DFI G586VPM Manual de usuario

G586VPM

Rev. C+

System Board

User’s Manual

- D25250731 -

No part of this document may be copied or reproduced

in any form or by any means without the prior written

consent of DFI, Inc.

DFI, Inc. makes no warranties with respect to this

documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular

purpose. The information in this document is subject to

change without notice. DFI, Inc. reserves the right to

make revisions to this publication and to make changes

to any and/or all parts of its content, at any time,

without obligation to notify any person or entity of such

changes. Further, DFI, Inc. assumes no responsibility

for any errors that may appear in this document.

DFI is a registered trademark, and G586VPM is a

trademark of Diamond Flower, Inc. All other product

names mentioned are trademarks or registered trade-

marks of their respective companies.

vFCC Statement on Class B

This equipment has been tested and complies with the

limits for a Class B digital device, pursuant to Part 15

of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference

when the equipment is operated in a residential installa-

tion. This equipment generates, uses, and can radiate

radio frequency energy, and if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. How-

ever, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures.

•Reorient or relocate the receiving antenna,

•Increase the separation between the equipment and

the receiver,

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected, or

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modification not expressly approved

by the party responsible for compliance could void

the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

v Table of Contentsv

Introduction ..............................................................................

Features and Specifications ................................................

Package Checklist ...............................................................

Installation Overview ..............................................................

Preparing the Area ..............................................................

Handling the System Board ................................................

Tips in Handling the System Board ..............................

Hardware Installation..........................................................

Memory Installation ......................................................

Installing the Modules ............................................

Board Configuration ......................................................

Jumper Settings for Display Type and PS/2

Mouse Port............................................................

Jumper Settings for PCI Slot 4 ..............................

Jumper Settings for Parallel Port ..........................

Cache Memory .............................................................

CPU Installation ............................................................

Operating Systems ................................................

Jumper Settings for CPU .......................................

Installing Upgrade CPUs .......................................

Built-in Ports ........................................................................

Serial Ports ...................................................................

PS/2 Mouse Port ..........................................................

Parallel Port ..................................................................

Floppy Disk Drive Connector ........................................

IDE Hard Disk Connector .............................................

Installing Expansion Cards .................................................

Installing the System Board ................................................

1-1

1-2

1-4

2-1

2-2

2-3

2-6

2-7

2-8

2-10

2-12

2-13

2-16

2-17

2-19

2-24

2-29

2-30

2-31

2-32

2-34

2-35

2-38

2-39

Initial Setup Program ..............................................................

Award BIOS CMOS Setup Utilities ......................................

Standard CMOS Setup .................................................

BIOS Features Setup ...................................................

Chipset Features Setup ................................................

Power Management Setup ..........................................

PCI Configuration Setup ...............................................

Load BIOS Defaults ......................................................

Load Setup Defaults .....................................................

Password Setting ..........................................................

IDE HDD Auto Detection ..............................................

HDD Low Level Format ................................................

Save & Exit Setup ........................................................

Exit Without Saving ......................................................

IDE Device Drivers ..................................................................

Troubleshooting Checklist .....................................................

Appendix A:Types of Modules ..............................................

Appendix B:System Error Report .........................................

Appendix C:Memory & I/O Maps ..........................................

Appendix D:PCI I/O Pin Assignments ..................................

Appendix E:ISA I/O Pin Assignments ..................................

Appendix F:Connector Pin Assignments ............................

Appendix G:Award BIOS Hard Disk Table ...........................

Appendix H:System Overview ..............................................

3-1

3-2

3-5

3-6

3-8

3-9

3-10

3-11

3-12

3-13

3-14

4-1

5-1

A-1

B-1

C-1

D-1

E-1

F-1

G-1

H-1

PCI/ISASystemBoard

vIntroduction

The G586VPM system board offers several advanced

features integrated into the system board. It supports two

320-pin Zero Insertion Force (ZIF) CPU sockets for

PentiumTM processors running at 75MHz, 90MHz,

100MHz, 120MHz or 133MHz frequency. These ZIF

sockets allow users to easily upgrade their CPUs. The

G586VPM also supports Flash EPROM for easy BIOS

upgrades. Flash EPROM is a memory chip for the

storage of BIOS which can be erased in bulk or modi-

fied using a software utility.

Equipped with two built-in Bus Master PCI IDE con-

nectors, the G586VPM system board can control four

drives and supports fast PIO Modes 3 and 4 hard drives

and hard drives larger than 528MB. When the Bus

Master DMA Mode 2 IDE is enabled, the CPU utiliza-

tion rate will be highly reduced, thus taking full advan-

tage of the dual processors capability. The system board

is also equipped with two NS16C550A-compatible

serial ports, an SPP/EPP/ECP parallel port, a floppy disk

drive controller, and one mini-DIN-6 connector for the

PS/2 mouse.

The G586VPM can be configured to 22 different

memory sizes ranging from 4MB to 512MB using

256KBx32/36, 512KBx32/36, 1MBx32/36, 2MBx32/36,

4MBx32/36, 8MBx32/36 or 16MBx32/36 non-parity/

parity SIM modules.

Note:

The revision of the 75/90/100MHz processor must be

revision C2 or later. 120MHz and 133MHz for dual

processors will be supported in future revisions. Please

contact Intel or your dealer for details.

1-1 uIntroduction

G586VPM

Features and Specifications

Processor

•Symmetric multiprocessor architecture

Primary: Intel’s Pentium

TM 75/90/100/120/133MHz

Secondary: Intel’s PentiumTM 75/90/100/120/133MHz

Chipset

•VLSI VL82C594 - system and cache controller

VLSI VL82C595 (2) - data buffer

VLSI VL82C597 - PCI bridge

Architecture

•Symmetric multiprocessor

•PCI/ISA

•Windows 95 compatible

Energy Efficient Design

•Highly efficient switching power circuit

•System Power Management supported

•CPU stopped clock control

•Microsoft/Intel APM v1.1 compliant

BIOS

•Award Flash BIOS

•Supports IDE HDDs larger than 528MB under DOS

(LBA mode only)

•Windows 95 Plug & Play compliant

Introduction u1-2

PCI/ISASystemBoard

Modular Cache Memory

•160-pin socket for cache module

•3.3V/5V asynchronous SRAM or 3.3V pipeline burst

SRAM

•256KB, 512KB or 1MB Buffered WT cache

•256KB and 512KB modules available

•32 byte or 64 byte line size to allow the useof optional

cache Tag RAM size

Multiprocessor Operating Systems

•Windows NT 3.1/3.5/3.51

•SCO Unix Open Desktop/Open Server 3.0 (MPX)

•OS/2 2.11

Memory

•Up to 512MB

•Eight 72-pin single and/or double density SIMM sockets

•256KBx32/36, 512KBx32/36, 1MBx32/36, 2MBx32/36,

4MBx32/36, 8MBx32/36 or 16MBx32/36 non-parity/parity

SIMMs

•60ns or 70ns fast page mode DRAM

Two PCI IDE Connectors

•CMD 646 Bus Master PCI IDE chip

•PIO Modes 3 and 4 Enhanced IDE

•Bus Master DMA Mode 2 IDE supported

•ATAPI IDE CD-ROM supported

Integrated I/O

•Two NS 16C550A-compatible high speed UARTs

•One SPP/EPP/ECP parallel port

•One 720K/1.2MB/1.44MB/2.88MB floppy controller

•PS/2 mouse and keyboard ports

•IrDA (infrared) TX/RX header

Serial interface compliant with IrDA and HPSIR

1-3 uIntroduction

G586VPM

Expansion Slots

•Three dedicated PCI slots

•One shared PCI/ISA slot

•Three dedicated 16-bit ISA slots

ZIF Socket

•Two 320-pin ZIF sockets (Intel Socket 5)

Board Dimensions

•33cm (12.87") x 22cm (8.58")

Baby AT form factor

Introduction u1-4

Package Checklist

The G586VPM package contains the following items:

•G586VPM system board

•G586VPM user’s manual

•One IDE driver diskette

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port

cables

If any of these items are missing or damaged, please

contact your dealer or sales representative for assistance.

PCI/ISASystemBoard

vInstallation Overview

This chapter summarizes the steps in installing the

G586VPM system board into your system unit. It also

includes a description of the area in which you must

work and directions for memory installation. Before

installing the system board, obtain the memory you plan

to install. Please refer to the memory chart on page 2-4

for the number and type of SIM modules needed for the

amount of memory you require.

Preparing the Area

Before unpacking the system board, make sure the

location you have selected is relatively free of dust and

static electricity. Excessive exposure to dust, static

electricity, direct sunlight, excessive humidity, extreme

cold and water can damage the system board. Avoid soft

surfaces such as beds and carpeted floors which can

hinder air circulation. These areas also attract static

electricity which can damage some circuits on your

system board.

Be sure that the power source has a properly grounded,

three-pronged socket. It is essential that the power

connection be properly grounded for correct functioning

of your system board. For further protection, we recom-

mend that you use a surge suppressor. This will protect

the system board from damage that may result from a

power surge on the line.

Move items that generate magnetic fields away from

your system board, since magnetic fields can also

damage your system board. Once you have selected the

ideal location, unpack the G586VPM system board

carefully.

2-1 uInstallation Overview

Otros manuales para G586VPM

Tabla de contenidos

Otros manuales de Placa madre de DFI

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario