DFI NB32-SC Manual de usuario

NB32-SC

NB32-SL

Rev. A+

System Board

Users Manual

50300125

Copyri ht

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows® 98, Windows® 98 SE, Windows® ME, Windows® 000

and Windows NT® 4.0 are registered trademarks of Microsoft

Corporation. Intel® and Pentium® 4 are registered trademarks of

Intel Corporation. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This users manual contains detailed information about the system

board. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

System Board

This users manual is for the NB3 -SC and NB3 -SL system boards.

The differences between these boards are shown below.

NB32-SL

(Supports Onboard LAN)

Realtek RTL8100

RJ45 LAN

NB32-SC

Table of Contents

Chapter 1 - ntroduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware nstallation

.1 System Board Layout ..........................................................................................

. System Memory...........................................................................................................

.3 Jumper Settings for Clearing CMOS Data........................................

.4 Jumper Settings for Wake-On-Keyboard/Mouse..................................

.5 Jumper Settings for Wake-On-USB Keyboard................................

.6 Jumper Settings for USB 4................................................................................

.7 Ports and Connectors...........................................................................................

Chapter 3 - Award B OS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 CPU Frequency Control..................................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

ntroduction



Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4. Hardware Doctor..........................................................................................................

4.3 Intel 845 INF Update Utility for Windows 98/ 000/ME...

4.4 Audio Drivers and Software Application...............................................

4.5 Onboard LAN Drivers for Windows.......................................................

4.6 Microsoft DirectX 8.0 Driver.............................................................................

4.7 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B. Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist....................................................................................



ntroduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 Intel® 845 chipset

- Intel® 8 845 Memory Controller Hub (MCH)

- Intel® 8 801BA I/O Controller Hub (ICH )

Processor

The system board is equipped with Socket 478 for installing a

Pentium® 4 processor.

 Intel® Pentium® 4 processor (478-pin)

 400MHz system data bus

System Memory

 Three 168-pin PC SDRAM DIMM sockets

 Suppor ts 3GB system memory

- Uses 64Mbit, 1 8Mbit, up to 1.5GB using 56Mbit or up to

3GB using 51 Mbit technology, PC-100/PC-133 PC SDRAM

DIMM

 Supports ECC function

Chapter 1 - Introduction

D MMs

MBx64/x7

4MBx64/x7

8MBx64/x7

Memory Size

16MB

3 MB

64MB

D MMs

16MBx64/x7

3 MBx64/x7

64MBx64/x7

Memory Size

1 8MB

56MB

51 MB

ntroduction



Expansion Slots

The system board is equipped with 1 AGP slot, dedicated PCI

slots and 1 shared PCI/CNR slot.

The AGP slot only supports 1.5V AGP 4x (1066MB/sec. bandwidth)

add-in cards. AGP is an interface designed to support high

performance 3D graphics cards for 3D graphics applications. It

handles large amounts of graphics data with the following features:

 Pipelined memory read and write operations that hide memory

access latency.

 Demultiplexing of address and data on the bus for nearly 100

percent efficiency.

CNR (Communication and Networking Riser) is an interface that

supports multi-channel audio, V.90 analog modem, phone-line based

networking or 10/100 Ethernet based networking riser board.

Onboard Audio Features

 18-bit stereo full-duplex codec with independent variable sam-

pling rate

 High quality differential CD input

 True stereo line level outputs

Onboard LAN Features (NB32-SL)

 Uses Realtek RTL8100 fast ethernet controller

 Integrated IEEE 80 .3 10BASE-T and 100BASE-TX compatible

PHY

 3 -bit PCI master interface

 Integrated power management functions

 Full duplex support at both 10 and 100 Mbps

 Supports IEEE 80 .3u auto-negotiation

 Suppor ts wire for management

Compatibility

 Microsoft PC 98 compliant

 PCI . , CNR 1.0 A type and AC 97 compliant

 Intel AGP version .0



ntroduction

ATX Double Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One RJ45 LAN (NB3 -SL)

 Two NS16C550A-compatible DB-9 serial ports

 One SPP/ECP/EPP DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for additional external USB ports

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 Three ATX power supply connectors

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU fan, system fan and second fan connectors

 Two internal audio connectors (CD-in and TAD)

PC Bus Master DE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33, ATA/66 and ATA/100 hard drives

 PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

rDA nterface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

ntroduction



USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J8

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB por ts, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

B OS

 Award BIOS, Windows® 98/ 000/ME Plug and Play compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

Desktop Management nterface (DM )

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors CPU/system temperature and overheat alarm

 Monitors 5VSB/VBAT/3.3V/5V/±1 V/CPU voltages and failure

alarm

 Monitors the fan speed of CPU fan, system fan and second fan;

and failure alarm

 Automatic system fan and second fan on/off control

 Read back capability that displays temperature, voltage and fan

speed

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario