CYP CH-316TX Manual de usuario
DRAFT
CH-316TX & CH-316RX
HDMI/USB/RS-232 & IR over single CAT5e/6
Transmitter and Receiver
Operation Manual
Operation Manual
DRAFT
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2009 by Cypress Technology.
All Rights Reserved.
Version 1.0 October 2009
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
DRAFT
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 17/02/14 Preliminary Release
DRAFT
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 1
6. Operation Controls and Functions....... 2
6.1 Transmitter Front Panel ....................2
6.2 Transmitter Rear Panel.....................3
6.3 Receiver Front Panel........................4
6.4 Receiver Rear Panel ........................5
6.5 RS-232 Protocols ...............................6
6.6 IR Cable Pin Dene ..........................6
6.7 WebGUI.............................................7
7. Connection Diagram .......................... 14
8. Specications ...................................... 15
9. Acronyms ............................................. 18
DRAFT
1
1. INTRODUCTION
The Transmitter (TX) and Receiver (RX) units allow you to extend Hi-
Denition video and audio to long distance over single CTA5e/CAT6
or through Ethernet TCP/IP network. IR and RS-232 protocols are also
channeled by the same extension, so it can provide versatile remote
control features. Further, both TX and RX carry an additional analog
audio IN/OUT ports for extra audio application. The 4-port USB hub on
the RX unit can communicate with the sole USB port on the TX unit and
send data or peripheral device sharing.
2. APPLICATIONS
• HDMI, USB, Audio, RS-232 & IR Extender
• Broadcasting system over single CAT5e/6
• Multimedia display and multi-data sharing
• Long distance data sending with cascade
• Matrix network system
• System control over RS-232 and equipment control over IR
• KVM control
3. PACKAGE CONTENTS
• HDMI/USB/RS-232/IR over single CAT5e/6 Transmitter
• HDMI/USB/RS-232/IR over single CAT5e/6 Receiver
• 5V/2.6A DC Power Adaptor x 2
• IR Blaster Cable
• Operation Manual
4. SYSTEM REQUIREMENTS
• Input HDMI and USB source equipment such as DVD, Blu-ray player
and PC/Notebook with connection cables.
• Output display such as HDTV, monitor and active speaker or
amplier with connection cables.
DRAFT
1
5. FEATURES
• HDMI and HDCP v1.1 compliant
• Supports USB 2.0 high-speed devices
• Supports video resolution up to 1920x1080@60Hz & WUXGA
(1920x1200 Reduced Blanking)
• No driver require
• Supports cable distance up to 100 meters over single CAT5e/6
cable
• Supports smart data compression to optimize the bandwidth usage
over network
• Supports matrix application with maximum 16 pairs of TX/RX
installed on a single Ethernet network
• Supports cascading over Giga Ethernet hubs of TCP/IP protocol
• Bidirectional IR
• Additional analog audio extension with MIC function
DRAFT
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front Panel
RS-232 IR OUTPOWERLINK PAIR SEL FUNC
RESET
LINK
1
ON
234
2 3 4 5 6 7
1
1Power LED: The LED will illuminate when the device is connected
with power.
2LINK LED: The LED will illuminate when the Transmitter is linked with
Receiver.
3RS-232: This slot is to connect with D-Sub 9-pin female null modern
cable from PC’s system for controlling both the input source and
output display over RS-232.
4IR OUT: This slot is to connect with IR Blaster cable included in the
package for IR signal sending and controlling the HDMI input
source equipment.
5LINK PAIR SEL: This dip switch allows user with matrix setting for link
up to 16 pairs of the devices with single IP router. Each pair must
have the same dip switch setting in order to pair to the right device
setting. The factory default setting is at 0000.
6RESET: Use nail to push the button inside the box to repower ON the
device.
7FUNC button: Hold this button still and powering ON the devices,
when both link LED and power LED twinkling, press reset button
and release FUNC button. This will reset Transmitter back to factory
default setting.
DRAFT
3
6.2 Transmitter Rear Panel
CAT5e/6/7
HDMI IN LINE IN LINE OUTUSB 5V DC
1 2 3 4 5 6
1CAT5e/6/7: Connect to Receiver device with RJ-45 terminated
cable.
2HDMI IN: This slot is to connect with input source such as DVD or
Blu-ray player with connection cable.
3LINE IN: Connect from audio source equipment with 3.5mm phone
jack cable for audio signal sending to Receiver side.
4LINE OUT: Connect to active speaker or amplier for outputting
MIC input sound from Receiver end.
5USB: Connect with USB host for data sending or USB control to/from
the Receiver connected USB equipment.
65V DC: Connect with 5V power supply to trigger ON the device.
DRAFT
4
6.3 Receiver Front Panel
POWERRS-232IR OUTI
RU
SB
12
34
LINK PAIR SELLINK
1
ON
234
2 3 4 5 6 7
1
1POWER LED: The LED will illuminate when the device is connected
with power.
2LINK LED: The LED will illuminate when the Receiver is linked with
Transmitter.
3RS-232: This slot is to connect with D-Sub 9-pin female null modern
cable from PC’s system for controlling both the input source and
output display over RS-232.
4IR OUT: Connect with IR Blaster included in the package for IR
signal received from Transmitter side to blast out and to control the
desire device.
5IR window: To receive the remote control signal and send to
Transmitter side for IR signal blast out.
6LINK PAIR SEL: This dip switch allows user with matrix setting for link
up to 16 pairs of the devices with single IP router. Each pair must
have the same dip switch setting in order to pair to the right device
setting. The factory default setting is at 0000.
7USB 1~4: Connect USB devices such as keyboard, mouse, thumb
drive, hard disk and …etc. for data sending or control over USB
connected devices.
DRAFT
5
6.4 Receiver Rear Panel
CAT5e/6/7
RESETHDMI OUTMIC IN LINK OUT5V DCVIDEO
MODE
USB
LINK
1 2 3 4 5 6 7 8
1CAT5e/6/7: Connect from transmitter device with RJ-45 terminated
cable.
2VIDEO MODE: Press this button to switch in between the video and
graphic mode. The OSD will display your selection every time when
the button is pressed.
Hold this button still and powering ON the devices, when both link
LED and power LED twinkling, press reset button and release VIDEO
MODE button. This will reset Receiver back to factory default
setting.
3USB LINK: Press this button once or twice to allow the Receiver
to be link up or unlink with the Transmitter and the OSD will show
“starting USB” or “Stopping USB” on the HDMI output display.
Under multiple links of Receivers on a single transmitter, press it for
3 seconds to get the host control of USB on the Receiver. When the
LED illuminate it means the device has obtain the USB authority.
4RESET: Use nail to push the button inside the box to repower ON the
device.
5HDMI OUT: Connect with HD TV or monitor for output image
display.
6MIC IN: Connect with microphone device or audio source
equivalent signal for audio signal output to Transmitter’s Line out.
7LINE OUT: Connect with active speakers or audio equipment for
audio signal display from Transmitter line in.
85V DC: Plug the DC power supply into the unit and connect the
adaptor to AC wall outlet. Power LED will illuminate when the
power is ON.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Receptor de CYP
CYP
CYP CH-2527TXV Manual de usuario
CYP
CYP PU-607BDWP-RX Manual de usuario
CYP
CYP CA-DVIAT Manual de usuario
CYP
CYP CH-514RXWPL Manual de usuario
CYP
CYP HDBaseT 5Play PUV-1510RX Manual de usuario
CYP
CYP AVX-101C-KIT Manual de usuario
CYP
CYP PU-507RX-2H Manual de usuario
CYP
CYP PU-507RX-SCD Manual de usuario
CYP
CYP CH-1604TXD Manual de usuario
CYP
CYP CA-USBAT Manual de usuario
CYP
CYP CH-1529RXV Manual de usuario
CYP
CYP CH-1507TX Manual de usuario
CYP
CYP CH-331H-RX Manual de usuario
CYP
CYP COH-TX1 Manual de usuario
CYP
CYP CA-HDMI150R Manual de usuario
CYP
CYP CA-COMP100R Manual de usuario
CYP
CYP CH-507RXWPL Manual de usuario
CYP
CYP CH-U331RX Manual de usuario
CYP
CYP AVX-101F-KIT Manual de usuario
CYP
CYP CH-515RXPT Manual de usuario
