Endress+Hauser Smartec CLD18 Manual de usuario

Products Solutions Services

Operating Instructions

Smartec CLD18

Conductivity measuring system

BA01149C/07/EN/06.17

71393688

AUTHORIZED DISTRIBUTOR:

InstrumentsAndControl.com

Houston, Texas USA

[email protected]

281-609-7170

Smartec CLD18 Table of contents

Endress+Hauser 3

Table of contents

1 Document information ......... 4

1.1 Warnings ........................... 4

1.2 Symbols used ........................ 4

1.3 Symbols on device .................... 5

2 Basic safety instructions ....... 5

2.1 Requirements for the personnel ........ 5

2.2 Designated use ...................... 5

2.3 Occupational safety .................. 5

2.4 Operational safety ................... 7

2.5 Product safety ....................... 7

2.6 IT security .......................... 7

3 Product description ............. 8

3.1 Product design ....................... 8

4 Incoming acceptance and

product identification .......... 9

4.1 Incoming acceptance ................. 9

4.2 Product identification ................. 9

4.3 Scope of delivery .................... 10

4.4 Certificates and approvals ............ 11

5 Installation .................... 11

5.1 Installation conditions ............... 11

5.2 Mounting the compact device ......... 17

5.3 Post-installation check ............... 17

6 Electrical connection .......... 17

6.1 Connecting the transmitter ........... 17

6.2 Ensuring the degree of protection ..... 21

6.3 Post-connection check ............... 21

7 Operation options ............. 22

7.1 Overview of operating options ........ 23

7.2 Structure and function of the operating

menu ............................. 24

8 Commissioning ................ 25

8.1 Switching on the measuring device .... 25

8.2 Display settings (Display menu) ....... 25

8.3 Configuring the measuring device ..... 26

8.4 Advanced settings .................. 26

8.5 Calibration (Calibration menu) ........ 31

9 Diagnostics and

troubleshooting ............... 34

9.1 General troubleshooting ............. 34

9.2 Trouble shooting instructions ......... 34

9.3 Pending diagnostic messages ......... 35

10 Maintenance .................. 38

10.1 Maintenance tasks .................. 38

11 Repairs ......................... 39

11.1 General notes ...................... 39

11.2 Return ............................ 39

11.3 Disposal ........................... 39

12 Accessories .................... 40

12.1 Calibration solutions ................ 40

13 Technical data ................. 40

Index ................................. 47

Document information Smartec CLD18

4 Endress+Hauser

1 Document information

1.1 Warnings

Structure of information Meaning

LDANGER

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation will result in a fatal or serious injury.

LWARNING

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the dangerous situation can result in a fatal or serious injury.

LCAUTION

Causes (/consequences)

If necessary, Consequences of non-

compliance (if applicable)

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or more serious injuries.

NOTICE

Cause/situation

If necessary, Consequences of non-

compliance (if applicable)

‣Action/note

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

Smartec CLD18 Basic safety instructions

Endress+Hauser 5

1.3 Symbols on device

Symbol Meaning

Reference to device documentation

2 Basic safety instructions

2.1 Requirements for the personnel

• Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the specified

activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

• Faults at the measuring point may only be rectified by authorized and specially trained

personnel.

Repairs not described in the Operating Instructions provided must be carried out only

directly at the manufacturer's site or by the service organization.

2.2 Designated use

The compact measuring system is used for inductive conductivity measurement in liquids with

medium to high conductivity.

Use of the device for any purpose other than that described, poses a threat to the safety of

people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

NOTICE

Applications outside specifications!

Incorrect measurements, malfunctions and even measuring point failure could result

‣Use the product only in accordance with the specifications.

‣Pay attention to the technical data on the nameplate.

2.3 Occupational safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

Basic safety instructions Smartec CLD18

6 Endress+Hauser

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable European standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

Smartec CLD18 Basic safety instructions

Endress+Hauser 7

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

‣If faults cannot be rectified:

products must be taken out of service and protected against unintentional operation.

2.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested, and

left the factory in a condition in which it is safe to operate. The relevant regulations and

European standards have been observed.

2.6 IT security

We only provide a warranty if the device is installed and used as described in the Operating

Instructions. The device is equipped with security mechanisms to protect it against any

inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide

additional protection for the device and device data transfer must be implemented by the

operators themselves.

Product description Smartec CLD18

8 Endress+Hauser

3 Product description

3.1 Product design

A0019184

 1 Elements

1 Temperature sensor

2 Process connection

3 Leakage bore (offset by 90° in relation to the flow direction)

4 Removable housing cover

5 Window for display

6 Cable glands (M12)

7 Flow opening of sensor

Smartec CLD18 Incoming acceptance and product identification

Endress+Hauser 9

4 Incoming acceptance and product identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.

 Notify the supplier of any damage to the packaging.

Keep the damaged packaging until the issue has been resolved.

2. Verify that the contents are undamaged.

 Notify the supplier of any damage to the delivery contents.

Keep the damaged goods until the issue has been resolved.

3. Check that the delivery is complete and nothing is missing.

 Compare the shipping documents with your order.

4. Pack the product for storage and transportation in such a way that it is protected

against impact and moisture.

 The original packaging offers the best protection.

Make sure to comply with the permitted ambient conditions.

If you have any questions, please contact your supplier or your local Sales Center.

Technical data→  40

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Firmware version

• Ambient and process conditions

• Input and output values

• Measuring range

• Safety information and warnings

• Protection class

‣Compare the information on the nameplate with the order.

Incoming acceptance and product identification Smartec CLD18

10 Endress+Hauser

4.2.2 Product identification

Product page

www.endress.com/CLD18

Interpreting the order code

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Open the product website.

2. At the top of the page, select the link Services.

 An additional sidebar opens up.

3. Select Online Tools followed by Access device specific information.

 An additional window opens.

4. Enter the order code from the nameplate into the search field. Then select Show

details.

 Details of each feature (selected option) of the order code are displayed.

Manufacturer's address

Endress+Hauser Conducta GmbH+Co. KG

Dieselstraße 24

D-70839 Gerlingen

4.3 Scope of delivery

The delivery comprises:

• A Smartec CLD18 measuring system in the version ordered

• Operating Instructions BA01149C/07/EN

Otros manuales para Smartec CLD18

Tabla de contenidos

Otros manuales de Instrumento de medición de Endress+Hauser

Endress+Hauser

Endress+Hauser Prosonic M Series Manual de usuario

Endress+Hauser

Endress+Hauser RIA46 Manual de usuario

Endress+Hauser

Endress+Hauser Cerabar PMP21 Manual de usuario

Endress+Hauser

Endress+Hauser Prosonic S FMU95 Manual de usuario

Endress+Hauser

Endress+Hauser Proline t-mass 65 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar S PMD70 Manual de usuario

Endress+Hauser

Endress+Hauser Tankvision Multi Scan NXA83 Manual de usuario

Endress+Hauser

Endress+Hauser RIA251 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass 200 Instrucciones de instalación

Endress+Hauser

Endress+Hauser PROline promag 23 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar PMD78B Manual de usuario

Endress+Hauser

Endress+Hauser prowirl 70 Manual

Endress+Hauser

Endress+Hauser Micropilot M FMR250 Manual de usuario

Endress+Hauser

Endress+Hauser FQG66 Manual de usuario

Endress+Hauser

Endress+Hauser FHG65 Manual de usuario

Endress+Hauser

Endress+Hauser ria45 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Hart Micropilot FMR60B Especificaciones técnicas

Endress+Hauser

Endress+Hauser Deltabar S PMD70 Especificaciones técnicas

Endress+Hauser

Endress+Hauser Liquiline System CA80TN Especificaciones técnicas

Endress+Hauser

Endress+Hauser Stamosens CSM750 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promass O 300 Manual

Endress+Hauser

Endress+Hauser Flowfit CUA252 Manual de usuario

Endress+Hauser

Endress+Hauser LPGmass Especificaciones técnicas

Endress+Hauser

Endress+Hauser FTL62 Series Instrucciones de uso

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

R&S

R&S ZPH Manual de usuario