endress+Hauser Mycom S CPM 153 Manual de usuario

Endress+Hauser

Endress+Hauser iTEMP TMT82 Manual de usuario

Endress+Hauser

Endress+Hauser Levelflex M FMP41C Manual de usuario

Endress+Hauser

Endress+Hauser RMA42 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquisys M CUM 223 Manual de usuario

Endress+Hauser

Endress+Hauser tmt142 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU95 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 digital Modbus RS485 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Cerabar S PMC71 Manual de usuario

Endress+Hauser

Endress+Hauser TMD1000 Manual de usuario

Endress+Hauser

Endress+Hauser Liquisys M CPM253 Manual de usuario

Endress+Hauser

Endress+Hauser Proline 500 digital PROFIBUS DP Especificaciones técnicas

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Endress+Hauser iTEMP TMT82 Especificaciones técnicas

Manuales populares de Transmisor de otras marcas