Danfoss ECtemp 316 Manual de usuario
Danfoss ECtemp 316
3Installation Guide
1 Introduction
ECtemp 316 is an electronic thermostat to be installed in
electric cabinets with DIN rail attachment. The thermostat
must be installed via an all-pole disconnection switch.
ECtemp 316 applies to the control of room temperature,
oor temperature, ventilation, cooling or to the control of
snow melting in gutters and similar installations.
For measuring purposes either a wire sensor or an external
air sensor is used.
Table of Contents
1 Introduction � � � � � � � � � � � � � � � � � � � � � � � 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions � � � � � � � � � � � � � � � � � 6
3 Settings � � � � � � � � � � � � � � � � � � � � � � � � � � 8
3.1 Hysteresis . . . . . . . . . . . . . . . . . . . . . 8
3.2 Minimum Temperature Limiter . . . . . . . . 8
3.3 Temperature Set-back. . . . . . . . . . . . . . 9
4 Warranty� � � � � � � � � � � � � � � � � � � � � � � � � 10
5 Disposal Instruction � � � � � � � � � � � � � � � � � 12
Danfoss ECtemp 316
Installation Guide4
The thermostat has a button to adjust the temperature
setting with a scale from -10 °C to +50 °C . An LED indicator
shows standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
ectemp�danfoss�com
1�1 Technical Specications
Operation voltage 220-240 V~, 50 Hz
Standby power consumption Max 0.25 W
Relay:
Resistive load
Inductive load
Max 16 A / 3680 W @ 230 V
cos φ= 0.3 max 1 A
Sensing units NTC 15kOhm at 25 °C
Sensing values:
0°C
25°C
50°C
42 kOhm
15kOhm
6 kOhm
Hysteresis 0 to 6 °C
Ambient temperature 10 °C to +45 °C
Lowering in economy periods 0 to 8 °C
Temperature range -10 °C to +50 °C
Minimum temperature range -10 °C to +5 °C
Cable specication max 1x4 mm or 2x2,5 mm
Danfoss ECtemp 316
5Installation Guide
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1B
Storage temperature -20°C to +65°C
IP class 30
Protection class Class II -
Dimensions 86 x 36 x 58 mm
Weight 180 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/CEI 60730-1 (general)
• EN/CEI 60730-2-9 (thermostat)
1�2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35 °C.
Danfoss ECtemp 316
Installation Guide6
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water, dust,
and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
• Install the thermostat in an electric cabinet with DIN
rail attachment or a separate DIN attachment accord-
ing to local regulation on IP classes.
• Do not place the thermostat in a way that it will be
exposed to direct sunlight.
Danfoss ECtemp 316
7Installation Guide
Follow the steps below to mount the thermostat:
1. Click the thermostat on to the DIN rail attachment.
2. Connect the thermostat according to the connection
diagram.
IP20
-10T50 D316
121110987
L
654321 N
Mains
220-240V~
250V~
16 (1) A
SensorMin.
Danfoss A/S
Ulvehavevej 61
7100 Vejle
Denmark
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: When you use the wire sensor for oor heating,
always install the sensor in a conduit.
3. Turn on the power supply.
Protective separation
The thermostat is designed so that the sensor circuit is gal-
vanically separated from the high voltage part which means
that the sensor part is regarded as a low voltage part.
Danfoss ECtemp 316
Installation Guide8
3 Settings
A Night set-back
B Minimum temperature
limiter
C Hysteresis
3�1 Hysteresis
When the thermostat is used to apply with either heat-
ing systems or refrigerating systems, and the requested
temperature is between -10 °C to +50 °C, then it is recom-
mendable also to adjust the hysteresis Caccording to the
requested regulating range.
As an example if the temperature is set at 18 °C and the hyster-
esis at 3 °C the thermostat will switch on at 18 °C and o at 21 °C.
For controlling of room temperature the Hysteresis is rec-
ommended to the set point of 1 °C.
3�2 Minimum Temperature Limiter
When the thermostat is used in connection with snow and
ice melting systems, it is recommendable also to use and
adjust the minimum temperature limiter (B) which ensures
Danfoss ECtemp 316
9Installation Guide
both an upper and lower temperature range in between
which the thermostat allows the system to heat.
The requested maximum temperature range has to be
between -10 °C to +50 °C and the requested minimum
temperature range has to be between -10 °C to +5 °C.
An link between terminal 9+10 must be connected to acti-
vate the use of the minimum temperature feature when the
thermostat controls snow and ice melting in gutters, valley
gutters and down pipes, where the waste of unnecessary
energy must be avoided. In particular by extremely cold
weather where owing water or moisture does not occur.
When the temperature drops below the minimum tem-
perature set value, the thermostat stops heating and the
LED indicator turns yellow.
When the temperature exceeds the maximum temperature
setting, the thermostat stops heating and both the indica-
tor for minimum and maximum temperature disappears.
3�3 Temperature Set-back
By connecting an external timer to terminals 4 and 6, the
thermostat can be set to reduce the temperature by 0 °C to
8 °C (A).
Danfoss ECtemp 316
Installation Guide10
4 Warranty
A 2-year product warranty is valid for:
• thermostats: ECtemp 316.
Should you, against all expectations, experience a problem with your Danfoss
product, you will nd that Danfoss oers Danfoss warranty valid from the date
of purchase on the following conditions: During the warranty period Danfoss
shall oer a new comparable product or repair the product if the product is
found to be faulty by reason of defective design, materials or workmanship. The
repair or replacement.
The decision to either repair or replace will be solely at the discretion of Dan-
foss. Danfoss shall not be liable for any consequential or incidental damages
including, but not limited to, damages to property or extra utility expenses. No
extension of the warranty period following repairs undertaken is granted.
The warranty shall be valid only if the WARRANTY CERTIFICATE is completed
correctly and in accordance with the instructions, the fault is submitted to the
installer or the seller without undue delay and proof of purchase is provided.
Please note that the WARRANTY CERTIFICATE must be lled in, stamped and
signed by the authorized installer performing the installation (Installation
date must be indicated). After the installation is performed, store and keep the
WARRANTY CERTIFICATE and purchase documents (invoice, receipt or similar)
during the whole warranty period.
Danfoss warranty shall not cover any damage caused by incorrect conditions of
use, incorrect installation or if installation has been carried out by non-author-
ized electricians. All work will be invoiced in full if Danfoss is required to inspect
or repair faults that have arisen as a result of any of the above. The Danfoss
warranty shall not extend to products which have not been paid in full. Danfoss
will, at all times, provide a rapid and eective response to
all complaints and inquiries from our customers.
The warranty explicitly excludes all claims exceeding the
above conditions.
For full warranty text please use QR code
Tabla de contenidos
Otros manuales de Termostato de Danfoss
Danfoss
Danfoss Icon Master Manual de usuario
Danfoss
Danfoss 102E7 Instrucciones de montaje
Danfoss
Danfoss KP Series Manual de usuario
Danfoss
Danfoss GreenCon RC-T2 Manual de usuario
Danfoss
Danfoss HCS6101-3 Instrucciones de uso
Danfoss
Danfoss FHV-R Manual de usuario
Danfoss
Danfoss ECL Comfort 310, A333 Manual de usuario
Danfoss
Danfoss 088U0215 Manual de usuario
Danfoss
Danfoss living connect Manual de usuario
Danfoss
Danfoss C67 Manual de usuario
Danfoss
Danfoss KP 61 Manual de usuario
Danfoss
Danfoss RET 230 HCW-3 Manual de usuario
Danfoss
Danfoss TP5000 RF Si Guía
Danfoss
Danfoss RET1000 MD Manual de usuario
Danfoss
Danfoss RTD 3120 Manual de usuario
Danfoss
Danfoss HP8211-1RJ Manual de usuario
Danfoss
Danfoss WP75-RF Manual de usuario
Danfoss
Danfoss HC75-3 Manual de funcionamiento
Danfoss
Danfoss TP9 Manual de usuario
Danfoss
Danfoss SH-E01 Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
