DFI NB76-BC Manual de usuario

NB76-BC

NB76-BL

Rev.A+

System Board User’s Manual

Carte Mère Manuel Pour Utilisateur

System-Platine Benutzerhandbuch

Manual del Usuario de Placas Base

935-NB7601-300

62300231

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98 SE, Windows®ME, Windows®2000, Windows NT®

4.0 and Windows®XP are registered trademarks of Microsoft

Corporation. Intel®and Pentium®4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Quick Setup Guide

Quick Setup

Guide

Table of Contents

Chapter 1

Quick Setup Guide.............................................

Chapter 2

English......................................................................

Chapter 3

Français (French).................................................

Chapter 4

Deutsch (German)................................................

Chapter 5

Español (Spanish)..................................................

NB76-BC/BL Intel 845G

AGP slot

“BL” supports onboard LAN and Smart I/O

Quick Setup Guide

Quick Setup

Guide

Chapter 1 - Quick Setup Guide

Table of Contents

1.1 System Board Layout..................................................................................................

1.2 Jumpers.....................................................................................................................................

1.3 Ports and Connectors................................................................................................

1.4 Award BIOS Setup Utility.......................................................................................

Note:

The user’s manual in the provided CD contains detailed information

about the system board. If, in some cases, some information doesn’t

match those shown in this manual, this manual should always be

regarded as the most updated version.

Quick Setup Guide

Quick Setup

Guide

1.1 System Board Layout

Mouse

CN4

COM 1

(CN2)

Parallel (CN6)

VGA (CN1)

Wake-On-KB/Mouse

(JP1)

+12V power

(ATXP1)

CN3

USB 1

USB 2

LAN

USB 3

USB 4

CN7

Line-out

Line-in

Mic-in

CN5

Game/MIDI

(J6)

I/O

chip

IrDA (J11)

AC’97

Front audio (J2)

Realtek

RTL8100

Socket 478

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

Intel

845G

GMCH

Intel

ICH4

CPU FSB

select (JP4)

Clear CMOS (JP7)

Wake-On-

LAN (J23)

Chassis

fan (J25)

Battery

CPU fan

(J18) Second

fan (J19)

ATX main

power (PL1)

DIMM

Standby

Power LED

FDD (J21)

IDE 2 (J22)

IDE 1

(J24)

Firmware

Hub

J20

PWR-LED

G-SW

RESET

SPEAKER

G-LED

HD-LED

Square denotes pin 1

ATX-SW

AGP Slot

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

PCI Slot 5

PCI Slot 6

CN3

Wake-On-USB KB

for USB 1/2/3/4 (JP9)

COM 2

(J13)

Wake-On-Ring (J12)

USB 5 & 6

(J14)

Wake-On-USB KB for

USB 5/6 (JP8)

CD-in (J8)

TAD (J7)

S/PDIF-out

(J1)

NB76-BL

(Supports onboard LAN)

Quick Setup Guide

Quick Setup

Guide

Note:

The illustrations on the following pages are based on the system

board that supports onboard LAN.

Mouse

CN4

COM 1

(CN2)

Parallel (CN6)

VGA (CN1)

Wake-On-KB/Mouse

(JP1)

+12V power

(ATXP1)

CN3

USB 1

USB 2

USB 3

USB 4

CN7

Line-out

Line-in

Mic-in

CN5

Game/MIDI

(J6)

I/O

chip

IrDA (J11)

AC’97

Front audio (J2)

Socket 478

DDR SDRAM

DIMM 1

DDR SDRAM

DIMM 2

Intel

845G

GMCH

Intel

ICH4

CPU FSB

select (JP4)

Clear CMOS (JP7)

Wake-On-

LAN (J23)

Chassis

fan (J25)

Battery

CPU fan

(J18) Second

fan (J19)

ATX main

power (PL1)

DIMM

Standby

Power LED

FDD (J21)

IDE 2 (J22)

IDE 1

(J24)

Firmware

Hub

J20

PWR-LED

G-SW

RESET

SPEAKER

G-LED

HD-LED

Square denotes pin 1

ATX-SW

AGP Slot

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

PCI Slot 5

PCI Slot 6

CN3

Wake-On-USB KB

for USB 1/2/3/4 (JP9)

COM 2

(J13)

Wake-On-Ring (J12)

USB5&6

(J14)

Wake-On-USB KB for

USB 5/6 (JP8)

CD-in (J8)

TAD (J7)

S/PDIF-out

(J1)

NB76-BC

Quick Setup Guide

Quick Setup

Guide

Warning:

Electrostatic discharge (ESD) can damage your system board,

processor, disk drives, add-in boards, and other components. Perform

the upgrade instruction procedures described at an ESD workstation

only. If such a station is not available, you can provide some ESD

protection by wearing an antistatic wrist strap and attaching it to a

metal part of the system chassis. If a wrist strap is unavailable,

establish and maintain contact with the system chassis throughout

any procedures requiring ESD protection.

Quick Setup Guide

Quick Setup

Guide

1.2 Jumpers

1.2.1 Clear CMOS Data - JP7

1-2 On:

Normal (default)

2-3 On:

Clear CMOS Data

Clear CMOS

(JP7)

1.2.2 Jumper Settings for Wake-On-Keyboard/Wake-On-

Mouse - JP1

Wake-On-

KB/Mouse (JP1)

1-2 On: Disable

(default)

2-3 On: Enable

If JP1 was enabled with a password set in the “KB Power On Password” field,

and now you wish to disable the keyboard password function, make sure to

set the “Keyboard/Mouse Power On” field to Disabled prior to setting JP1 to

disabled.You will not be able to boot up the system if you fail to do so.

Quick Setup Guide

Quick Setup

Guide

The power button will not function once a keyboard password has been set

in the “KB Power On Password” (“Onboard Super IO Device” field) of the

Integrated Peripherals submenu. You must type the correct password to

power-on the system.

The 5VSB power source of your power supply must support

≥

720mA.

1.2.3 Jumper Settings forWake-On-USB Keyboard

Wake-On-USB (KB)

1/2/3/4 (JP9)

Wake-On-USB

(KB) 5/6 (JP8)

123

2-3 On: Enable

(default)

1-2 On: Disable

123

JP8

JP9

123

JP8

JP9

If you are using the Wake-On-USB Keyboard function for 2 USB ports, the

5VSB power source of your power supply must support

≥

1.5A.

If you are using the Wake-On-USB Keyboard function for 4 or more USB

ports, the 5VSB power source of your power supply must support

≥

2A.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario