Danfoss ECtemp 530 Manual de usuario

Danfoss ECtemp 530

Electronic Thermostat

Installation Guide

electricheating.danfoss.com

Danfoss ECtemp 530

3Installation Guide

1 Introduction

ECtemp 530 is an electronic thermostat provided with a

2- pole switch and a wire sensor to measure and control the

desired oor temperature. It can be either ush-mounted

(standard) or surface-mounted (using special box).

The thermostat has a button for adjusting the temperature

setting with a scale from ( ) 1 to 6 (each step corresponds

to approximately 8 °C). Furthermore, it has a LED indicator

showing standby periods (green light) and heating periods

(red light).

More information on this product can also be found at:

ectemp.danfoss.com

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Technical Specications . . . . . . . . . . . . 4

1.2 Safety Instructions . . . . . . . . . . . . . . . . 5

2 Mounting Instructions . . . . . . . . . . . . . . . . . 7

3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Disposal Instruction . . . . . . . . . . . . . . . . . 12

Danfoss ECtemp 530

Installation Guide4

1.1 Technical Specications

Operation voltage 220-240 V~, 50 Hz

Standby power consump-

tion Max 0.25 W

Relay:

Resistive load

Inductive load

Max 15 A / 3450 W @ 230 V

cos φ= 0.3 max 1A

Sensing units NTC 15kOhm at 25°C

Sensing values:

0 °C

25 °C

50 °C

42 kOhm

15 kOhm

6 kOhm

Hysteresis ± 0.4 °C

Ambient temperature -10 to +30 °C

Frost protection tempera-

ture 5 °C -

Temperature range ( ) 5-45°C with oor sen-

sor only

Cable specication max 1x4 mm² or 2x2,5 mm²

Ball pressure temperature 75 °C

Pollution degree 2 (domestic use)

Danfoss ECtemp 530

5Installation Guide

Type 1C

Storage temperature -20 to +65 °C

IP class 31

Protection class Class II -

Dimensions 85 x 85 x 36 mm

Weight 90 g

The product complies with the EN/IEC Standard «Automatic

electrical controls for household and similar use»:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1.2 Safety Instructions

Make sure the mains supply to the thermostat is turned o

before installation.

IMPORTANT: When the thermostat is used to control a

oor heating element in connection with a wooden oor or

similar material, always use a oor sensor and never set the

maximum oor temperature to more than 35 °C.

Danfoss ECtemp 530

Installation Guide6

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualied installer according to local

regulations.

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• The sensor is to be considered as live voltage. Have

this in mind if the sensor must be extended.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water,

dust, and excessive heat.

Danfoss ECtemp 530

7Installation Guide

2 Mounting Instructions

Place the thermostat at a suitable height on

the wall (typically 80-170cm.).

In wet rooms, place the thermostat accord-

ing to local regulation on IP classes.

Note: A oor sensor enables a more accurate

temperature control and is recommended in

all oor heating applications and mandatory

under wooden oors to reduce the risk of

over-heating the oor.

• Place the oor sensor in a conduit in an appropriate

place where it is not exposed to sunlight or draft from

door openings.

• Equally distant and >2cm from two heating cables.

• The conduit should be ush with the oor surface -

countersink the conduit if necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must be min 50mm.

Danfoss ECtemp 530

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

devireg™550

• Press the release tab in the bottom of the ther-

mostat using a at object.

• Carefully detach the front cover.

• Carefully detach the frame.

Danfoss ECtemp 530

9Installation Guide

2. Connect the thermostat according to the connection

diagram.

IP31

-10T30

D530

Mains

220-240V~

Max. Load

15 (1) A

Sensor

NL NTC

LOAD

-5°C

9

By connecting an external timer to the terminal

marked by a moon symbol (and by using for example

the same phase as for the mains power supply), the

thermostat can be set to reduce the temperature by

5 °C during specied periods.

The screen of the heating cable must be connected

to the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the oor sensor in a conduit in

the oor.

Danfoss ECtemp 530

Installation Guide10

3. Mount and reassemble the thermostat.

• Fasten the thermostat to a socket or an exterior

wall box by driving the screws through the holes in

each side of the thermostat.

• Install the frame and front cover in the reverse

order of disassembly.

4. Turn on the power supply.

3 Settings

How to change the minimum and maximum oor

temperatures

1. Remove the adjust-

ment button.

2. Move the pins to the

desired positions.

3. Put the adjustment

button back in place.

devireg™550

Note: Please be aware of the following:

• The oor temperature is measured where the oor

sensor is placed.

• The temperature of the bottom of a wooden oor can

be up to 10 degrees higher than the top.

Otros manuales para ECtemp 530

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss TP5000 RF Si Guía

Danfoss

Danfoss TP7000 Series Manual de usuario

Danfoss

Danfoss GreenCon RC-T2 Manual de usuario

Danfoss

Danfoss RT1 Instrucciones de montaje

Danfoss

Danfoss DEVIreg Opti Manual de usuario

Danfoss

Danfoss Icon Wireless Dial Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss RT 103 Manual de usuario

Danfoss

Danfoss REP24 Manual de usuario

Danfoss

Danfoss DEVIreg 330 Manual de usuario

Danfoss

Danfoss DEVIreg Room 140F1161 Manual de usuario

Danfoss

Danfoss ECtemp Touch Manual de usuario

Danfoss

Danfoss RET 230 HCW-3 Manual de usuario

Danfoss

Danfoss RT52 Manual de usuario

Danfoss

Danfoss RT 101 Manual de usuario

Danfoss

Danfoss ECtemp 550 Manual de usuario

Danfoss

Danfoss ECtemp Smart Manual de usuario

Danfoss

Danfoss HC6000 Manual de usuario

Danfoss

Danfoss RET2000 B Manual de usuario

Danfoss

Danfoss TP75-RF Manual de usuario

Danfoss

Danfoss RAS-C2 Combi Manual de usuario

Danfoss

Danfoss EFIT 550 Manual de usuario

Danfoss

Danfoss ECL Comfort 310 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario