Cisco Aironet 1830 Series Manual de usuario

Manual

Access Point Cisco Aironet 1832i

Baixe aqui o manual, em inglês, do Access Point Cisco Aironet 1832I e

veja todas as funções que este potente ponto de acesso pode oferecer

para a sua empresa.

www.bztech.com.b

GETTING STARTED GUIDE

Cisco Aironet 1830 Series Access Points

1About this Guide

2About the Access Point

3Safety Instructions

4Unpacking the AP

5Ports and Connectors on the AP

6Preparing the AP for Installation

7Installation Overview

8Performing a Pre-Installation Configuration

9Mounting and Grounding the Access Point

10 Powering the Access Point

11 Configuring and Deploying the Access Point

12 Checking the Access Point LEDs

13 Miscellaneous Usage and Configuration Guidelines

14 Related Documentation

15 Declarations of Conformity and Regulatory Information

1 About this Guide

This guide provides instructions on how to install and configure your Cisco Aironet 1830 Series Access

Point. This guide also provides mounting instructions and limited troubleshooting procedures.

The 1830 Series Access Point is referred to as the access point, or abbreviated as AP in this document.

2 About the Access Point

The Cisco Aironet 1830 series access point is an 802.11 a/b/g/n/ac (Wave 2) access point, with internal

antennas only. The access point can be mounted on a wall or a ceiling, and supports 2.4 GHz 3x3

802.11b/g/n MIMO and 5 GHz 3x3 802.11 a/n/ac (Wave 2) MIMO applications simultaneously.

Access Point Model Numbers and Regulatory Domains

The Cisco Aironet 1830 series access point comes in both universal regulatory domain and

non-universal regulatory domain model number formats. See the following table for the model number

formats.

The ‘UX’ in a model number indicates a universal regulatory domain access point. For information on

how to set the regulatory domain and country configurations of a universal regulatory domain access

point, see the Cisco Aironet Universal AP Priming and Cisco AirProvision User Guide, at:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html

The ‘x’ placeholder in the other model numbers represents the regulatory domain. The ‘x’ can be any

one of these supported regulatory domains: A, B, C, D, E, F, H, I, K, N, Q, R, S, T, Z.

For more information on supported regulatory domains, see the following page:

http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd

80537b6a.html

Universal Regulatory Domain

Model Number Format

Non- Universal Regulatory

Domain Model Number Format

Models Numbers AIR-AP1832I-UXK9

AIR-AP1832I-UXK9C

AIR-AP1832I-x-K9

AIR-AP1832I-x-K9C

Model numbers ending in Care, by default, factory-shipped with a Cisco Mobility Express software

image. For more information, see the Cisco Mobility Express User Guide at the following URL:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/1/user_guide/b_ME_User_Guid

e.html

Access Point Features

A full listing of the access point's features and specification are provided in the Cisco Aironet 1830

Series Access Point Data Sheet, at the following URL:

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1830-series-access-points/datashee

t-c78-735582.html

The features of the 1830 series access points at release are:

•Supported mode(s) of operation:

–

Centralized

•Supports Cisco Mobility Express solution. The 1830 series access point can operate as a master

AP (having an integrated wireless controller functionality) in a Cisco Mobility Express network.

For more information, see the Cisco Mobility Express User Guide at the following URL:

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/1/user_guide/b_ME_User_

Guide.html

•Radio features supported are:

–

2.4 GHz and 5 GHz concurrent radios

–

2 GHz radio with 3TX x 3RX and two spatial streams SU-MIMO

–

5 GHz radio with 3TX x 3RX 802.11ac Wave 2 capable with two spatial streams SU-MIMO

and MU-MIMO

–

802.11ac based Transmit Beamforming

–

Quality of Service (QoS)

–

Radio Resource Management (RRM)

–

Rogue Detection

–

BandSelect

•The AP supports the following hardware external interfaces:

–

RS-232 Console Interface through RJ-45

–

Local Power DC Jack

–

Mode button. For information on how to use the Mode button, see “Using the Mode Button”

section on page 23.

–

USB 2.0 port (No software support at this time)

–

One multi-color LED status indicator. See the “Checking the Access Point LEDs” section on

page 21 for information on the colors of the LED status indicator.

–

1 x 10/100/1000 Mbps WAN Ethernet Port (RJ-45), with PoE support.

•1832I model access point has three integrated 2.4 GHz and 5 GHz dual-band antennas. Peak

antenna gain is approximately 3 dBi and 5 dBi in 2.4 GHz and 5 GHz bands respectively.

3 Safety Instructions

Translated versions of the following safety warnings are provided in the translated safety warnings

document that is shipped with your access point. The translated warnings are also in the Translated

Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury.

Before you work on any equipment, be aware of the hazards involved with electrical

circuitry and be familiar with standard practices for preventing accidents. Use the

statement number provided at the end of each warning to locate its translation in the

translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning

Read the installation instructions before you connect the system to its power source.

Statement 1004

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

Warning

This product relies on the building’s installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than:

20A.

Statement 1005

Warning

Do not operate your wireless network device near unshielded blasting caps or in an

explosive environment unless the device has been modified to be especially qualified for

such use.

Statement 245B

Caution The fasteners you use to mount an access point on a ceiling must be capable of

maintaining a minimum pullout force of 20 lbs (9 kg) and must use a minimum of 4 holes

on the mounting bracket, or a minimum of 2 holes when mounting on a network box.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by Environment A of the

IEEE 802.3af/at Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the

Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power

injector in air handling spaces.

Note Use only with listed Information Technology Equipment (ITE) equipment. For more

information on ITE equipment, refer to article 645 of the latest National Electrical Code

(NEC).

4 Unpacking the AP

To unpack the access point, follow these steps:

Step 1 Unpack and remove the access point and the mounting accessories, from the shipping box.

Step 2 Return any packing material to the shipping container and save it for future use.

Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact

your Cisco representative or reseller for instructions.

–

The access point

–

Mounting bracket (AIR-AP-BRACKET-1= or AIR-AP-BRACKET-2=, only if selected when

you ordered the access point)

–

T-RAIL clips and Channel Adapter (only if selected when you ordered the access point)

5 Ports and Connectors on the AP

The 1830 series access points have an LED indicator on the face of the unit, above the Cisco logo, as

shown in Figure 1. For information on the LED scheme, see the “Access Point Status LEDs” section

on page 21.

The ports and connections on the access point are shown in Figure 2.

Figure 1 Access Point LED Indicator Position

1LED indicator position. For information on the LED scheme, see the “Access Point Status LEDs”

section on page 21.

354089

Figure 2 Access Point Ports and Connections

1Security hasp for padlocking AP to mounting

bracket 4USB 2.0 port

(No software support at this time)

2Mode button

For information on how to use the Mode

button, see “Using the Mode Button” section

on page 23.

5PoE-In port (Ethernet Uplink port)

3RJ-45 console port 648 V DC input power port

354181

1 2 3 4 5 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco AIR-AP1020 - 1000 Series Lightweight Access... Manual de usuario

Cisco

Cisco Aironet 1530 Manual de usuario

Cisco

Cisco WAP131 Manual de instrucciones

Cisco

Cisco Small Business WAP551 Manual de instrucciones

Cisco

Cisco Aironet 3800P Series Manual de usuario

Cisco

Cisco Aironet 1520 Series Manual

Cisco

Cisco Aironet 1040 Series Manual de usuario

Cisco

Cisco AIR-CAP3502I-A-K9 Manual de usuario

Cisco

Cisco ASR 1001 Manual

Cisco

Cisco AT&T U-VERSE VEN401 Manual de usuario

Cisco

Cisco Meraki MR52 Manual de usuario

Cisco

Cisco Linksys WAP610N Manual de usuario

Cisco

Cisco MERAKI MR72 Manual

Cisco

Cisco Catalyst Wireless 9164I Series Manual de usuario

Cisco

Cisco Catalyst 9136I Series Manual

Cisco

Cisco Aironet 1600 Series Guía de referencia rápida

Cisco

Cisco GR10-HW-EU Manual de usuario

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de usuario

Cisco

Cisco AIR-BR1310G-A-K9-R - Aironet 1310 Outdoor Access... Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Cisco

Cisco AIR-AP1121G-E-K9 Manual

Cisco

Cisco aironet 2800 series Guía de referencia rápida

Cisco

Cisco Aironet 1300 Series Manual de usuario

Cisco

Cisco AIR-CAP1552H-x-K9 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario