CYP CH-527RXVBD Manual de usuario
CH-527RXVBD
4K UHD+ HDMI over HDBaseT Receiver
with Bi-directional 24V PoC
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document are
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
• Please completely disconnect the power when the unit is not in
use to avoid wasting electricity.
VERSION HISTORY
REV. DATE SUMMARY OF CHANGE
VS1 2018/12/22 Final technical review
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 IR Cable Pinouts ........................................ 5
6.4 RS-232 Bypass Pinout................................. 5
7. Connection Diagram ......................................6
8. Specications ..................................................7
8.1 Basic Specications .................................. 7
8.2 Video Specications................................. 8
8.3 Audio Specications................................. 9
8.4 Cable Specications .............................. 10
8.5 HDBaseT Features.................................... 11
9. Acronyms .......................................................12
1
1. INTRODUCTION
This HDMI over HDBaseT Receiver is a great solution for extending
UHD video and audio as well as Ethernet and control via a single run
of Cat.5e/6/7 cable over distances up to 100 meters. This extender
complies with the advanced HDCP 2.2 and HDMI 2.0 standards, as
well as supporting the legacy HDCP 1.x and HDMI 1.x standards. In
addition, despite HDBaseT’s 10.2Gbps bandwidth limitation, 4K UHD
HDMI video sources, up to and including 4K@60Hz (4:4:4, 8-bit) as
well as 10/12-bit sources with HDR, are able to be processed and
extended by the use of AVLC (Adaptive Visually Lossless Compression)
when needed. Multiple data and control interfaces are also able to
be extended, including IR, RS-232, and LAN connections.
This unit supports bi-directional 24V PoC (Power over Cable) allowing
the system to be completely powered by, or provide power to, a
compatible connected Transmitter, allowing for greater exibility
within different installation scenarios.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×HDMI to HDBaseT Receiver with Bi-directional 24V PoC
• 1×3.5mm to IR Extender Cable
• 1×Operation Manual
2
4. SYSTEM REQUIREMENTS
• HDMI receiving equipment such as an HDTV, monitor or audio
amplier.
• An HDBaseT Transmitter equipped with AVLC and 24V PoC support
is strongly recommended.
• The use of “Premium High Speed” HDMI cables, and industry
standard Cat.6, Cat.6a or Cat.7, is highly recommended.
5. FEATURES
• HDMI with HDR, 3D & 4K@60Hz support, DVI 1.0 compatible
• HDCP 1.x and HDCP 2.2 compliant
• Supports up to 4K UHD (18Gbps, 4K@50/60Hz 4:4:4, 8-bit) video input
and output
• Supports Deep Color input and output up to 12-bit
• Supports 10-bit and 12-bit HDR (High Dynamic Range) input/output
• Supports CEC bypass
• HDBaseT feature support: HD Video and Audio, 100BaseT Ethernet,
24V PoC and Control (bi-directional IR/RS-232 pass-through)
• HDBaseT input receives video, audio and data over a single
Cat.5e/6/7 cable and can reach distances up to 100m/328ft at 4K
when using Cat.6a/7
• Integrated AVLC (Adaptive Visually Lossless Compression) activates
when the bandwidth requirements of the source are beyond
10.2Gbps (340MHz) allowing for support of sources up to 18Gbps
(600MHz) with no loss of visual quality
• Supports pass-through of many audio formats including LPCM
2.0/5.1/7.1, Bitstream, and HD Bitstream
• Bi-directional 24V PoC allows the unit to be powered by, or provide
power to, a compatible connected Transmitter
Note: The 24V PoC function is designed to power, or receive power
from, compatible Transmitter units only. Non-PoC Transmitters will
need their own power supply. Other brands of Transmitter may not be
compatible.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
RS-232
POWER
ISP
LAN
STD
UPDATE
SYNC
1 2 3 4 5
1ISP Pinhole: This button is reserved for factory use only.
2STD/UPDATE Switch: This switch is reserved for factory use only.
Note: This should be left on the default setting of “STD” for normal
operation.
3RS-232 Port: Connect to a PC, laptop, or serial controllable device
for the extension of RS-232 signals between both ends of the
HDBaseT connection.
4LAN Port: Connect to an Ethernet supporting device or to your
local network, as appropriate, to extend the network to both ends
of the HDBaseT connection.
5POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
SYNC LED: This LED will illuminate when a live input source is
detected.
4
6.2 Rear Panel
HDMI OUT
CAT5e/6/7
IN
IR
EXTENDER
IR
BLASTER
DC 24V
+
-
1 2 3 4 5
1DC 24V Terminal Block: Plug the 24V DC power adapter into this
terminal block and connect it to an AC wall outlet for power.
(Optional)
Note: This connection is not required if the unit is receiving power
via 24V PoC from the Transmitter.
2IR BLASTER Port: Connect to an IR Blaster to transmit IR signals from
the other end of the HDBaseT connection to devices within direct
line-of-sight of the IR Blaster.
3IR EXTENDER Port: Connect to the provided IR Extender to receive
IR control signals and extend them to devices connected to the
other end of the HDBaseT connection. Ensure that the remote
being used is within direct line-of-sight of the IR Extender.
4CAT5e/6/7 IN Port: Connect to a compatible HDBaseT Transmitter
with a single Cat.5e/6/7 cable for transmission of all data signals.
24V PoC can also be supplied to, or received from, a connected
compatible Transmitter.
Note: The 24V PoC function is designed to power, or receive power
from, compatible Transmitter units only. Non-PoC Transmitters will
need their own power supply. Other brands of Transmitter may not
be compatible.
5HDMI OUT Port: Connect to an HDMI TV, monitor, or amplier for
digital video and audio output.
5
6.3 IR Cable Pinouts
IR Blaster
Cabl
e
1
2
3
Infrared
Power
Not U
sed
IR Extender
Cabl
e
1
2
3
Infr
ared
Power
Ground
6.4 RS-232 Bypass Pinout
DCD
RxD
TxD
DTR
GND
RI
CTS
RTS
DSR
1
2
3
4
5
8
7
6
9
DE-9 Male
Port
Tabla de contenidos
Otros manuales de Receptor de CYP
CYP
CYP CA-USBAT Manual de usuario
CYP
CYP CA-USBST Manual de usuario
CYP
CYP CH-517RXHS Manual de usuario
CYP
CYP CH-1529RXPLV Manual de usuario
CYP
CYP CH-2538TXWPKD Manual de usuario
CYP
CYP CRS-232 Manual de usuario
CYP
CYP PU-DVI1109TX Manual de usuario
CYP
CYP 5-Play HDBaseT PU-507WPRX Manual de usuario
CYP
CYP Dante AU-DTO4-RX Manual de usuario
CYP
CYP CH-316TX Manual de usuario
CYP
CYP PUV-1830RX-AVLC Manual de usuario
CYP
CYP CPLUS-21FRX Manual de usuario
CYP
CYP PU-606PLBD-TX Manual de usuario
CYP
CYP CH-514RXWPL Manual de usuario
CYP
CYP PU-607BDWP-RX Manual de usuario
CYP
CYP CH-2540RX Manual de usuario
CYP
CYP CH-507RXWP Manual de usuario
CYP
CYP AVX-101C-KIT Manual de usuario
CYP
CYP IP-A750RX Manual de usuario
CYP
CYP 5Play PUV-1650TX Manual de usuario
