DFI G7B630-N Manual de usuario

G7B630-N

G7B630-B

System Board

User’s Manual

935-G7B631-000G

A93900646

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Special Features of the System Board..................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers, Utilities and Software Applications......................................................

Installation Notes.......................................................................................................................

Appendix A - Enabling Hyper-Threading Technology......................

Appendix B - System Error Messages...............................................

Appendix C - Troubleshooting..........................................................

Appendix D - Watchdog Sample Code..............................................

100

102

117

118

121

123

127

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery manufactur-

er’s

instructions.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;A user’s manual

;One IDE cable

;One FDD cable

;Two Serial ATA data cables

;Two Serial ATA power cables

;One bracket mounted with a serial port

;One bracket mounted with a 1394 port (G7B630-N only)

;Two USB port cables

;One “Main Board Utility” CD

;One I/O shield

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

• LGA 775 socket for:

- Intel®CoreTM2 Duo (Conroe family)

- Intel®Pentium®D

- Intel®Pentium®4 or Intel®Celeron

- Intel®Celeron D

• Supports Intel Enhanced Memory 64 Technology (EMT64T)

• Supports Enhanced Intel SpeedStep Technology (EIST)

• Supports Intel Hyper-Threading Technology

• Supports 1066/800/533MHz FSB

• Intel®chipset

- Northbridge: Intel®Q965 Express chipset

- Southbridge: Intel®ICH8

• Four 240-pin DDR2 DIMM sockets

• Supports DDR2 533, DDR2 667 and DDR2 800 DIMMs

• Supports dual channel (128-bit wide) memory interface

• Supports up to 8GB system memory

• Supports non-ECC unbuffered DIMMs

• Award BIOS

• 8Mbit SPI flash memory (G7B630-N)

4Mbit SPI flash memory (G7B630-B)

• Supports ACPI specification and OS Directed Power Manage-

ment

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-LAN

- Wake-On-Ring

- RTC timer to power-on the system

• System power management supported

• CPU stopped clock control

• Microsoft®/Intel®APM 1.2 compliant

• Soft Power supported - ACPI v2.0 specification

• AC power failure recovery

• Monitors CPU/system temperature and overheat alarm

• Monitors Vcore/VCC3/VBAT/3VSB/12V/1.25V/1.8V/5V voltages

and failure alarm

• Monitors CPU/2nd/system fan speed

• Read back capability that displays temperature, voltage and fan

speed

• Watchdog Timer function

Processor

Chipset

System Memory

BIOS

Energy Efficient

Design

Damage Free

Intelligence

Chapter 1 - Introduction

Specifications

Introduction

Graphics

Audio

LAN

Storage

IEEE 1394

(G7B630-N only)

Rear I/O

I/O Connectors

Expansion Slot

• Built-in Intel Graphics Media Accelerator 3000

• Realtek ALC262 High Definition audio CODEC

• 2-channel audio output

• 1 stereo DAC supports 16/20/24-bit PCM format with 44.1/48/

96/192KHz sample rate

• 2 stereo ADCs support 16/20-bit PCM format with 44.1/48/96/

192KHz sample rate

• S/PDIF-in/out interface

• G7B630-N: Intel 82566DM and Marvell 88E8053 PCI Express

Gigabit Ethernet controllers

G7B630-B: Marvell 88E8053 PCI Express Gigabit Ethernet controller

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Intel ICH8 supports:

- 3 Serial ATA ports

- SATA speed up to 3Gb/s

• Silicon Image Sil3811 SATA to PATA bridge supports:

- One UltraDMA 133/100/66/33 IDE that supports one parallel

ATA device (Master mode only)

• VIA VT6307

• Supports two 100/200/400 Mb/sec ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 1 DB-9 serial port

• 1 DB-15 VGA port

• 2 RJ45 LAN ports (G7B630-N only)

1 RJ45 LAN port (G7B630-B only)

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line-out jacks

• 3 connectors for 6 additional external USB 2.0/1.1 ports

• 2 connectors for external IEEE 1394 ports (G7B630-N only)

• 1 connector for an external COM 2 port

• 1 Digital I/O connector

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF-in/out connector

• 1 connector for IrDA interface

• 3 Serial ATA connectors

• 1 40-pin IDE connector

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 4-pin 12V power connector

• 1 chassis open connector

• 1 front panel connector

• 3 4-wire fan connectors

• 1 PCI Express x16 slot

• 2 PCI Express x1 slots

• 4 PCI slots

Introduction

Temperature

Humidity

PCB

• Operating: 0oC to 60oC

• Non-operating: -40oC to 85oC

• Operating: 10% to 90%

• 4 layers, ATX form factor

• 30.5cm (12") x 24.4cm (9.6")

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

DFI

DFI DL631-C226 Manual de usuario

DFI

DFI Lanparty JR P45-T2RS Manual de usuario

DFI

DFI Blood-Iron G41-T33 Manual de usuario

DFI

DFI SB100-NRM Manual de usuario

DFI

DFI CL630-CRM Manual de usuario

DFI

DFI LanParty UT NF4 SLI EXPERT Venus Manual de usuario

DFI

DFI LanParty PRO875B Manual de usuario

DFI

DFI G586OPC/E Manual de usuario

DFI

DFI CMS101 Manual de usuario

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Manual de usuario

DFI

DFI CMS630-W480E Manual de usuario

DFI

DFI CS330 Manual de usuario

DFI

DFI FS053 Manual de usuario

DFI

DFI CA100-D Manual de usuario

DFI

DFI CB50-V3 Manual de usuario

DFI

DFI CA64-TC Manual de usuario

DFI

DFI PW65-L Manual de usuario

DFI

DFI AM75-EC Manual de usuario

DFI

DFI CA63-SC Manual de usuario

DFI

DFI CL60-LX Manual de usuario

DFI

DFI SD101 Manual de usuario

DFI

DFI 915P-TAL Manual de usuario

DFI

DFI P2XBL/E Manual de usuario

DFI

DFI BL600-DR Manual de usuario

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario