DFI 915P-TAL Manual de usuario

85200507

915P-TAL

915PL-TAL

System Board

User’s Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for

identification purpose only and are the properties of the respective

owners.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

About this Manual

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should al-

ways be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.The

autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

About the Package

The system board and accessories in the package may not come

similar to the information stated in this manual. This may differ in

accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please

contact your dealer or sales representative.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product

specifications.

2. The warranty is void if the product has been subjected to

physical abuse, improper installation, modification, accidents or

unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service,

adjustments or repairs on the product, whether in or out of

warranty. It must be returned to the purchase point, factory or

authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Table of Contents

Chapter 1 - Introduction

1.1 Specifications......................................................................................................................

1.2 Special Features of the System Board.....................................................

1.3 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...........................................................................................

2.2 System Memory...........................................................................................................

2.3 CPU........................................................................................................................................

2.4 Jumper Settings.............................................................................................................

2.5 Rear Panel I/O Ports..............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility....................................................................................

3.2 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Drivers, Utilities and Software Applications.....................................

4.2 Installation Notes......................................................................................................

103

Introduction

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...........................................

Appendix B - System Error Messages

B.1 POST Beep....................................................................................................................

B.2 Error Messages...........................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist.................................................................................

104

107

109

Introduction

Chapter 1 - Introduction

Specifications

Processor

• Intel®Pentium®4 Prescott processor

- Hyper-Threading Technology

- 533MT/s and 800MT/s (200MHz) system bus interface

• Socket LGA 775 (LAN Grid Array)

Chipset

• North bridge:

- Intel®915P Express chipset (915P-TAL)

- Intel®915PL Express chipset (915PL-TAL)

South bridge:

- Intel®82801FB I/O Controller Hub (ICH6)

System Memory

• DIMM sockets

- Four 184-pin DDR DIMM sockets (915P-TAL)

- Two 184-pin DDR DIMM sockets (915PL-TAL)

• Maximum memory

- Up to 4GB system memory (915P-TAL)

- Up to 2GB system memory (915PL-TAL)

• Supports PC2700 (DDR333) and PC3200 (DDR400) DIMMs

• Supports dual channel (128-bit wide) memory interface

• Supports non-ECC x8 and x16 DIMMs

• Supports up to 512Mb DRAM densities

• Supports unbuffered DIMMs

Note:

The system board does not support 16Mx8 DRAM.

BIOS

• Award BIOS

• 4Mbit flash memory

Introduction

Energy Efficient Design

• Supports ACPI specification and OS Directed Power

Management

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-Ring (external modem)

- Wake-On-LAN

- RTC timer to power-on the system

• AC power failure recovery

Hardware Monitor

• Monitors CPU/system temperature and overheat alarm

• Monitors Vcore/V3SB/Vcc3/Vcc5/12V/V5SB/VBAT voltages

• Monitors the speed of the CPU/system fan

• CPU Overheat Protection function monitors CPU temperature

and fan during system boot-up - automatic shutdown upon

system overheat

Onboard Audio Features

• 6-channel audio CODEC

• Full-duplex codec with independent variable sampling rate

• True stereo line level outputs

• S/PDIF-in/out interface

Onboard LAN Features

• Realtek RTL8100C PCI LAN controller

• Fully compliant to IEEE 802.3 (10BASE-T) and 802.3u

(100BASE-TX) standards

• Integrated power management functions

• Supports wire for management

Serial ATA Interface

• Supports four SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification (1.5Gbps interface)

IEEE 1394 Interface

• Supports two 100/200/400 Mb/sec ports

IDE Interface

• One IDE connector supports up to two UltraDMA100Mbps

hard drives

Introduction

Rear Panel I/O Ports

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-25 parallel port

• 2 DB-9 serial ports

• 1 IEEE 1394 port

• 1 RJ45 LAN port

• 4 USB 2.0/1.1 ports

• Line-in, line-out and mic-in jacks

I/O Connectors

• 2 connectors for 4 additional external USB 2.0/1.1 ports

• 1 connector for 1 external IEEE 1394 port

• 1 front audio connector for external line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF connector

• 1 IrDA connector

• 4 Serial ATA connectors

• 1 IDE connector

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 4-pin ATX 12V power connector

• 1 front panel connector

• 2 fan connectors

Expansion Slots

• 1 PCI Express x16 slot

• 2 PCI Express x1 slots

• 3 PCI slots

PCB

• microATX form factor

• 24.4cm (9.6") x 24.4cm (9.6")

Introduction

Special Features of the System Board

PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses

the ability to scale speeds by forming multiple lanes. The system

board currently supports the physical layer of x1 and x16 lane

widths.

The x1 PCI Express lane supports transfer rate of 2.5 Gigabytes

(250MBbps) per second. The PCI Express architecture also provides

a high performance graphics infrastructure by doubling the capability

of the existing AGP 8x designs over a x16 PCI Express lane that

provides 4 Gigabytes per second transfer rate.

Hyper-Threading Technology Functionality Requirements

The system board supports Intel processors with Hyper-Threading

Technology. Enabling the functionality of Hyper-Threading Technology

for your computer system requires ALL of the following platforms.

Components:

• CPU - an Intel®Pentium®4 Processor with HT Technology

• Chipset - an Intel®chipset that supports HT Technology

• BIOS - a BIOS that supports HT Technology and has it enabled

• OS - an operating system that includes optimizations for HT

Technology

Please refer to Appendix A for information a bout enabling the

functionality of the Hyper-Threading Technology. For more information

on Hyper-Threading Technology, go to: www.intel.com/info/

hyperthreading.

Otros manuales para 915P-TAL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

DFI

DFI KD600-H110/Q170 Manual de usuario

DFI

DFI PB50-ZX Manual de usuario

DFI

DFI LR100-N16 Series Manual de usuario

DFI

DFI SR100-N Manual de usuario

DFI

DFI MB331-CRM Manual de usuario

DFI

DFI G5C100-B Manual de usuario

DFI

DFI P5BVP Manual de usuario

DFI

DFI G7V600-B Manual de usuario

DFI

DFI PB50-V3 Manual de usuario

DFI

DFI CMS632-W480E Manual de usuario

DFI

DFI C586HX Manual de usuario

DFI

DFI SD330-Q170 Manual de usuario

DFI

DFI LanParty 925X-T2 Manual de usuario

DFI

DFI TGU171 Manual de usuario

DFI

DFI CM64-AL Manual de usuario

DFI

DFI ADS310-R680E Series Manual de usuario

DFI

DFI CS620-H310 Manual de usuario

DFI

DFI CMS171 Manual de usuario

DFI

DFI G5M300-P Manual de usuario

DFI

DFI LanParty 865PE Manual de usuario

DFI

DFI CMS630-W480E Manual de usuario

DFI

DFI SB331-IPM Manual de usuario

DFI

DFI LanParty DK P35 series Manual de usuario

DFI

DFI 586IHX Manual de usuario

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario