DFI G4S306-C Manual de usuario

G4S306-C

Rev. A+

System Board

User’s Manual

935-G4S306-500G

A80210545

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®865G chipset

- Intel®865G Graphics Memory Controller Hub (GMCH)

- Intel®82801EB I/O Controller Hub (ICH5)

Processor

The system board is equipped with Socket 478 for installing one of

the following supported processors.

• Intel®Pentium®4 Processor with Hyper-ThreadingTechnology

- 800MHz/533MHz system data bus

• Intel®Pentium®4 Northwood processor

- 533MHz/400MHz system data bus

• Intel®Celeron®Northwood processor

- 400MHz system data bus

System Memory

• Two 184-pin DDR DIMM sockets

• Supports dual channel (128-bit wide) memory interface

• Supports up to 2GB system memory

• Synchronous operation with processor system bus

- PC2700/PC3200 (DDR333/DDR400) with 800MHz FSB

CPU. DDR333 will run at 320MHz memory frequency when

used with 800MHz FSB CPU.

- Use PC2100/PC2700 (DDR266/DDR333) with 533MHz

FSB CPU

- Use PC2100 (DDR266) with 400MHz FSB CPU

• Supports non-ECC (x64) DIMM using 128Mb, 256Mb or

512Mb

• Supports unbuffered DIMMs

Note:

When using DDR333/DDR400 with Celeron 400MHz FSB

CPU, the maximum speed will be limited to the speed of a

DDR266.

Chapter 1 - Introduction

Introduction

Density Width

Single/Double

184-pin DDR

64 Mbit

SS/DS

64/128MB

X16

SS/DS

32MB/NA

Density 128 Mbit

SS/DS

128/256MB

X16

SS/DS

64MB/NA

256 Mbit

SS/DS

256/512MB

X16

SS/DS

128MB/NA

512 Mbit

SS/DS

512/1024MB

X16

SS/DS

256MB/NA

Expansion Slots

• 1 AGP slot

• 3 PCI slots

AGP (Accelerated Graphics Port)

• Supports AGP 3.0 (AGP 4x and 8x) and AGP 2.0 (AGP 1x and

4x) spec.

• Supports 1.5V AGP 8x (2.13GB/sec.) and AGP 4x (1066MB/

sec.) add-in cards.

AGP is an interface designed to support high performance 3D

graphics cards for 3D graphics applications. It handles large

amounts of graphics data with the following features:

• Pipelined memory read and write operations that hide

memory access latency.

• Demultiplexing of address and data on the bus for nearly

100 percent efficiency.

Note:

AGP 2x and 3.3V AGP cards are not supported.

Onboard Graphics Features

• Graphics memory

- Shares 1MB/8MB/16MB of the system memory in DOS

mode

- Uses Dynamic Video Memory Technology (DVMT) in

Windows mode

• Graphics controller

- Core frequency of 266MHz

- 350MHz integrated 24-bit RAMDAC

Hardware Installation

2.1 System Board Layout

Chapter 2 - Hardware Installation

KB/Mouse

COM 1

Parallel

VGA

Socket 478

+12V power

USB 1-2

LAN, USB 3-4

Line-out/Line-in/Mic-in

Intel

82865G

Intel

ICH5

Realtek

RTL8101L

IrDA

COM 2

AGP

PCI 1

PCI 2

PCI 3

Game

CD-in

Audio

Codec

Front audio

S/PDIF

Surr_con

FDD

USB 5-6

USB 7-8 BIOS

SATA 2

SATA 1

Battery

Chassis

fan

IDE 1

IDE 2

DDR 1

ATX

power

CPU fan

2nd fan

WOL

DIMM LED

DDR 2

Winbond

W83627HF

PS/2 Power (JP4)

USB 1-4 Power

(JP5)

USB 5-8 Power

(JP6)

Clear CMOS (JP3)

HD-LED

RESET

SPEAKER

PWR-LED

ATX-SW

2Hardware Installation

COM 1

2.5.2 Serial Ports

The serial ports are RS-232C asynchronous communication ports

with 16C550A-compatible UARTs that can be used with modems,

serial printers, remote display terminals, and other serial devices.

The system board is equipped with an onboard serial port (CN4 -

Teal/Turquoise) for COM 1 and a 9-pin connector at location J6 for

COM 2.

One card-edge bracket, mounted with a serial port cable, will be

provided as an option. If you want to use the COM 2 serial port,

connect the serial port cable to connector J6. Make sure the colored

stripe on the ribbon cable is aligned with pin 1 of connector J6.

Mount the card-edge bracket to the system chassis.

BIOS Setting

Select the serial ports’ I/O address in the Integrated Peripherals

submenu (“Super IO Device” section) of the BIOS. Refer to chapter

3 for more information.

COM 2 19

TD RD

DTR

RTS DSR

CTS

Hardware Installation

2.6.3 S/PDIF Connector

The system board is equipped with a S/PDIF connector. One card-

edge bracket, mounted with S/PDIF ports, will be provided as an

option. Install the card-edge bracket to the system chassis then

connect the audio cable connector to J3. Make sure pin 1 of the

audio cable connector is aligned with pin 1 of J3.

VCC

Key

SPDIF out

GND

SPDIF in

2Hardware Installation

2.6.13 Front Panel Connectors

HD-LED: Primary/Secondary IDE LED

This LED will light when the hard drive is being accessed.

RESET: Reset Switch

This switch allows you to reboot without having to power off the

system thus prolonging the life of the power supply or system.

SPEAKER: Speaker Connector

This connects to the speaker installed in the system chassis.

ATX-SW:ATX Power Switch

Depending on the setting in the BIOS setup, this switch is a “dual

function power button” that will allow your system to enter the Soft-

Off or Suspend mode. Refer to “Soft-Off By PWR-BTTN” in the

Power Management Setup (Chapter 3).

J14

2122

PWR-LED

ATX-SW

HD-LED

RESET

SPEAKER

Hardware Installation

PWR-LED: Power/Standby LED

When the system’s power is on, this LED will light.When the system

is in the S1 (POS - Power On Suspend) or S3 (STR - Suspend To

RAM) state, it will blink every second.

Note:

If a system did not boot-up and the Power/Standby LED did

not light after it was powered-on, it may indicate that the CPU

or memory module was not installed properly. Please make

sure they are properly inserted into their corresponding socket.

HD-LED

(Primary/Secondary IDE LED)

Reserved

ATX-SW

(ATX power switch)

Reserved

RESET

(Reset switch)

SPEAKER

(Speaker connector)

PWR-LED

(Power/Standby LED)

Reserved

Key

Pin Assignment

HDD LED Power

HDD

N. C.

PWRBT+

PWRBT-

N. C.

Ground

H/W Reset

Speaker Data

N. C.

Ground

Speaker Power

LED Power (+)

LED Power (-) or Standby Signal

N. C.

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario