Ekwb EK-FB EVGA X58 LE Guía

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sample photo of EVGA X58 LE PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 6 screws on the back of

the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Northbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. One thermal pad (90x15x1 mm) and 2 (30x25x0,5) thermal

pads are enclosed with your water block. Please cut thermal pads as shown bellow.

(WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS

PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB EVGA X58 LE water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon7thofAugust,2009.

Southbridge

Northbridge

Mosfets

CPUsocket

18x4x0,5mm

75x7,5x1mm

25x25x0,5mm

18x4x1mm

12x4x0,5mm

12x4x1mm

Applythermalgreasehere.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric.

Thermal paste provides enough adhesive force for standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water block or

vice versa and attach it with enclosed screws as shown. Make sure that mounting

holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the Northbridge, and continue evenly outwards. Do not use too much pressure

screws (be very careful around Southbridge and use small amount of tightening force, since block has no standoffs. EKWB recommends

tightening screws around Southbridge in the end.), because motherboard might

bend and either cause bad contact with water block, or break

a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA X58 LE series are usually sold with

high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always

recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2,5x6 DIN7985

Please use the enclosed insulating

washers on all M2,5x6mm screws.

Fitting/barb

Spacer

Washer

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-AIO 120 D-RGB Manual de usuario

ekwb

ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario

ekwb

ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon... Manual de usuario

ekwb

ekwb EK-FC670 GTX Backplate Manual

ekwb

ekwb EK-Quantum RX 6800 Manual de usuario

ekwb

ekwb EK-FB GA 990FXA-UD7 Manual

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Manual de usuario

ekwb

ekwb EK-SBAY DDC Series Guía

ekwb

ekwb EK-FB KIT ASUS R5-E10 Guía

ekwb

ekwb EK-Quantum Magnitude Manual de usuario

ekwb

ekwb EK-FC Radeon Vega Strix Backplate Manual

ekwb

ekwb EK-Pro GPU WB RTX 8000 - Ni + Inox Manual de usuario

ekwb

ekwb EK-Classic Pump Reservoir 160 SPC PWM D-RGB Guía

ekwb

ekwb EK-FC480 GTX Manual

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manual de usuario

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manual de usuario

ekwb

ekwb EK-FCQ6000 Manual

ekwb

ekwb EK-FB EVGA CLASSIFIED 4-SLI Guía

ekwb

ekwb EK-FC R9-290X Manual

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock Manual de usuario

ekwb

ekwb Velocity - Intel Manual de usuario

ekwb

ekwb EK-FC 6970 V2 Manual

ekwb

ekwb EK-FC1080 GTX Backplate Guía

ekwb

ekwb EK-FC Titan X Guía

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB EVGA X58 LE Guía

Manuales populares de Hardware de computadora de otras marcas