Ekwb EK-FB EVGA CLASSIFIED 4-SLI Guía

Installation and mounting manuals for EK-FB EVGA CLASSIFIED 4-SLI water block:

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION. Sam

icture of EVGA CLASSIFIED 4-SLI motherboard.

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws or plugs. All heat sink

assembly screws should be removed. There are 16 screws on the back of the

motherboard.

2. CLEANING THE PCB. Carefully detach the original heat sink after removing all

fasteners securing it to the board and bracket. Wipe off the remains (by using non–

abrasive cloth or qtip, as shown on sample photo) of the original thermal compound

until the components and circuit board are completely clean. EKWB does not

recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Southbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

3.a. APPLYING THERMAL COMPOUND.

4. CUTTING THERMAL PADS. Your block comes with three prepared thermal

pads, which have to be placed on chips. (PLEASE REMOVE FOIL OF THERMAL

PADS PRIOR TO INSTALLATION.WARNING DIMENSIONS BELLOW ARE

SCALED!)

Thermal pad #1 (thickness 0,5mm).

Cut thermal pad #2 (thickness 1,5mm) in a way you can cover 2 areas shown

on right picture.

Cut thermal pad #3 (thickness 1mm) lengthwise in half so you get two sized

90x7,5 mm.

EKWB made sure you have more than enough thermal pads to cover all areas

needed to provide best cooling performance.

5. PLACING THERMAL PADS

Applythermal

compoundhere.

Thermalpads#2

Thermalpad#1 Thermalpads#3

     Releasedon11thofNovember,2009.

213

STEP 2: PREPARING YOUR WATER BLOCK

6. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric. Thermal

paste provides enough adhesive force for standoffs to stay in a place.

USE OF STANDOFFS IS OBLIGATORY. FURTHERMORE, PLEASE DO NOT USE TOO MUCH TIGHTENING FORCE ON THE 2 SCREWS AROUND SOUTHBRIDGE.

ONLY IN THIS WAY THE POTENTIAL DAMAGE TO YOUR MOTHERBOARD IS AVOIDED.

(This notice is written upon the letter from EVGA RMA department. They state they will deny all RMA's if they find improper mounting method was used.)

STEP 3: ATTACHING WATER BLOCK TO MOTHERBOARD AND CHECKING FOR CONTACTS

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a sprin

mountin

system; therefore when attachin

be very careful to ti

hten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the board.

Use the enclosed screws and washers as shown in diagram below

Temporarily r

emove the water blocks to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 4: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA CLASSIFIED 4-SLI series are usually sold with high flow

fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always recommended

for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

VERY IMPORTANT NOTICE

Once the installation is completed, it is always a good idea to test the circuit for leaks, prior to powering up the computer. We recommend a 24 hour leak test

prior to powering up the computer. Do not test the water block directly from city water pressure. This will bow the top of the housing and render the block

unusable (and will void your warranty).

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 14 screws M2,5x6 DIN7985

M2,5x6

     Releasedon11thofNovember,2009.

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manual de usuario

ekwb

ekwb EK-Dual DDC X-Top CSQ Manual

ekwb

ekwb Supremacy MX AMD Manual de usuario

ekwb

ekwb EK-FC780 Guía

ekwb

ekwb EK-FC460 GTX Manual

ekwb

ekwb EK-FC980 GTX Ti Strix Manual

ekwb

ekwb EK-Annihilator EX/EP Series Manual de usuario

ekwb

ekwb EK-FC970 GTX ACX Series Manual

ekwb

ekwb 115 Series Manual de usuario

ekwb

ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon... Manual de usuario

ekwb

ekwb EK-FB KIT GA X58 (UD7) Manual

ekwb

ekwb EK-FC R9-290X Manual

ekwb

ekwb EK-XLC PREDATOR 240 Manual de usuario

ekwb

ekwb EK-XRES 100 Revo D5 Series Manual

ekwb

ekwb EK-FCQK5000 Manual

ekwb

ekwb Vector 2 FTW3 RTX 3080/90 ABP Manual de usuario

ekwb

ekwb EK-FC780 GTX Ti Series Manual de usuario

ekwb

ekwb EK-FC980 GTX TF5 Guía

ekwb

ekwb EK-FC590 GTX Manual

ekwb

ekwb EK-FC7970 Lightning Manual

ekwb

ekwb EK-Supremacy Classic RGB Manual de usuario

ekwb

ekwb EK-FC7970 DCII Guía

ekwb

ekwb EK-FC R9-390X TF5 Series Manual

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-FB EVGA CLASSIFIED 4-SLI Guía

Manuales populares de Hardware de computadora de otras marcas