Clarke IQ2000 Manual de usuario
MOUNTING & OPERATION
INSTRUCTIONS
GC0715
INFRARED QUARTZ WALL HEATER
MODEL NO: IQ2000
PART NO: 6939004
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
INTRODUCTION
Thank you for purchasing this CLARKE Infrared Wall Heater.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.
If disposing of this product or any damaged components, do not dispose of
with general waste. This product contains valuable raw materials. Metal
products should be taken to your local civic amenity site for recycling of metal
products. Gas filled heater tubes should be disposed of appropriately.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY PRECAUTIONS
GENERAL
1. Always read and ensure you fully understand the following precautions
and the hazards associated with this type of heater. Do not allow anyone
who has not read these instructions to operate this heater. Please keep
these instructions in a safe place for future reference.
2. Always check for damage before using the heater. Any damage should
be properly repaired or the part replaced. If in doubt, DO NOT use the
heater and consult your local Clarke dealer.
3. Never carry out any modifications to this product. If experiencing difficulty
of any kind consult your local dealer.
4. Use the heater in accordance with any applicable fire regulations.
OPERATING ENVIRONMENT
1. Never use the heater where petrol, paint thinners or other highly flammable
vapour or where high levels of airborne dust may be present.
2. Never locate the heater facing combustible materials such as screens,
workshop furniture etc.
3. Disconnect the heater from the power supply when not in use.
4. Never place anything on top of the heater so as to impede free air flow.
5. Do not expose the heater or power cable to rain or wet conditions. Any
water entering the heater will increase the risk of electric shock. If used
outdoors, the heater should be protected from direct rainfall.
6. Never locate the heater near combustible materials such as curtains,
furniture etc. Allow at least 1 metre distance.
7. Allow a distance of at least 1 metre from adjacent wall and avoid installing
the heater close to power socket outlets.
8. Do not allow the heating element to become covered with dust which
could become a fire hazard. If used in a dusty workplace it should be
cleaned as described under Cleaning and Maintenance.
9. Never touch the heater element for at least 15 minutes after switching off.
10. Do not leave the heater unattended.
11. Do not use this heater with a programmable timer used to switch it on
automatically.
12. Never attach any duct work in front of the heater.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PERSONAL SAFETY
1. When the heater is to be operated in the presence of other people the
user is responsible for informing those present of the safety precautions and
of the hazards involved.
2. The heater is not to be used by children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge.
3. Always ensure that people and animals are well away from the front of the
heater when in operation.
4. This heater will be hot when in operation and should not be touched until it
has fully cooled down after switching off.
5. Never leave the heater in use without adult supervision if children or
animals are likely to be present.
6. Do not use this heater in small rooms when occupied by persons unable to
leave the room on their own unless constant supervision is provided.
ELECTRICAL SAFETY
1. Make sure that the voltage on the rating label is the same voltage as the
power supply. If in doubt consult a qualified electrician.
2. Never modify the plug in any way. Do not use adaptor plugs with earthed
appliances. Correct plugs and outlets will reduce the risk of electric shock.
3. Do not abuse the electrical cable. Keep the cable away from sources of
heat, sharp edges or moving parts. Damaged or tangled cables increase
the risk of electric shock.
4. Regularly inspect the power cable for damage. DO NOT use if damaged &
keep it away from the source of heat. If damaged, it must be replaced.
DAMAGE & REPAIRS
1. If necessary, have your heater repaired by a qualified person using
identical replacement parts to maintain the safety of the heater.
SAFETY SYMBOLS
The above symbols are found on the heater.
Hot surface, do not
touch.
Do not cover.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which is
marked Nor coloured Black.
• The wire which is coloured Brown must be connected to the terminal which
is marked Lor coloured Red.
• The wire which is coloured Yellow and Green must be connected to the
terminal which is marked E or or coloured Green.
.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.
WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE
MAINS SUPPLY.
WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT
ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Ensure that the outer sheath of the cable is firmly held by the clamp
Neutral
(Blue)
Live
(Brown)
Earth
(Green and Yellow)
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PREPARATION
UNPACKING
Remove heater from the carton and check for any damage sustained in
transit. Notify your Clarke dealer immediately of any defects.
MOUNTING THE HEATER
The heater is resitant to splashing but should be sheltered from direct rainfall,
as should the power cable, plug and supply outlet socket. If used outdoors, an
awning, overhanging roof or other shelter should be used to protect from rain.
The heater must be mounted on a suitable wall at a height not less than 1.8m
above the floor.
The heater should be positioned with at least 1m clearance at the front
between the heater and any obstruction including walls or other combustible
surfaces. Always position the heater facing the centre of the space to be
heated, not pointing directly at any nearby surfaces. Never place any objects
on, or against the heater.
Any equipment or furniture should be a safe distance away, as they could be
adversely affected by heat. Take care that the heat is not directed at curtains
or other fabrics.
1. Drill four holes in the wall to
accept the plastic wall-plugs
supplied, at the distance apart as
shown. Other wall plugs may be
required, dependant upon the
construction of the wall.
2. Screw the mounting bracket to
the wall.
3. Fit the heater onto the wall
bracket and secure in place with
the screw knob.
4. Set the downwards angle of the
heater by loosening the mounting
bracket with a large x-head
screwdriver and adjusting the
angle before re-tightening.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
OPERATION
1. Connect the mains cable to a suitable power socket.
2. Pull the string repeatedly to cycle
through the following heat
settings;
•O= Off
•I= Low
•II = Medium
•III = High
CLEANING AND MAINTENANCE
PERIODICALLY
1. If there is any build up of dirt, wipe thoroughly with a damp cloth ,taking
care that no moisture enters the heater.
2. Inspect the power cable for damage. Undue heat will cause the cable to
stiffen and crack in which case it should be replaced.
3. Ensure heating elements are free of dust (use compressed air to clean if
possible. (ALWAYS wear a dust mask if performing this task).
4. Refer to your Clarke dealer if the heater element needs replacing.
WARNING: BEFORE CARRYING OUT ANY MAINTENANCE, ENSURE THE
HEATER IS SWITCHED OFF, DISCONNECTED FROM THE MAINS SUPPLY,
AND HAS BEEN GIVEN ADEQUATE TIME TO COOL DOWN.
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
FAULT FINDING
TECHNICAL SPECIFICATION
SYMPTOM PROBLEM SOLUTION
Heater does not
operate, although
plugged in and
switched on.
Plug is loose/ bad con-
nection.
Remove the plug & check
the connection of the plug
and socket.
Fuse blown. Replace if necessary and
investigate the cause. If
fuse blow repeatedly,
consult your Clarke dealer.
No power at socket
outlet
Insert plug into an
operational socket.
Input voltage incorrect. Ensure power supply
matches the rating on the
label.
Dimensions (L x W x H) 178 x 480 x 253 mm
Weight 1.9 kg
Electrical Supply 230 V, 50hz
Power Cable length 1.8 m
Protection Degree IP24 (water splash resistant)
Operating Temperature -20 to 30
Tilt Range Level to -25 degrees
Heat Output 2kW
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PARTS DIAGRAM
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PARTS LIST
ID DESCRIPTION ID DESCRIPTION
1 Front Housing 21 Nut
2 Front Housing Clip 22 Internal Wire Assembly
3 Heating Element 23 PVC Sticker
4 Self-tapping Screw 24 Cable Bush
5 Reflector Bracket 25 Drawing Bush
6 Reflector 26 Display Disc
7 Nut 27 Cable Clamp
8 Cable Clip 28 Plastic Plug
9 Self tapping Screw 29 Switch
10 Spring Washer 30 Self tapping Screw
11 Rear Housing 31 Self tapping Screw
12 Hinge Board 32 Screw Knob
13 U-seal Ring 33 Switch Bracket
14 Hinge Seal 34 Wall Bracket
15 Hinge 35 Star Washer
16 Screw 36 Power Cable
17 Control Box Bottom 37 Self-tapping Screw
18 Closed End Connector 38 Self-tapping Screw
19 Seal 39 Screw
20 Control Box Cover
Tabla de contenidos
Otros manuales de Calentador de Clarke
Clarke
Clarke DEVIL 5000PTC Manual de instrucciones
Clarke
Clarke IQ2000S Manual de lista de piezas
Clarke
Clarke OFR13/250 Manual de instrucciones
Clarke
Clarke XR55 Manual de instalación y operación
Clarke
Clarke OFR 5/50 Manual de instrucciones
Clarke
Clarke DEVIL 4040 Manual de instrucciones
Clarke
Clarke BR13/250 Manual de instrucciones
Clarke
Clarke XR80 Manual de instrucciones
Clarke
Clarke BR9/200 Manual de instrucciones
Clarke
Clarke OFR 9/90 Manual de instrucciones
Clarke
Clarke DEVIL 370SPD Manual de instalación y operación
Clarke
Clarke DEVIL 350B 230V Manual de instalación y operación
Clarke
Clarke DEVIL 7003 Manual de instrucciones
Clarke
Clarke XRV100 Guía de solución de problemas
Clarke
Clarke DEVIL 2000PTC-B Manual de instrucciones
Clarke
Clarke DEVIL 2000PTC Manual de instrucciones
Clarke
Clarke XR60B Manual de instrucciones
Clarke
Clarke OFR 9 Manual de instrucciones
Clarke
Clarke CONTRACTOR GRH30 Manual de instrucciones
Clarke
Clarke DEVIL 2800PTC Manual de instrucciones
