Ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector FE RTX 3070

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process, to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 9

INSTALLING THE WATER BLOCK 9

PLACING THE BLOCK ON THE GRAPHICS CARD 9

ATTACHING THE BLOCK TO THE GRAPHICS CARD 10

CHECKING FOR CONTACT 10

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 11

INSTALLATION OF FITTINGS AND TUBING 11

CONNECTING THE D-RGB LED STRIP 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

BOX CONTENTS

4 mm

6 mm

8 mm

M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)

M2.5 Nut (2 pcs)

M2.5x6 AX1 Screw (13 pcs)

Allen Key 2.5 mm (1 pc)

Thermal Pad F 1.0 mm (4 pcs)

Thermal Grease (1 pc)

M2.5x8 AX1 Screw (2 pcs)

M2.5x4 AX1 Screw (16 pcs)

EK-Quantum Vector FE RTX 3070 PVC Washer M2.5 (16 pcs)

120 mm

16 mm

EK-Plug G1/4 (2 pcs)

Universal Mounting Mechanism – You may not need every

screw from this package.

- 5 -

WATER BLOCK DIMENSIONS

204.90 mm

193.40 mm

179.90 mm

97.90 mm

36.40 mm

65.40 mm

20.65 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

Technical Speciﬁcation:

Dimensions (LxHxW): 205 x 98 x 20.5 mm

D-RGB (Addressable RGB) Cable - Length: 500 mm

D-RGB LED Count: Plexi - 5

D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)

M4 x 10 DIN7984 SCREW

TOP PLATE

(PLEXI,ACETAL)

COLDPLATE

PLEXI INSERT

JE T PL AT E

TERMINAL O-RING

15 x 1 mm

M4 x 10 DIN7991 SCREW

M3.5 x 2.5 STANDOFF

EK BADGE

D-RGB LED STRIP

(PLEXI VERSION ONLY)

MAIN O-RING 116 x 2 mm

TERMINAL

(PLEXI,A CETAL)

M4 X 27

DIN7984

SCREW

STANDOUT

(NICKEL,BLACK ELOX)

M3.5 x 12.60

STANDOFF

M4 x 2.5

STANDOFF

- 7 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

Place your graphics card on the ﬂat surface and carefully remove the

stock cooler. Do not forget to unplug all the LED and fan connectors.

Pay attention to the following steps in order to install the EK-Quantum

Vector FE RTX 3070 water block onto the graphics card.

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers.

STEP 2

- 8 -

STEP 1

Your GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Replacement thermal pads:

4x Thermal Pad F 1.0mm – (120X16mm) EAN: 3830046996732

STEP 1

Thermal Pad F – 1.0 mm (120 x 16 mm)

CUTTING AND PLACING THERMAL PADS

120 mm

16 mm

1 mm

STEP 2

Once cut to size, thermal pads should be placed on the PCB,

as illustrated. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

Thermal Pad F 1.0mm

- 9 -

Thermal Grease

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the CPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 1

APPLYING THERMAL COMPOUND

For this Step, you will need:

INSTALLING THE WATER BLOCK

STEP 1

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks.

Carefully position the water block with preinstalled standoffs on

the graphics card. During this process, make sure you have aligned

mounting holes of the PCB with holes of the water block (same

applies to other tops).

Pay attention not to use too much force when pressing the

block down to the PCB since chip dies are prone to cracking.

STEP 1

- 10 -

For this Step, you will need:

M 2.5 PVC Washer

(9 pcs)

M2.5 x 4 AX1

(11 pcs)

Phillips Head

Screwdriver

4 mm

STEP 2

M2.5 x 4 AX1 SCREW

M2.5 PVC WASHER

WITHOUT

PVC WASHER

WITHOUT

PVC WASHER

STEP 2

ATTACHING THE BLOCK TO THE GRAPHICS CARD

Use eleven (11) M2.5 X 4 AX1 screws and nine (9) M2.5 PVC

washers. Tighten the screws evenly using the Phillips head

screwdriver. EK recommends you start tightening the screws

around the GPU core first, and then continuing outward to prevent

the damage to the GPU.

CHECKING FOR CONTACT

If necessary, temporarily remove the water block to check for uniform

surface contact between the block and components. Pay special

attention to the VRM section of the graphics card. Check whether

the water block makes contact with the intended integrated circuit.

Then repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check

again or contact our support service at

https://www.ekwb.com/customer-support/.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de ekwb

ekwb

ekwb EK-FC R9 290X DCII Guía

ekwb

ekwb EK-FB KIT ASUS R5-E10 Guía

ekwb

ekwb EK-FC780 GTX Ti Series Manual de usuario

ekwb

ekwb EK-Loop Fan FPT 120 FAN Manual de usuario

ekwb

ekwb GTX 1080 Ti Aorus Backplate Guía

ekwb

ekwb EK-FC7870 GTX Manual

ekwb

ekwb EK-Velocity sTR4 Manual de usuario

ekwb

ekwb EK-FC1080 GTX Ti Aorus RGB Manual de usuario

ekwb

ekwb EK-Loop PCI Bracket Pass-Through Manual de usuario

ekwb

ekwb 3831109816202 Guía

ekwb

ekwb EK-FC7850 Guía

ekwb

ekwb EK-FC R9 Fury X Guía

ekwb

ekwb EK-Quantum Velocity 2 Manual de usuario

ekwb

ekwb EK-FB GA X299 GAMING Monoblock Manual de usuario

ekwb

ekwb EK-FC690 GTX Backplate Manual

ekwb

ekwb EK-Quantum Magnitude Manual de usuario

ekwb

ekwb EK-FC R9-295X2 Manual

ekwb

ekwb EK-FC Titan XXL Manual

ekwb

ekwb EK-FC460 GTX Manual

ekwb

ekwb EK-Quantum Kinetic TBE DDC PWM Series Manual de usuario

ekwb

ekwb EK-Classic 115x/20xx D-RGB Manual de usuario

ekwb

ekwb EK-FB ASUS Max4 Extreme Guía

ekwb

ekwb EK-FB ASUS Strix X299-E RGB Monoblock Manual de usuario

ekwb

ekwb EK-FC780 GTX Jetstream Manual

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

ekwb EK-Quantum Vector FE RTX 3070 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas