DFI AZ30-TC Manual de usuario

AZ30-TC

AZ30-TL

Rev. A+

System Board

User’s Manual

67920432

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect

to the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use

or the results of the use of this document. Further, the manufac-

turer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person

or entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. AMD, AthlonTM XP, AthlonTM and DuronTM

are registered trademarks of Advanced Micro Devices, Inc. VIA®is a

registered trademark of VIA Technologies, Inc. Award is a registered

trademark of Award Software, Inc. Other trademarks and registered

trademarks of products appearing in this manual are the properties

of their respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery manufactur-

er’s

instructions.

Joystick or MIDI port:

• Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can radi-

ate radio frequency energy and, if not installed and used in accord-

ance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should al-

ways be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

System Board

This user’s manual is for the AZ30-TC and AZ30-TL system boards.

The only difference between these boards is the AZ30-TL system

board supports onboard LAN.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications.....................................................................

1.2 Package Checklist.........................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ...............................................................................

2.2 System Memory............................................................................................

2.3 CPU......................................................................................................................

2.4 Jumper Settings..............................................................................................

2.5 Rear Panel I/O Ports..................................................................................

2.6 I/O Connectors.............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System........................................................

3.1.1 Standard CMOS Features..................................................

3.1.2 Advanced BIOS Features...................................................

3.1.3 Advanced Chipset Features ............................................

3.1.4 Integrated Peripherals...........................................................

3.1.5 Power Management Setup.................................................

3.1.6 PnP/PCI Configurations........................................................

3.1.7 PC Health Status.....................................................................

3.1.8 Frequency/Voltage Control................................................

3.1.9 Load Fail-Safe Defaults.........................................................

3.1.10 Load Optimized Defaults...................................................

3.1.11 Set Supervisor Password....................................................

3.1.12 Set User Password.................................................................

3.1.13 Save & Exit Setup...................................................................

3.1.14 Exit Without Saving...............................................................

3.2 Updating the BIOS....................................................................................

Introduction

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface...........................................................

4.2 Drivers, Utilities and Software Applications..................................

4.3 Installation Notes...........................................................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function...............................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................

B.2 Error Messages...............................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist........................................................................

101

103

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA®chipset

- North bridge: VIA®KM266

- South bridge: VIA®VT8235CD

Processor

The system board is equipped with Socket-A for PGA processor. It

is also equipped with a switching voltage regulator that automatically

detects 1.100V to 1.850V.

• AMD AthlonTM XP 266MHz FSB

• AMD AthlonTM 200/266MHz FSB

• AMD DuronTM 200MHz FSB

Important:

To ensure proper boot up and operation of your system, you

must power-off the system then turn off the power supply’s

switch or unplug the AC power cord prior to replacing the CPU.

System Memory

• Two 184-pin DDR SDRAM DIMM sockets

• Supports up to 2GB memory using PC1600 (DDR200) or

PC2100 (DDR266) DDR SDRAM DIMM, 2.5V type

• L2 cache memory

- DuronTM processor: built-in 64KB Level 2 pipelined burst

cache

- AthlonTM XP / AthlonTM processor: built-in 256KB Level 2

pipelined burst cache

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

Expansion Slots

The system board is equipped with 1 AGP slot and 3 PCI slots.

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The universal

AGP slot supports AGP 2x with up to 533MB/sec. bandwidth and

AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics applica-

tions. AGP in this system board will deliver faster and better graph-

ics to your PC.

Onboard Graphics Features

• Integrated ProSavage8TM 2D/3D/Video accelerator

- Shares 8MB to 32MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- Full AGP 4x, including sideband addressing and execute

mode

- High quality DVD video playback

• 3D rendering features

- 32-bit true color rendering

- MPEG-2 video textures

• 2D hardware acceleration features

• Motion video architecture

Onboard LAN Features (AZ30-TL only)

• VIA®VT8235CD and Phy fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• PCI master interface

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

Introduction

Onboard Audio Features

• Uses Realtek 6-channel codec

• AC’97 2.2 extension compliant codec

• Supports Microsoft®DirectSound / DirectSound 3D

• AC’97 supported with full duplex, independent sample rate con-

verter for audio recording and playback

• S/PDIF-in/out interface

• 6-channel audio output

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to an

analog format. This prevents the quality of the audio signal from

degrading whenever it is converted to analog. S/PDIF is usually

found on digital audio equipment such as a DAT machine or audio

processing device.The S/PDIF connector on the system board sends

surround sound and 3D audio signal outputs to amplifiers and

speakers and to digital recording devices like CD recorders.

6-channel Audio

The 6-channel audio output function is supported by using the 4-

channel connector, the audio jacks at the rear panel and configuring

the audio driver. Please refer to chapters 2 and 4

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. The

IRDA (Infrared Data Association) specification supports data

transfers of 115K baud at a distance of 1 meter.

Introduction

USB Ports

The system board supports USB 2.0 and USB 1.1. USB 1.1

supports 12Mb/second bandwidth while USB 2.0 supports 480Mb/

second bandwidth providing a marked improvement in device

transfer speeds between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS

• CPU Overclocking function in 1MHz stepping

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play BIOS.

DMI, along with the appropriately networked software, is designed

to make inventory, maintenance and troubleshooting of computer

systems easier. Refer to chapter 4 for instructions on using the DMI

utility.

Rear Panel I/O Ports (PC 99 color-coded connectors)

• Two USB 2.0/1.1 ports

• One RJ45 LAN port (AZ30-TL only)

• One DB-9 serial port

• One DB-15 VGA port

• One DB-25 parallel port

• One mini-DIN-6 PS/2 mouse port

• One mini-DIN-6 PS/2 keyboard port

• One game/MIDI port

• Three audio jacks: line-out, line-in and mic-in

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario