Creality Ender-5 Plus Manual

V.2.1

◆This guide book is for standard Ender-5 Plus only.

◆Please plug the power cord into a three-hole

power jack.

◆Detailed instructions are available in the TF card.

To be the Chief Evangelist

To make Top-quality 3D printer

Ender-5 Plus Printer

Guide Book

WARNING

1. Do not use the printer any way other than described herein in order to avoid personal injury or property

damage.

2. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a

well-ventilated, low-dust environment.

3. Please place your printer under a stable environment in order to achieve hight print quality.

4. Before using experimental or exotic filaments, we suggest using standard filaments such as ABS or PLA to

calibrate and test the machine.

5. Do not use any other power cable except the one supplied. For your safety, you must use a grounded

three-prong power outlet.

6. Do not touch the nozzle or printing surface during operation as they may be hot. Keep hands away from

machine while in use to avoid burns or other personal injuries.

7. Do not wear gloves or loose clothing when operating the printer. Such cloths may become tangled in the

printers moving parts leading to printer damage, burns, or personal injuries.

8. When cleaning debris from the printer hot end, please use the provided tools. Do not touch the nozzle

when heated. This maybe cause personal injury.

9. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to

remove dust, adhered printing plastics or any other material off the frame, guide rails, or wheels . Use

glass cleaner or isopropyl alcohol to clean the print surface before every print for consistent results.

10. Children under 10 years of age should not use the printer without supervision.

1.Introduction....................................1

2.General List....................................2

3.Assembly Step.......................................3

4.Cable Connection............................7

5.Screen Information........................8

6 . L o a d i n g F i l a m e n t ...........................9

7.Bed Leveling.....................................10

8.Softw are Installation ........ ...............12

9.Preparing to P rint ..........................13

10. C i r c u i t W i r i n g . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Preface

Dear consumers,

Thank you for choosing our products. For your best experience, please read the instructions before operating the

Printer. Our 3D team will always be ready to provide you the best service. Please contact us via the phone number or e-

mail address provided on the last page of the instruction when you encounter any issue with the Printer.

For a better experience in using our product, you may learn how to use the Printer in the following ways:

1. View the accompanied instructions and videos in the TF card.

2. Visit our official website www.creality3d.cn You will find relevant software/hardware information, contact details and

operation and maintenance instructions on the website.

Contents

4 5 6 7

11 12 13

1. BL Touch

2. broken filament detecting device

3. Hot Bed

4. Maincontrol box

5. Power switch

6. Touch screen

7. Leveling nut

8. Hot end

9. X-axis limit switch

10. X-axis motor

11. TF card＆USB

12. Z-axis motor

13. Antivibration feet

14. Filament Holder

15. Y-axis motor

16. Y-axis limit switch

Introduction ：

General List :

Tool List

G:Bottom Frame

F:Z-axis Frame

D:2040 Aluminum

profile(4Pcs)

E:Hot Bed

C:Filament Holder

A:Top Frame

B:Extruder kit No. Image Name Qty

Wrench & Screw

driver

1set

TF Card & Reader

1set

Spatula

Pliers

0.4mm

Nozzle Cleaner

Power Cable

Filament(200)g

Spare Parts

1set

USB

M5X25

8pcs

2040 Aluminum

profile(4Pcs) Bottom Frame

Ready:

Frame Assembly Pt. 1

Step 1. Keep the front of the Bottom Frame facing you.

Step 2. Take one of the Aluminum frame pieces and place it in the corner of the bottom frame , On top of the frame, and lined up

with the corner. Notice the hole at the top of piece facing left and right, in relation to the front of the printer. Use 2 M5x25

screws and washers to secure part to the bottom frame.

Step 3. Install the remaining 2 aluminum profile in the same way as Step 3.

Note: Please note that

the hole at the top of piece

facing left and right, in

relationto the front of the

printer.

Note:

1. Tighten the four screws on

the top, then tight the side screws.

2. Facing your top-side Y-axis

passive block, you can adjust it to

adjust the timing belt tightness.

Front

Frame Assembly Pt. 2

8pcs

M5X25

Ready:

Top Frame

Step 1. Make sure the front of the bottom frame is facing you .

Step 2. 1) Place the Top frame on top of all four aluminum frames.

2) Line up the pre-drilled screw holes on tops of aluminum frame with the holes on top of Top frame and tighten in place with an M5x25

screw and washer at each corner.

3) After 4 screws on top are tightened, use 4 M5x25 screws and washers to fasten corner brackets in each corner of Top frames, into

corresponding holes on outside edge of aluminum frame

Behind

8pcs

M5X30

Lift Z-axis Frame Right Z-axis Frame

Ready:

Frame Assembly Pt. 3

Step 1. Make sure the front of the bottom frame is facing you .

Step 2. Place double Z-axis frame inside of previously assembled frame. The double Z-axis frame is mounted on the left and right 2040 aluminum

profiles of the top frame and must be aligned with the aluminum profile. Making sure the motor is on the bottom, attach the frame to

the lower and upper assembly with a M5x30 screw and washer at each corner. The upper and lower assembly extrusions will have

corresponding pre-drilled holes for these screws.

Step 3. After the installation of the double Z-axis frame is completed, please check if your Y-axis can move smoothly. If the movement is

hindered and the aluminum profile is rubbed, please adjust the eccentric nut and reassemble your Z-axis frame.

Frame Assembly Pt. 4

Hot Bed

Filament Holder

8pcs

M4X10 M5X8 2pcs

M5 T-nut

Step 1. Make sure the front of the base(b) is facing you. Place the hot bed on the support plate of the double Z-axis frame and align with the

profile holes on it.

Step 2. Using 4 M4x10 screws, connect the hot bed to the support plate on the Z-axis frame. Make sure the hot bed is flat and all six

screws are securely fastened.

Step 3. Subsequently, pass the M5x8 socket head cap screw through the threaded hole on the of the metal plate filament bracket , then pass

the M5 T-nut and gently turn the M5 T-nut. Do not tighten. Rotate the M5 T-nut that has been installed on the metal plate filament

bracket into a position parallel to the groove of the aluminum profile, and insert it into the aluminum profile. The M5 T-nut below the

metal plate filament bracket is parallel to the groove of the 2040 aluminum profile and is inserted into it. The upper M5 T-nut on the

metal plate filament bracket is parallel to the 2040 aluminum profile and inlaid, then tighten the screw with an Allen key and tighten

the M5 T-nut to a position perpendicular to the groove of the aluminum profile.

Select the correct input voltage to

match your local mains (230V or 115V).

Bed Cable Connection

Nozzle Cable Connection

Cable Connection ：

BL Touch Connection

Broken filament detecting device Connection

5Pin

3Pin

Otros manuales para Ender-5 Plus

Tabla de contenidos

Otros manuales de Impresora 3D de Creality

Creality

Creality CR-10 S5 Manual de usuario

Creality

Creality CR-30 Manual de usuario

Creality

Creality HALOT-ONE PLUS Manual de usuario

Creality

Creality K1C Manual de usuario

Creality

Creality Ender-5 Plus Manual de usuario

Creality

Creality Ender-3 Instrucciones de montaje

Creality

Creality Sermoon V1 Manual de usuario

Creality

Creality CR-10 S5 Instrucciones de montaje

Creality

Creality Ender-5 Manual

Creality

Creality CR-10 Series Manual

Creality

Creality Sermoon V1 Manual de usuario

Creality

Creality 3dpRINTmILL Manual de usuario

Creality

Creality Ender-3 Manual de usuario

Creality

Creality HALOT-MAX Manual de usuario

Creality

Creality CR-10 Smart Manual de usuario

Creality

Creality 3dpRINTmILL Manual de usuario

Creality

Creality CR-100 Manual

Creality

Creality LD-006 Manual de usuario

Creality

Creality 3dpRINTmILL Manual de usuario

Creality

Creality CR-10 Smart Manual de usuario

Creality

Creality CR-X Pro Manual de usuario

Creality

Creality TL4800 Manual de usuario

Creality

Creality CR-10 Smart Pro Manual de usuario

Creality

Creality HALOT-LITE Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario