DFI LanParty PRO875B Manual de usuario

Rev. B+

System Board

User’s Manual

74820402

This publication contains information that is protected by copy-

right. No part of it may be reproduced in any form or by any

means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with re-

spect to the contents or use of this manual and specifically dis-

claims any express or implied warranties of merchantability or

fitness for any particular purpose. The user will assume the entire

risk of the use or the results of the use of this document. Further,

the manufacturer reserves the right to revise this publication and

make changes to its contents at any time, without obligation to

notify any person or entity of such revisions or changes.

Trademarks

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. Intel®and Pentium®4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award Soft-

ware, Inc. Other trademarks and registered trademarks of prod-

ucts appearing in this manual are the properties of their respec-

tive holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servic-

ing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

by the manufacturer.

• Dispose of used batteries according to the battery manufac-

turer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more

than 10A current at 5V DC. There is a risk of fire for devices

that exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's author-

ity to operate the equipment.

2. Shielded interface cables must be used in order to comply

with the emission limits.

Important Configuration and Driver Installation

Rules

HighPoint RAID IDE Controller

By default, the HighPoint RAID IDE controller is enabled. If you

are not using this function, make sure to set the “RAID Device

Control” field in the Genie BIOS Setting submenu of the Award

BIOS to Disabled.

Make sure to follow the rule mentioned above. Doing it other-

wise will slow down the boot up time and affect the perform-

ance of the system.

Driver Installation Rules

Please follow the installation sequence below.

1. Install the “Audio Drivers”.

2. Install the “Intel Chipset Software Installation Utility”.

3. Install the other drivers and utilities.

Make sure to follow this sequence. Doing it otherwise will slow

down the boot up time and affect the performance of the sys-

tem.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..............................................................................

1.2 Hyper-Threading Technology Functionality Requirements.

1.3 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .........................................................................................

2.2 System Memory..........................................................................................................

2.3 CPU...........................................................................................................................................

2.4 Jumper Settings............................................................................................................

2.5 Rear Panel I/O Ports.............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility..................................................................................

3.2 Intel LAN BIOS Setting Utility.....................................................................

3.3 Intel ICH5R BIOS Setting Utility................................................................

3.4 HighPoint BIOS Configuration Utility...................................................

3.5 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.............................................................

4.2 Drivers, Utilities and Software Applications.................................

4.3 3D Audio Configuration.................................................................................

4.4 Installation Notes..................................................................................................

104

105

106

108

111

128

131

Introduction

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...................................

Appendix B - CPU Fan Protection

B.1 CPU Fan Protection..............................................................................................

Appendix C - System Error Messages

C.1 POST Beep......................................................................................................................

C.2 Error Messages............................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist..............................................................................

132

135

136

138

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®875P chipset

- Intel®82875P Memory Controller Hub (MCH)

- Intel®82801ER I/O Controller Hub (ICH5R)

Processor

The system board is equipped with Socket 478 for installing one

of the following supported processors.

• Intel®Pentium®4 (Prescott and Northwood) processor up to

3.2GHz+

- Intel Hyper-ThreadingTechnology

- FSB: 533MHz and 800MHz

• Intel®Celeron®processor

- 400MHz system data bus

Note:

Refer to section 1.2 and appendix A for more information on

the Hyper-ThreadingTechnology.

System Memory

• Supports dual channel (128-bit wide) memory interface

- Each channel supports 2 DIMM sockets

• Supports up to 4GB system memory

• Supports Dynamic mode to optimize system performance

• Synchronous operation with processor system bus

- PC2100/PC2700/PC3200 (DDR266/DDR333/DDR400)

with 800MHz FSB CPU (supports PAT mode). DDR333

will run at 320MHz memory frequency when used with

800MHz FSB CPU.

Chapter1 - Introduction

Introduction

Performance Acceleration Technology (PAT)

PAT mode is supported only when the system uses DDR400

with 800MHz FSB CPU. PAT performs data transactions directly

from the CPU to the system memory, bypassing the normal path

of operation. This reduces the MCH timing therefore providing

improved system performance.

CMOS Reloaded

CMOS Reloaded is a technology that allows storing multiple

user-defined configurations by using the BIOS utility to save, load

and name the configurations. This is especially useful to

overclockers who require saving a variety of overclocked con-

figurations and being able to conveniently switch between these

configurations simultaneously.

Expansion Slots

The system board is equipped with 1 AGP slot and 5 PCI slots.

AGP (Accelerated Graphics Port)

• Supports AGP 3.0 (AGP 4x and 8x) and AGP 2.0 (AGP 1x and

4x) spec.

• Supports 1.5V AGP 8x (2.13GB/sec.) and AGP 4x (1066MB/

sec.) add-in cards.

AGP is an interface designed to support high performance 3D

graphics cards for 3D graphics applications. It handles large

amounts of graphics data with the following features:

Density Width

Single/Double

184-pin DDR

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/NA

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/NA

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/NA

- Use PC2100/PC2700 (DDR266/DDR333) with 533MHz

FSB CPU

- Use PC2100 (DDR266) with 400MHz FSB CPU

• Supports ECC/non-ECC DIMMs

• Supports unbuffered DIMMs

Introduction

• Pipelined memory read and write operations that hide

memory access latency.

• Demultiplexing of address and data on the bus for nearly

100 percent efficiency.

Note:

AGP 2x and 3.3V AGP cards are not supported.

Onboard Audio Features

• 20-bit stereo full-duplex codec with independent variable sam-

pling rate

• High quality differential CD input

• True stereo line level outputs

• S/PDIF-in/out interface

• 6-channel audio output

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio

The center/bass and rear out jacks which supports four audio

output signals: center channel, subwoofer, rear right channel and

rear left channel; together with the line-out (2-channel) jack sup-

port 6-channel audio output.

Onboard LAN Features

• Uses 82547EI Gigabit LAN CSA (Communication Streaming

Architecture) interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Introduction

Compatibility

• PCI 2.2 and AC ’97 compliant

• Intel AGP version 3.0

ICH5R SATA IDE/RAID Interface

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Two SATA (Serial ATA) interfaces which are compliant with

SATA 1.0 specification (1.5Gbps interface)

• Supports RAID 0 and 1

ATA RAID - Redundant Array of Independent Disk

• Uses HighPoint 372N RAID controller

• RAID 0, 1, 0+1 and 1.5

- RAID 1.5 performs data stripping and mirroring simultane-

ously using two drives only

• Two independent IDE channels support up to 4 drives (ATA/

33, ATA/66, ATA/100, ATA/133 or EIDE)

• Supports PIO modes 0/1/2/3/4, DMA modes 0/1/2 and

UDMA modes 0/1/2/3/4/5/6

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/

sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wire-

less connectivity between your computer and peripheral devices.

The IRDA (Infrared Data Association) specification supports data

transfers of 115K baud at a distance of 1 meter.

Otros manuales para LanParty PRO875B

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario