DFI SB100-NRM Manual de usuario

SB100-NRM

System Board

User’s Manual

A16960450

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Changes after the publication’s first release will be based on the product’s revi-

sion. The website will always provide the most updated information.

Trademarks

All trademarks and registered trademarks of products appearing in this manual

are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

Introduction

Table of Contents

Trademarks........................................................................................ 2

FCC and DOC Statement on Class B.............................................. 3

About this Manual ............................................................................. 6

Warranty .......................................................................................... 6

Static Electricity Precautions............................................................. 7

Safety Measures................................................................................. 7

About the Package ............................................................................ 8

Before Using the System Board........................................................ 8

Chapter 1 - Introduction .................................................................. 9

Specifications.................................................................................. 9

Features ...................................................................................... 12

Chapter 2 - Hardware Installation.................................................. 15

System Board Layout .................................................................... 15

System Memory ........................................................................... 16

Installing the DIM Module ......................................................... 18

CPU ............................................................................................ 20

Installing the CPU .................................................................... 21

Installing the Fan and Heat Sink ................................................ 25

Jumper Settings............................................................................. 27

Clear CMOS Data ..................................................................... 27

PS/2 Power Select.................................................................... 28

USB Power Select..................................................................... 29

Power-on Select ....................................................................... 30

COM1/COM2 RS232/RS422/RS485 Select.................................... 31

COM1/COM2 RS232/Power Select............................................... 32

Rear Panel I/O Ports..................................................................... 33

PS/2 Mouse and PS/2 Keyboard Ports......................................... 34

COM (Serial) Ports ................................................................... 35

VGA Port................................................................................. 36

DVI-I Port ............................................................................... 37

RJ45 LAN Ports ........................................................................ 38

USB Ports................................................................................ 39

Audio...................................................................................... 41

Introduction

I/O Connectors............................................................................ 42

S/PDIF Connector..................................................................... 42

Digital I/O Connectors .............................................................. 43

SATA (Serial ATA) Connectors .................................................... 44

Cooling Fan Connectors............................................................. 45

Chassis Instrusion Connector .................................................... 46

Power Connectors .................................................................... 47

Standby Power LED .................................................................. 48

Front Panel Connectors ............................................................. 49

Expansion Slots ....................................................................... 50

Battery ................................................................................... 51

Chapter 3 - BIOS Setup.................................................................. 52

Overview ..............................................................................................................52

AMI BIOS Setup Utility ................................................................. 54

Main ....................................................................................... 54

Advanced ................................................................................ 55

Chipset ................................................................................... 70

Boot ....................................................................................... 76

Security .................................................................................. 78

Save & Exit ............................................................................. 80

Updating the BIOS........................................................................ 81

Notice: BIOS SPI ROM.................................................................. 82

Chapter 4 - Supported Software ................................................... 83

Chapter 5 - RAID ........................................................................ 107

RAID Levels .......................................................................................................107

Settings................................................................................................................108

Chapter 6 - Intel AMT Settings ................................................... 113

Overview ............................................................................................................113

Enable Intel®AMT in the AMI BIOS ............................................................114

Enable Intel®AMT in the Intel®Management Engine BIOS

Extension (MEBX) Screen ..............................................................................116

Appendix A - NLITE and AHCI Installation Guide ....................... 141

Appendix B - Watchdog Sample Code ......................................... 153

Appendix C - System Error Message............................................ 154

Appendix D - Troubleshooting...................................................... 156

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

One SB100-NRM motherboard

Two Serial ATA data cables

One Serial ATA power cable

One USB port cable

One COM port cable (with bracket)

One I/O shield

One DVD

One QR (Quick Reference)

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Optional Items

USB port cable

COM port cable

Serial ATA data cable

Serial ATA power cable

PS/2 Keyboard/Mouse cable

IDE cable

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Audio

LAN

Chapter 1 - Introduction

• LGA 1155 socket for:

- 3rd generation Intel®CoreTM processors

(22nm process technology) (Rev. AD0 or later)

: Intel®CoreTM i7-3770 (8M Cache, up to 3.9GHz); 77W

: Intel®CoreTM i5-3550S (6M Cache, up to 3.7GHz); 65W

: Intel®CoreTM i3-3220 (3M Cache, 3.3GHz); 55W

: Intel®Pentium®G2120 (3M Cache, 3.1 GHz); 65W

- 2nd generation Intel®CoreTM processors

(32nm process technology)

: Intel®CoreTM i7-2600 (8M Cache, up to 3.8 GHz); 95W

: Intel®CoreTM i5-2400 (6M Cache, up to 3.4 GHz); 95W

: Intel®CoreTM i3-2120 (3M Cache, 3.3 GHz); 65W

: Intel®Pentium®G850 (3M Cache, 2.9 GHz); 65W

• Intel®Advanced Vector Extensions (Intel®AVX) Instructions

• Intel®Turbo Boost Technology

• Intel®Q67 PCH (Platform Controller Hub)

• Two 240-pin DDR3 DIMM sockets

• Supports DDR3 1333/1600MHz (3rd generation processors)

Supports DDR3 1066/1333MHz (2nd generation processors)

• Supports up to 16GB system memory

• Supports dual channel memory interface

• DRAM device technologies: 1Gb, 2GB and 4Gb DDR3 DRAM

technologies are supported for x8 and x16 devices, unbuf-

fered, non-ECC

• 1 PCIe x16 slot

- Supports Gen 3.0 (3rd generation processors)

- Supports Gen 2.0 (2nd generation processors)

• Intel®HD Graphics

• Display ports: DVI-I (DVI-D signal) and VGA

• DVI-I supports up to 1920x1200 @ 60Hz resolution

• VGA supports up to 2048x1536 @ 75Hz resolution

• Supports 6 Graphics Execution Units (EUs)

• Intel®Clear Video Technology

• DirectX Video Acceleration (DXVA) support for accelerating

video processing

• Realtek ALC262 2-channel High Definition Audio

• High performance DACs with 100dB SNR

• ADCs with 90dB SNR

• Two stereo DACs support 24-bit PCM format for stereo au-

dio playback

• Three stereo ADCs support 20-bit PCM format for multiple

input streaming

• S/PDIF audio interface

• Intel 82579LM with iAMT8.0 Gigabit Ethernet Phy

• Intel 82574L PCI Express Gigabit Ethernet controller

• Integrated 10/100/1000 transceiver

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Specifications

Introduction

Serial ATA

Intel Active

Management

Technology

(AMT)

TPM (optional)

Rear Panel I/O

Ports

I/O Connectors

BIOS

Energy Efficient

Design

• 4 Serial ATA ports

- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s

- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s

• Integrated Advanced Host Controller Interface (AHCI) con-

troller

• Supports RAID 0/1/5/10

• Supports iAMT8.0

• Out-of-band system access

• Remote troubleshooting and recovery

• Hardware-based agent presence checking

• Proactive alerting

• Remote hardware and software asset tracking

• TPM - Trusted Platform Module

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement and pass-

word protection

• 1 mini-DIN-6 PS/2 mouse port and PS/2 keyboard port

• 1 mini-DIN-6 PS/2 keyboard port

• 2 DB-9 serial ports

- Supports RS232/422/485 (RS232 and/or Power)

• 1 DB-15 VGA port

• 1 DVI-I port (DVI-D signal)

• 2 RJ45 LAN ports

• 4 USB 2.0/1.1 ports

• Mic-in, Line-in and Line-out jacks

• 2 connectors for 4 external USB 2.0/1.1 ports

• 2 connectors for 2 external RS232 serial ports

• 1 8-bit Digital I/O connector

• 1 Digital I/O power connector

• 1 front audio connector for line-out and mic-in jacks

• 1 S/PDIF connector

• 4 Serial ATA ports

• 1 24-pin ATX power connector

• 1 4-pin 12V power connector

• 1 chassis intrusion connector

• 1 front panel connector

• 2 fan connectors

• AMI BIOS

- 64Mbit SPI BIOS

• Supports ErP Lot6 power saving (optional)

• Supports ACPI

• System Power Management

• Wake-On-Events include:

- Wake-On-PS/2 KB/Mouse

- Wake-On-USB KB/Mouse

- Wake-On-LAN

- RTC timer to power-on the system

• CPU stopped clock control

• AC power failure recovery

Tabla de contenidos

Otros manuales de Placa madre de DFI

DFI

DFI KU173 Manual de usuario

DFI

DFI G7G330-B Manual de usuario

DFI

DFI G5C900-B Manual de usuario

DFI

DFI AL102 Manual de usuario

DFI

DFI Blood-Iron G41-T33 Manual de usuario

DFI

DFI LanParty DK P35 series Manual de usuario

DFI

DFI CB64-BX Manual de usuario

DFI

DFI Blood-iron P45 Series Manual de usuario

DFI

DFI nF4 Ultra-DAGF Manual de usuario

DFI

DFI SD170 Manual de usuario

DFI

DFI MB630-CRM Manual de usuario

DFI

DFI SD630-H110-000G Manual de usuario

DFI

DFI LanParty PRO875B Manual de usuario

DFI

DFI SU256-SCM Manual de usuario

DFI

DFI PW65 Series Manual de usuario

DFI

DFI CA64-SC Manual de usuario

DFI

DFI HM101-QM87 Manual de usuario

DFI

DFI AD72-SC Manual de usuario

DFI

DFI 945G-TMGF Manual de usuario

DFI

DFI CD101-N Manual de usuario

DFI

DFI LanParty LT X38 series Manual de usuario

DFI

DFI ICX610-C621A-000G Manual de usuario

DFI

DFI E586-ICP Manual de usuario

DFI

DFI P2XBL DE+ Manual de usuario

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario