Emerson Rosemount 585 Annubar Manual de usuario

Quick Start Guide

00825-0100-4585, Rev AB

June 2016

Rosemount™585 Annubar™Flanged

Assembly

4585_QIG_AB.fm Page 1 Monday, June 20, 2016 5:09 PM

June 2016

Quick Start Guide

NOTICE

This guide provides basic guidelines for Rosemount 585 Annubar Assembly. It does not provide instructions

for configuration, diagnostics, maintenance, service, troubleshooting, Explosion-proof, Flame-Proof, or

intrinsically safe (I.S.) installations. Refer to the Rosemount 585 Reference Manual (document number

00809-0100-4585) for more instruction. This manual is also available electronically on

www.rosemount.com.

If the Rosemount Annubar was ordered assembled to a Rosemount Pressure Transmitter, see the following

Quick Start Guides for information on configuration and hazardous locations certifications:

Rosemount 3051S Series Pressure Transmitter and Rosemount 3051SF Series Flowmeter Quick Start

Guide.

Rosemount 3051S MultiVariable Transmitter and Rosemount 3051SF Series Flowmeter MultiVariable

Transmitter Quick Start Guide.

Rosemount 3051 Pressure Transmitter and Rosemount 3051CF Series Flowmeter Transmitter Quick

Start Guide.

Rosemount 2051 Pressure Transmitter and Rosemount 2051CF Series Flowmeter Transmitter Quick

Start Guide.

Process leaks may cause harm or result in death. To avoid process leaks, only use gaskets designed to seal with

the corresponding flange and o-rings to seal process connections. Flowing medium may cause the

Rosemount 585 Annubar Assembly to become hot and could result in burns.

If pipe/duct wall is less than 0.125-in. (3,2 mm) use extreme caution when installing sensor. Thin walls can

deform during welding, installation or from the weight of a cantilevered flowmeter. These installations may

require a fabricated outlet, saddle or external flowmeter support. Consult factory for assistance

Contents

Location and orientation . . . . . . . . . . . 4

Drill holes into pipe . . . . . . . . . . . . . . . . 7

Assemble and check fit-up . . . . . . . . . . 8

Weld mounting hardware . . . . . . . . . . 9

Insert the Rosemount Annubar Sensor . . . . . . . . . . 12

Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . 12

Product certifications . . . . . . . . . . . . . . . . . . . . . . . . . 18

4585_QIG_AB.fm Page 2 Monday, June 20, 2016 5:09 PM

Quick Start Guide

June 2016

Figure 1. Rosemount 585 Annubar Assembly Exploded View

Note

Use an appropriate pipe sealing compound rated for the service temperature on all

threaded connections.

A. Nuts

B. Remount mount instrument connection

C. Gasket

D. Studs

E. Opposite side support

F. Sensor flange

G. Rosemount 585 Annubar Sensor

H. Mounting flange assembly

4585_QIG_AB.fm Page 3 Monday, June 20, 2016 5:09 PM

June 2016

Quick Start Guide

1.0 Location and orientation

Correct orientation and straight run requirements must be met for accurate and

repeatable flow measurements. Refer to Table 1 for minimum pipe diameter

distances from upstream disturbances.

Table 1. Straight Run Requirements

In plane____________Out of plane Upstream pipe diameters

Downstream

pipe diameters

Without

straightening

vanes

With straightening

vanes

plane

Outof

plane

A’ CC’ B

N/A

4585_QIG_AB.fm Page 4 Monday, June 20, 2016 5:09 PM

Quick Start Guide

June 2016

Note

Consult the factory for instructions regarding use in square or rectangular

ducts.

“In plane A” means the sensor is in the same plane as the elbow. “Out of plane

A” means the bar is perpendicular to the plane of the elbow.

If proper lengths of straight run are not available, position the mounting such

that 80% of the run is upstream and 20% is downstream.

Use straightening vanes to reduce the required straight run length.

Row 6 in Table 1 applies to gate, globe, plug, and other throttling valves that

are partially opened, as well as control valves.

1.1 Misalignment

Rosemount 585 Annubar installation allows for a maximum misalignment of 3°.

Figure 2. Misalignment

N/A

±3°

±3°±3°

4585_QIG_AB.fm Page 5 Monday, June 20, 2016 5:09 PM

June 2016

Quick Start Guide

1.2 Horizontal Orientation

For proper venting and draining, the sensor should be located in the upper half of

the pipe for gas applications. For liquid and steam applications, the sensor should

be located in the bottom half of the pipe.

Figure 3. Horizontal Orientation

Gas Liquid and steam

Note

Top mounting for steam applications is an appropriate mounting option in many

cases. Consult Rosemount Customer Central for instructions regarding steam on top

mounting.

Steam on top

45°

Recommended

zone 90°

Recommended

zone 30°

45°45°

30° Recommended

zone 30°

45°

Recommended

zone 30°

30°

45°

Recommended

zone 30°

4585_QIG_AB.fm Page 6 Monday, June 20, 2016 5:09 PM

Quick Start Guide

June 2016

1.3 Vertical Orientation

The sensor can be installed in any position around the circumference of the pipe,

provided the vents are positioned properly for bleeding or venting. Optimal

results for liquid or steam are obtained when flow is up. For steam applications, a

90° spacer is included to provide water legs to ensure the transmitter stays within

temperature limits.

Figure 4. Liquid, Gas, or Steam

2.0 Drill holes into pipe

1. Determine the sensor size based on the probe width (see Table 2).

2. Depressurize and drain the pipe.

3. Select the location to drill the hole.

4. Determine the diameter of the hole to be drilled according to the

specifications in Table 2. Drill the mounting hole into the pipe with a hole saw

or drill. DO NOT TORCH CUT THE HOLE.

Note

Drill the hole 180° from the first hole for opposite- side support models.

Table 2. Sensor Size/Hole Diameter Chart

Sensor size Sensor width Hole diameter

11 0.80-in. (20,32 mm) 7/8-in. (19 mm) +1/32-in (0,8 mm) – 0.00

22 1.20-in. (30,48 mm) 15/16-in. (34 mm) +1/16-in. (1,6 mm) – 0.00

44 2.30-in. (58,42 mm) 21/2-in. (64 mm) +1/16-in. (1,6 mm) – 0.00

360°

Flow

4585_QIG_AB.fm Page 7 Monday, June 20, 2016 5:09 PM

June 2016

Quick Start Guide

5. A second identically sized hole must be drilled opposite the first hole so that

the sensor can pass completely through the pipe. To drill the second hole,

follow these steps:

a. Measure the pipe circumference with a pipe tape, soft wire, or string. (For

the most accurate measurement the pipe tape needs to be perpendicular to

the axis of flow.)

b. Divide the measured circumference by two to determine the location of the

second hole.

c. Re-wrap the pipe tape, soft wire, or string from the center of the first hole.

Then, using the number calculated in the preceding step, mark the center of

what will become the second hole.

d. Using the diameter determined in step 3, drill the hole into the pipe with a

hole saw or drill. DO NOT TORCH CUT THE HOLE.

6. Deburr the drilled holes on the inside of the pipe.

3.0 Assemble and check fit-up

For accurate measurement, use the following steps to ensure that Ports A and B

are equal distances from the inside walls of the pipe.

1. Assemble the Rosemount 585 to the mounting hardware with the gaskets and

bolts.

2. Hand tighten the bolts just enough to hold the position of the sensor centered

in the mounting hardware.

3. Check the fit of the assembly to the pipe by inserting a rule or stiff wire

through both mounting holes. Note the distance. All sensing holes must be

inside the pipe inner diameter. See Figure 5.

4. Add 1/16-in. (1,6 mm) to the measured distance for the weld gap and transfer

to the assembly starting at the high point of the butt weld branch connection.

5. Measure the distance from the high point of the butt weld branch connection

to the first sensing hole, port B, then subtract 1/16-in (1,6 mm).

6. Measure the distance from the end of the transferred length in step 4to the

last sensing hole, port A.

7. Compare the numbers obtained in steps 5and 6.

Small discrepancies can be compensated for with the fit-up of the mounting

hardware. Large discrepancies may cause installation problems or error.

Drill the appropriate diameter hole

through the pipe wall.

4585_QIG_AB.fm Page 8 Monday, June 20, 2016 5:09 PM

Quick Start Guide

June 2016

Figure 5. Fit-up Check for Rosemount 585 with Opposite-Side Support

4.0 Weld mounting hardware

1. Center the flanged assembly over the mounting hole, gap 1/16-in. (1,6 mm),

and measure the distance from the outer diameter of the pipe to the face of

the flange. Compare this to Table 3 and adjust the gap as necessary.

Table 3. Flange Sizes and ODF per Sensor Size

A. Outer Diameter to Flange (ODF)

B. Port A

C. Port B

D. The same within 1/8-in. (3 mm)

E. Pipe outside diameter

Sensor size Flange type Pressure class Flange size/rating/type ODF in. (mm)(1)

1 11/2-in. 150# RF 3.88 (99)

11 3 11/2-in. 300# RF 4.13 (105)

11 6 11/2-in. 600# RF 4.44 (113)

11 N 11/2-in. 900# RF 4.94 (125)

11 F 11/2-in. 1500# RF 4.94 (125)

11 T 11/2-in. 2500# RF 6.76 (172)

1 11/2-in. 150# RTJ 4.07 (103)

11 3 11/2-in. 300# RTJ 4.32 (110)

11 6 11/2-in. 600# RTJ 4.44 (113)

11 N 11/2-in. 900# RTJ 4.94 (125)

11 F 11/2-in. 1500# RTJ 4.94 (125)

11 T 11/2-in. 2500# RTJ 6.82 (173)

4585_QIG_AB.fm Page 9 Monday, June 20, 2016 5:09 PM

June 2016

Quick Start Guide

1DN40 PN16 RF 3.21 (81)

11 3DN40 PN40 RF 3.21 (81)

11 6DN40 PN100 RF 3.88 (99)

12.0-in. 150# RF 4.13 (105)

22 32.0-in. 300# RF 4.38 (111)

22 62.0-in. 600# RF 4.76 (121)

22 N2.0-in. 900# RF 5.88 (149)

22 F2.0-in. 1500# RF 5.88 (149)

22 T3.0-in. 2500# RF 9.87 (251)

12.0-in. 150# RTJ 4.32 (110)

22 32.0-in. 300# RTJ 4.63 (117)

22 62.0-in. 600# RTJ 4.82 (122)

22 N2.0-in. 900# RTJ 5.94 (151)

22 F2.0-in. 1500# RTJ 5.94 (151)

22 T3.0-in. 2500# RTJ 10.00 (254)

1DN50 PN16 RF 3.40 (86)

22 3DN50 PN40 RF 3.52 (89)

22 6DN50 PN100 RF 4.31 (109)

13.0-in. 150# RF 4.63 (117.5)

44 33.0-in. 300# RF 5.00 (126.9)

44 63.0-in. 600# RF 5.38 (136.6)

44 N4.0-in. 900# RF 8.19 (208.0)

44 F4.0-in. 1500# RF 8.56 (217.5)

44 T4.0-in. 2500# RF 11.19 (284.2)

13.0-in. 150# RTJ 4.82 (122)

44 33.0-in. 300# RTJ 5.25 (133)

44 63.0-in. 600# RTJ 5.44 (138)

44 N4.0-in. 900# RTJ 8.25 (209)

44 F4.0-in. 1500# RTJ 8.63 (219)

44 T4.0-in. 2500# RTJ 11.38 (289)

1DN80 PN16 RF 3.85 (98)

44 3DN80 PN40 RF 4.16 (106)

44 6DN80 PN100 RF 4.95 (126)

1. Tolerances for the ODF dimension above a 10-in. (254 mm) line size is ±0.060-in. (1,6 mm). Below

10-in. (254 mm) line size is ±0.030-in. (0,8 mm).

4585_QIG_AB.fm Page 10 Monday, June 20, 2016 5:09 PM

Otros manuales para Rosemount 585 Annubar

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Emerson

Emerson

Emerson Cybex SC KM 140 Manual de usuario

Emerson

Emerson Rosemount 2521 Series Manual de usuario

Emerson

Emerson AVOCENT Manual de usuario

Emerson

Emerson Rosemount 2140 Manual de usuario

Emerson

Emerson ASCO 7000 Series Manual de usuario

Emerson

Emerson ASCO 7000 Series Manual de usuario

Emerson

Emerson Alco Controls PS1 Series Manual de usuario

Emerson

Emerson Liebert NPS Manual de usuario

Emerson

Emerson PACSystems SLM080 Manual de usuario

Emerson

Emerson Rosemount 2110 Manual de usuario

Emerson

Emerson Rosemount 2130 Manual de usuario

Emerson

Emerson Alco Controls PS1 Series Manual de usuario

Emerson

Emerson VLS**435A Manual de usuario

Emerson

Emerson Rosemount 2160 Manual de usuario

Emerson

Emerson Rosemount 2460 Manual de usuario

Emerson

Emerson ASCO 185 Series Manual de usuario

Emerson

Emerson Avocent AutoView 2108 Instrucciones de instalación y mantenimiento

Emerson

Emerson SCKM120 Manual de usuario

Emerson

Emerson Rosemount 2120 Manual de usuario

Emerson

Emerson 2100 Manual de usuario

Emerson

Emerson LRA185KMM Manual de usuario

Emerson

Emerson Rosemount 2460 Manual de usuario

Emerson

Emerson AVENTICS PM1 Manual de usuario

Emerson

Emerson ASCO 300 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario