Danfoss RET2000 B Manual de usuario

MAKING MODERN LIVING POSSIBLE

RET2000 B/M/MS

Electronic digital thermostat with LCD

User Guide

Danfoss Heating

RET1000

For a large print version of these instructions

please call Marketing on 0845 121 7400.

Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other

printed material. All trademarks in this material are property of the respective companies.

Danfoss Heating 3

Thank you for buying a Danfoss product GB

RET1000

What is a room thermostat?

... an explanation for householders. A room thermostat simply switches

the heating system on and oﬀ as necessary. It works by sensing the

air temperature, switching on the heating when the air temperature

falls below the thermostat setting, and switching it oﬀ once this set

temperature has been reached.

Turning a room thermostat to a higher setting will not make the

room heat up any faster. How quickly the room heats up depends on

the design of the heating system, for example, the size of boiler and

radiators.

Neither does the setting aﬀect how quickly the room cools down.

Turning a room thermostat to a lower setting will result in the room

being controlled at a lower temperature, and saves energy.

Danfoss Heating 5

The heating system will not work if a timeswitch or programmer has

switched it oﬀ.

The way to set and use your room thermostat is to ﬁnd the lowest

temperature setting that you are comfortable with, and then leave it

alone to do its job. The best way to do this is to set the room thermostat

to a low temperature – say 18°C – and then turn it up by one degree

each day until you are comfortable with the temperature. You won’t

have to adjust the thermostat further. Any adjustment above this

setting will waste energy and cost you more money.

If your heating system is a boiler with radiators, there will usually

be only one room thermostat to control the whole house. But you

can have diﬀerent temperatures in individual rooms by installing

thermostatic radiator valves (TRVs) on individual radiators. If you don’t

have TRVs, you should choose a temperature that is reasonable for the

whole house. If you do have TRVs, you can choose a slightly higher

setting to make sure that even the coldest room is comfortable, then

prevent any overheating in other rooms by adjusting the TRVs.

Room thermostats need a free ﬂow of air to sense the temperature,

so they must not be covered by curtains or blocked by furniture.

Nearby electric ﬁres, televisions, wall or table lamps may prevent the

thermostat from working properly.

RET1000

Display

The LCD displays actual room temperature until the Λ or V button

is pressed more than once. To activate the unit’s backlight press

the Λ or V button once, if no further buttons are pressed the

backlight will remain on for 6 seconds.

Flame: shows when heating output is on (in heating mode only)

Standby: shows when unit is manual set to standby

Snowake: shows when cooling output is on (in cooling mode only)

Battery: ashes when battery is low (battery units only)

Padlock: indicates keyboard lock has been set at installation

Temperature

Danfoss Heating 7

Setting the temperature

Press either the Λ or V buttons, the product backlight will come

on.

Press either the Λ or V button again within 6 seconds, the display

will ﬂash with the current set temperature. While the display is

ﬂashing press the Λ arrow to increase the set temperature to the

required setting or the V arrow to decrease the set temperature.

If no buttons are pressed the display will return to actual

temperature after 4 seconds and the backlight will go out after

6 seconds.

RET1000

Thermostat status (cool mode only)

A snowﬂake symbol will be lit whenever the thermostat is calling

for cooling. If this is seen to ﬂash, the thermostat output is

delayed for a short period to prevent compressor damage.

Thermostat status (heat mode only)

A ﬂame symbol will be lit whenever the thermostat is calling for

heat.

Danfoss Heating 9

Thermostat standby

To place the thermostat into standby (oﬀ), press the V arrow

twice to enter the temperature setting mode. When in heating

mode press and hold the V arrow until the set temperature

disappears and the standby symbol appears. In cooling mode

press and hold the Λ arrow until the standby symbol appears.

When in standby the thermostat will have no control of the

heating or cooling system.

To exit standby press and hold the Λ arrow (V arrow in cooling

mode) until the required set temperature is ﬂashing on the

display.

RET1000

Low Battery Indications (RET2000B)

For battery powered thermostat (RET2000B) when the batteries

require replacement the battery low symbol will ﬂash. Batteries

should be replaced within 15 days, after which the thermostat

will turn oﬀ the load it is controlling. If the power LED does

not illuminate when the dial is turned the batteries may have

expired and should be replaced immediately to avoid damage

to the thermostat

Otros manuales para RET2000 B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss ECA 30 Manual de usuario

Danfoss

Danfoss FH-RT Manual

Danfoss

Danfoss BasicPlus2 WT-D Manual de usuario

Danfoss

Danfoss EFET 160 Manual de usuario

Danfoss

Danfoss DEVIreg 132 Manual de usuario

Danfoss

Danfoss DEVIreg Opti Manual de usuario

Danfoss

Danfoss ECL Comfort 310 Manual de usuario

Danfoss

Danfoss TP6000M Manual de usuario

Danfoss

Danfoss REPI Series Manual de usuario

Danfoss

Danfoss CF-RP 088U0211 Manual de usuario

Danfoss

Danfoss ECL Comfort 310, P314 Manual de usuario

Danfoss

Danfoss TRONE-RF Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss TP5001 series Manual de usuario

Danfoss

Danfoss DEVIreg Smart Manual de usuario

Danfoss

Danfoss RET2001 Manual de usuario

Danfoss

Danfoss KP 61 Manual de usuario

Danfoss

Danfoss TP9 Manual de usuario

Danfoss

Danfoss Basic Plus2 Manual de usuario

Danfoss

Danfoss TP75-RF Manual de usuario

Danfoss

Danfoss ECtemp 531 Manual de usuario

Danfoss

Danfoss TP75M Manual de usuario

Danfoss

Danfoss TPOne-M Manual de usuario

Danfoss

Danfoss TP9000 Si Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario