DFI COM630-B Manual de usuario
COM630-B
System Board
User’s Manual
A01430151
Copyright
This publication contains information that is protected by copyright. No part of it
may be reproduced in any form or by any means or used to make any transfor-
mation/adaptation without the prior written permission from the copyright hold-
ers.
This publication is provided for informational purposes only. The manufacturer
makes no representations or warranties with respect to the contents or use
of this manual and specifically disclaims any express or implied warranties of
merchantability or fitness for any particular purpose. The user will assume the
entire risk of the use or the results of the use of this document. Further, the
manufacturer reserves the right to revise this publication and make changes to
its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
© 2011. All Rights Reserved.
Trademarks
All trademarks and registered trademarks of products appearing in this manual
are the properties of their respective holders.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission
limits.
Table of Contents
Copyright...........................................................................................2
Trademarks........................................................................................2
FCC and DOC Statement on Class B..............................................3
About this Manual .............................................................................6
Warranty ..........................................................................................6
Static Electricity Precautions.............................................................7
Safety Measures.................................................................................7
About the Package ............................................................................8
Before Using the System Board........................................................8
Chapter 1 - Introduction ..................................................................9
Specifications..................................................................................9
Chapter 2 - Hardware Installation.................................................. 11
System Board Layout .................................................................... 11
Jumper Settings............................................................................. 12
PS/2 Power Select.................................................................... 12
USB Power Select..................................................................... 13
Panel Power Select................................................................... 14
Power-on Select....................................................................... 15
CompactFlash Socket Setting..................................................... 16
Rear Panel I/O Ports..................................................................... 17
PS/2 Ports and S/PDIF Ports...................................................... 18
Serial (COM) Ports ................................................................... 19
VGA Port................................................................................. 20
RJ45 LAN Port ......................................................................... 21
Universal Serial Bus Connectors................................................. 22
Audio...................................................................................... 23
Internal I/O Connectors................................................................ 25
CD-in Internal Audio Connector ................................................. 25
S/PDIF Connector..................................................................... 26
LVDS LCD Panel Connector and LCD/Inverter Power Connector...... 27
Digital I/O Connector and Digital I/O Power Connector................. 29
Parallel Connector (optional)...................................................... 30
Floppy Disk Drive Connector...................................................... 31
SATA (Serial ATA) Connectors.................................................... 32
IDE Connector ......................................................................... 33
IrDA Connector........................................................................ 35
Cooling Fan Connectors............................................................. 36
Chassis Intrusion Connector ...................................................... 37
Power Connectors .................................................................... 38
Wake-On-Ring Connector .......................................................... 39
Standby Power LED.................................................................. 40
Front Panel Connectors............................................................. 41
GPIO Connector....................................................................... 42
Expansion Slots ....................................................................... 43
Battery ................................................................................... 44
CompactFlash Socket................................................................ 45
COM Express Connectors .......................................................... 46
1
6
Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual
in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board
Utility CD) will appear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the
product, inability to use the product, unauthorized replacement or alteration
of components and product specifications.
2. The warranty is void if the product has been subjected to physical abuse,
improper installation, modification, accidents or unauthorized repair of the
product.
3. Unless otherwise instructed in this user’s manual, the user may not, under
any circumstances, attempt to perform service, adjustments or repairs on the
product, whether in or out of warranty. It must be returned to the purchase
point, factory or authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial
damages to the product that has been modified or altered.
1
7
Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components
or devices even before installing them in your system unit. Static electrical dis-
charge can damage computer components without causing any signs of physical
damage. You must take extra care in handling them to ensure against electro-
static build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag
until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the compo-
nents, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold
modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and
other components. Perform the upgrade instruction procedures described
at an ESD workstation only. If such a station is not available, you can
provide some ESD protection by wearing an antistatic wrist strap and
attaching it to a metal part of the system chassis. If a wrist strap is
unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for instal-
lation or servicing. After installation or servicing, cover the system chassis
before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufac-
turer.
• Dispose of used batteries according to local ordinance.
1
8
Introduction
About the Package
The system board package contains the following items. If any of these items are
missing or damaged, please contact your dealer or sales representative for as-
sistance.
One system board
One USB port cable
One Serial ATA data cable
One Serial ATA power cable
One IDE cable
One FDD cable
One I/O shield
One QR (Quick Reference)
The system board and accessories in the package may not come similar to the
information listed above. This may differ in accordance to the sales region or
models in which it was sold. For more information about the standard package in
your region, please contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the
following internal components.
• A CPU
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will nor-
mally include at least a keyboard, a mouse and a video display monitor.
1
9
Introduction
Chapter 1 - Introduction
Specifications
Audio
Serial ATA
IDE
BIOS
(optional)
I/O Chip 1
I/O Chip 2
Damage Free
Intelligence
Temperature
Humidity
Rear Panel I/O
Ports
• Realtek ALC262 audio codec (ALC655 optional)
• 6-channel audio output
• SATA speed up to 3Gb/s
• Four SATA ports
• Supports up to Ultra ATA 100
• One IDE channel supports up to 2 IDE devices
• FWH/LPC interface
• Supports up to 4Mbit flash ROM
• PLCC32 socket
• Supports WP# jumper
• Carrier board ROM enable/disable function supported
• Winbond 83627HG-AW controller
• LPC interface
• Supports Smart fan
• Default I/O port address “2eh”
• Fintek F81216D controller
• LPC interface
• Supports 4 COM ports
• Supports IrDA
• Watchdog timer function
• Default I/O port address “4eh”
• Monitors system temperature and overheat alarm
• Monitors system fan speed and failure alarm
• Operating: 0oC to 60oC
• Storage: -20oC to 85oC
• Operating: 10% to 90%
• 1 mini-DIN-6 PS/2 mouse port
• 1 mini-DIN-6 PS/2 keyboard port
• 3 DB-9 serial ports
• 1 DB-15 VGA port
• 1 RJ45 LAN port
• 4 USB 2.0/1.1 ports
• Mic-in, line-in and line-out
1
10
Introduction
I/O Connectors
Expansion Slots
COM Express
Connectors
Dimensions
• 2 connectors for 4 additional external USB 2.0/1.1 ports
• 1 connector for an external serial port
• 1 LVDS LCD panel connector
• 1 LCD/inverter power connector
• 1 Digital I/O connector
• 1 Digital I/O power connector
• 1 front audio connector for line-out and mic-in jacks
• 1 CD-in internal audio connector
• 1 S/PDIF-in/out connector
• 1 GPIO connector
• 1 connector for IrDA interface
• 4 Serial ATA connectors
• 1 40-pin IDE connector
• 1 FDD connector
• 1 parallel connector (optional)
• 1 24-pin ATX power connector
• 1 4-pin 12V power connector
• 1 Wake-On-Ring connector
• 1 chassis open connector
• 1 front panel connector
• 3 fan connectors
• 1 diagnostic LED (optional)
• 1 CompactFlash socket
• 1 PCI Express x16 (Graphics or Dual SDVO)
• 2 PCI Express x1
• 4 PCI slots (PCI 2.3, 32-bit, 33MHz)
• Two 220-pin COM Express standard connectors
• Module connector pin: Tyco 3-631849-6
• Dimensions
- ATX form factor
- 305mm (12”) x 244mm (9.6”)
• Compliance
- PICMG COM Express R1.0, Type 2
Otros manuales para COM630-B
1
Tabla de contenidos
Otros manuales de Placa madre de DFI
DFI
DFI PB61-V3 Manual de usuario
DFI
DFI AK74-SC Manual de usuario
DFI
DFI C586VX/E Manual de usuario
DFI
DFI Blood-Iron LanParty Bi 785G-M35 Manual de usuario
DFI
DFI NS36-TC Manual de usuario
DFI
DFI CA33-SC Manual de usuario
DFI
DFI NF4 SLI INFINITY Manual de usuario
DFI
DFI PE11-TC Manual de usuario
DFI
DFI 915G-TMGF Manual de usuario
DFI
DFI NB72-SC Manual de usuario
DFI
DFI SB300-C Manual de usuario
DFI
DFI LanParty PRO875B Manual de usuario
DFI
DFI BT160 Manual de usuario
DFI
DFI LANPARTY DK X58-T3EH6 Manual de usuario
DFI
DFI ADS310-R680E/Q670E Manual de usuario
DFI
DFI AL102 Manual de usuario
DFI
DFI CA64-TC Manual de usuario
DFI
DFI PB50-ZX Manual de usuario
DFI
DFI MB331-CRM Manual de usuario
DFI
DFI MB330-CRM Manual de usuario
Manuales populares de Placa madre de otras marcas
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
Biostar
Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación
