Danfoss Type CFR Manual de usuario

RoomThermostat

User Guide

Type CFR

Temperature setting

Set room temperature on the thermostat dial.

On the right-hand side of the thermostat is a

function switch with 3 possible settings:

The room temperature will be as set

on the thermostat.

The control system must have a CFZ

programmer, put thermostat switch

into this position to engage the pro-

grammer. The temperature will be as

set on the room thermostat, but in ac-

cordance with the consumption pattern

entered.

The heating pattern in the programmer

can be overridden by moving the

switch to or .

The room temperature will be as set

on the thermostat less a setback of

5°C/9°F.

Limitation of the setting range

Behind the dial for temperature setting are two lock-

rings. These can be moved as shown if the thermo-

stat setting range is to be narrowed.

Warning: Changes or modifications to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

(70°F)

FCC ID: PGBTYPE-CFR , CAN 3934104209

This device complies with Part 15 of the FCC Rules and

with RSS-210 of Industry Canada:

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Setback

5°C (9°F)

088R0228

Li 3,6V/1,9Ah

088R0228 DKCD 03/01

Registration field in

CFM

RoomThermostat

Instructions for Installation

Type CFR

Each room thermostat has a unique ID number

preventing conflicts with other thermostats. A single

room thermostat is capable of regulating several

heating outputs, provided these outputs are assigned to

the thermostat.

Assigning thermostats to output(s)

-The installation cable between room thermostat and

CFM (fig. 1) must be connected in assigning each

thermostat to the respective output(s).

-IntheLED array the firstavailable position will flash.

Outputs already assigned will not be lit (fig. 2). By

pressing OK the thermostat will be assigned to that

output. If the room thermostat is to be assigned under

another lit output, scroll to the output bymeansof the+/-

keys,then press OK.

-When the installation cable is removed, the red LED

underneath the battery cover (fig. 1) will flash for at

least one minute (Test mode).

Removal of assigned thermostat

-It is not necessary to have the installation cable in

place when removing an assigned thermostat. Once a

thermostat has been removed, it may be reassigned to

another output.

-Removal of room thermostat is done by pressing OK

for 5 seconds, then the entire LED array will be lit.

Scroll to the specific room thermostat to be removed

with the +/- button,and press OK for 5 seconds. The

thermostat has now been removed.

Test of room thermostat

If a defect in a room thermostat is suspected, the fol-

lowing test may be carried out:

- Set the thermostat to the highest temperature.

- Move the function switch on the side of the room ther-

mostat to a new position.

- If the LED underneath the battery cover (fig. 1) flashes

quickly for 3 minutes, the room thermostat is OK.

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss DEVIreg 130 Manual de usuario

Danfoss

Danfoss TP9000 Si Manual de usuario

Danfoss

Danfoss TP75-RF Manual de usuario

Danfoss

Danfoss RMT-24 Manual de usuario

Danfoss

Danfoss TP5000 si range Manual de usuario

Danfoss

Danfoss BasicPlus2 Manual de usuario

Danfoss

Danfoss RET230P Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de funcionamiento

Danfoss

Danfoss ECtemp 531 Manual de usuario

Danfoss

Danfoss ECtemp 550 Manual de usuario

Danfoss

Danfoss RTW-RA Manual de usuario

Danfoss

Danfoss RET1001M Manual de usuario

Danfoss

Danfoss TP75 Manual de usuario

Danfoss

Danfoss DEVIreg Opti Manual de usuario

Danfoss

Danfoss FP715Si Manual de usuario

Danfoss

Danfoss TP75H Manual de funcionamiento

Danfoss

Danfoss FP975 Manual de usuario

Danfoss

Danfoss TP9000 Guía

Danfoss

Danfoss CET B-RF Instrucciones de funcionamiento

Danfoss

Danfoss RT 270 Manual de usuario

Danfoss

Danfoss ECtemp 610 Manual de usuario

Danfoss

Danfoss TP5001 series Manual de usuario

Danfoss

Danfoss 088L5130 Manual de usuario

Danfoss

Danfoss LX205T Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario