DFI G486VPB Manual de usuario

G486VPB

Rev. 0+

System Board

User’s Manual

-D28750815-

No part of this document may be copied, reproduced in

any form or by any means or used to make any transfor-

mation/adaptation without the prior written consent of

DFI, Inc.

DFI, Inc. makes no warranties with respect to this

documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular

purpose. The information in this document is subject to

change without notice. DFI, Inc. reserves the right to

make revisions to this publication and to make changes

to any and/or all parts of its content, at any time,

without obligation to notify any person or entity of such

changes. Further, DFI, Inc. assumes no responsibility

for any errors that may appear in this document.

DFI is a registered trademark, and G486VPB is a

trademark of Diamond Flower, Inc. All other product

names mentioned are trademarks or registered trade-

marks of their respective companies.

vFCC Statement on Class B

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

the receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modifications not expressly

approved by the party responsible for compliance

could void the user's authority to operate the

equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

PCI/ISASystemBoard

v Table of Contentsv

Introduction ........................................................................................6

Features and Specifications ...................................................... 7

Package Checklist ..................................................................... 9

Installation Overview ........................................................................10

Preparing the Area .............................................................................10

Handling the System Board .....................................................10

Tips in Handling the System Board ...............................11

Hardware Installation...............................................................12

Installation Procedures ..................................................12

Locations of Jumpers ..........................................13

Cache Configuration ............................................14

Jumper Setting for Cache Memory ...........16

CPU Installation ...................................................17

Jumpers for CPU Voltage Select ..............19

Jumpers for CPU External Clock Select...20

Jumpers for CPU Type Select ..................21

Installing Upgrade CPU .............................32

Memory Installation .............................................37

Installing the Modules ................................39

Other jumper settings (Internal Battery Select,

CMOS clean Select, EPROM Type,

PS/2 Mouse, CPU External Clock Speed

for PCI Slots, ECP DMA Channel Select) .40

Installing the System Board ................................45

Built-in Ports ........................................................47

Serial Ports ...............................................48

Parallel Ports .............................................49

Floppy Disk Drive Controller .....................51

IDE Hard Disk Interface ............................52

PS/2 Mouse Port .......................................55

Installing Expansion Cards ..................................56

G486VPB

Initial Setup Program .......................................................................57

Award BIOS CMOS Setup Utilities .....................................................58

Standard CMOS Setup .......................................................................58

BIOS Features Setup .....................................................61

Chipset Features Setup .................................................63

Power Management Setup .............................................64

PCI Configuration Setup ................................................65

Load BIOS Defaults .......................................................66

Load Setup Defaults ......................................................66

Password Setting ...........................................................67

Supervisor Password ...........................................67

User Password .....................................................68

IDE HDD Auto Detection ...............................................69

Save & Exit Setup ..........................................................70

Exit Without Saving ........................................................70

IDE Device Drivers ...........................................................................71

Troubleshooting Checklist ...............................................................72

Appendix A:Types of Modules ...............................................74

Appendix B:System Error Report ..........................................76

Appendix C:Memory & I/O Maps ...........................................81

Appendix D:PCI I/O Pin Assignments ...................................83

Appendix E:ISA I/O Pin Assignments ...................................84

Appendix F:Connector Pin Assignments .............................85

Appendix G:Award BIOS Hard Disk Table .............................95

PCI/ISASystemBoard

vIntroduction

The G486VPB system board offers several advanced

features integrated into the system board. Its design is

based on the new Peripheral Component Interconnect

(PCI) local bus and Industry Standard Architecture

(ISA) standards.

The G486VPB is an Energy Star compliant system

board that supports the Environmental Protection

Agency's Green PC requirements. It reduces energy

consumption by automatically turning off peripherals

when not in use.

The G486VPB system board supports a 237-pin Zero

Insertion Force (ZIF) CPU socket that allows users to

easily upgrade their CPUs. It also supports an optional

Flash EPROM for easy BIOS upgrades. Flash EPROM

is a memory chip for the storage of BIOS which can be

erased in bulk or modified using a software utility.

The G486VPB is equipped with four PCI slots, four ISA

slots (one shared PCI/ISA slot).

Equipped with one built-in VL-bus IDE connector and

one ISA IDE connector, the G486VPB system board can

control four drives and supports fast Mode 4 hard drives

and hard drives larger than 528MB under DOS. The

system board is also equipped with two serial ports, an

ECP/EPP parallel port, a floppy disk drive controller,

and one optional mini-DIN-6 connector for the PS/2

mouse.

The G486VPB can support 1MB to 128MB of memory

using 256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36,

8Mx36 and 16Mx36 72-pin SIM modules.

G486VPB

Processor

•5V CPUs

Intel 486SX/DX/DX2 (full series) and PentiumTM

OverDrive Processor

AMD 486DX/DXL/DXL2 (full series)

Cyrix 486SX/DX/DX2 (full series)

•3.3V CPUs

Intel 486DX4-75/100

AMD 486DX2-66/80NV8T

486DX4-75/100NV8T

486DX2-66/80 SV8B

486DX4-75/100 SV8B

Cyrix 486DX2V-50/66/80

486DX4-100

5x86-100

Chipset

•VIA - VT82C496G - system and cache controller

VT82C505 - Host to PCI bridge

VT82C406 - peripheral chip

Power Management

•Supports System Management Mode (SMM) and

CPU stopped clock

•Hardware provides flexible event-driven power

management scheme and easy CPU transition state:

Ready, Doze and Suspend

•Microsoft APM 1.1 compliant

•EPA Energy Star compliant design

Features and Specifications

PCI/ISASystemBoard

BIOS

•Award system BIOS (Flash EPROM optional)

•Supports IDE HDDs larger than 528MB under DOS

(LBA mode only)

•System and EGA/VGA BIOS shadow

Super I/O Interface and Fast IDE

•Two NS16C550 compatible serial ports

•One parallel port with EPP and ECP support

•Supports 360K, 720K, 1.2M, and 1.44MB floppy

drives

•Two fast IDE connectors:

Primary IDE connector provides a VL-bus IDE

interface to support up to two Mode 4

enhanced HDDs

Secondary IDE connector provides an ISA IDE

Interface to support an ATAPI compliant

CD-ROM or a tape drive

Cache Memory

•128KB, 256KB, or 512KB

•Supports Level 1 and Level 2 write-back/

write-through cache

Memory Onboard

•1MB to 128MB

•Two 72-pin SIMM sockets

•Supports memory parity check function

•Supports 256KBx36, 512KBx36, 1MBx36,

2MBx36, 4MBx36, 8MBx36 and 16MBx36 SIMMs

Expansion Slots

•Three PCI slots

•One shared PCI/ISA slot

•Three 16-bit ISA slots

G486VPB

CPU Socket

•237-pin ZIF socket (Intel Socket 3)

Board Dimensions

•22cm (8.58") x 22cm (8.58")

Baby AT form factor

PCB

•4 layers

Package Checklist

The G486VPB package contains the following items:

•The G486VPB system board

•The G486VPB user’s manual

•One IDE driver diskette

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port

cables

If any of these items are missing or damaged, please

contact your dealer or sales representative for assistance.

PCI/ISASystemBoard

vInstallation Overview

This chapter summarizes the steps in installing the

G486VPB system board into your system unit.

Preparing the Area

Before unpacking the system board, make sure the

location you have selected is relatively free of dust and

static electricity. Excessive exposure to dust, static

electricity, direct sunlight, excessive humidity, extreme

cold, and water can damage the operational capabilities

of your system board. Avoid placing the unit on soft

surfaces such as beds and carpeted floors which can

hinder air circulation. These areas also attract static

electricity which can damage some circuits on your

system board.

Make sure that the power source has a properly

grounded, three-pronged socket. It is essential that the

power connection be properly grounded for correct

functioning of your system board. For further protection,

we recommend that you use a surge suppressor. This

will protect the system board from damage that may

result from a power surge on the line.

Move items that generate magnetic fields away from

your system board, since magnetic fields can damage

your system board. Once you have selected the ideal

location, unpack the G486VPB system board carefully.

Handling the System Board

It is quite easy to inadvertently damage your system

board even before installing it to your system unit.

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario