Cisco MERAKI MR72 Manual

Meraki MR72

Hardware Installation Guide

Trademarks

Cisco, Cisco Meraki, Meraki, Meraki MR72, and Meraki Cloud

Controller are trademarks of Cisco Systems, Inc. Other brand and

product names are registered trademarks or trademarks of their

respective holders.

Warranty

Cisco Systems, Inc. provides a one year warranty on this product.

Warranty details may be found at www.meraki.cisco.com/support.

Table of Contents

.1 Scope of Document and Related Publications

.2 MR72 Overview

.3 Pre-Install Preparation

.4 Installation Instructions

.5 Troubleshooting

.6 Regulatory

1 Scope of Document and Related Publications

The MR72 Hardware Installation Guide describes the installation

procedure for the MR72 access point.

Additional reference documents are available online at

meraki.cisco.com/support

2 MR72 Overview

The Meraki MR72 is an enterprise-class, 802.11abgn/ac outdoor

access point designed for rugged environments. When connected to

the Meraki Cloud Controller, the MR72 enables the creation of high-

speed and reliable networks that cover large outdoor and industrial

areas quickly, easily, and cost-effectively.

The Meraki MR72 has an operating temperature of -40oto 60oC.

2.1 Package Contents

The MR72 package contains the following:

- MR72 access point

- Wall screws & anchors

- Mounting plate

- Cable gland

- Mounting straps

2.2 Antennas and Ports

The Meraki MR72 has two radios. Each radio has two external antenna

connectors; both connectors for a particular radio should be attached

to the same type of antenna. The 5 GHz radio is used for mesh or client

communication. The 2.4 GHz radio is primarily used for client

communication. However, it can also communicate with Meraki 2.4

GHz access points.

Meraki offers a number of different antennas for use with the MR72:

MA-ANT-20, MA-ANT-21, MA-ANT-23, and MA-ANT-25.

The Meraki MA-ANT-20 omni-directional antennas must be installed

vertically.

The Meraki MA-ANT-25 patch antenna must be installed facing

downward, at least 30 degrees from the horizon line.

2.3 Power Source Options

The MR72 access point can be powered using either an 802.3at

capable PoE switch or the Meraki 802.3at PoE injector (sold

separately).

2.4 LED Indicators and Run Dark Mode

Your MR72 uses a single LED to inform the user of the device’s status.

Function

LED Status

Meaning

Power Up/

Boot

Solid

Orange

Power is applied

Connecting

Rainbow

Device in process of connecting to

the Meraki Dashboard

Connected

Solid White

Fully operational

Upgrading

Flashing

White

During boot or no WAN link

The MR72 may be operated in “Run Dark” mode for additional security

and to reduce the visibility of the access point. In this mode, the LED

will not be illuminated. This mode may be enabled through Meraki

Dashboard.

3 Pre-Install Preparation

You should complete the following steps before going on-site to

perform an installation.

3.1 Configure Your Network in Dashboard

Meraki recommends that you add your MR72 to a network in

Dashboard before mounting it in the field. The following is a brief

overview only of the steps required to add an MR72 to your network.

For detailed instructions about creating, configuring and managing

Meraki wireless networks, refer to the Meraki Cloud Controller Manual

(cisco.meraki.com/support/#documentation).

1. Login to http://dashboard.meraki.com. If this is your first time,

create a new account.

2. Find the network to which you plan to add your nodes or create a

new network.

3. Add your nodes to your network. You will need your Meraki order

number (found on your invoice if you ordered directly from

Meraki) or the serial number of each node, which looks like

Qxxx-xxxx-xxxx, and is found on the bottom of the unit.

4. Finally, go to the map / floor plan view and place each node on

the map by clicking and dragging it to the location where you

plan to mount it. You can always modify the location later.

3.2 Check and Upgrade Firmware

To ensure your MR72 performs optimally immediately following

installation, Meraki recommends that you facilitate a firmware upgrade

prior to mounting your MR72.

1. Attach your MR72 to power and a wired Internet connection.

2. The MR72 will turn on and the LED will glow solid orange. If the

unit does not require a firmware upgrade, the LED will turn solid

white within 30 seconds.

* If the unit requires an upgrade, the LED will cycle rainbow until the

upgrade is complete, at which point the Power LED will turn solid

white. You should allow about an hour for the firmware upgrade to

complete, depending on the speed of your internet connection.

3.3 Check and Configure Firewall Settings

If your network will be located behind a firewall, it must allow outgoing

connections on particular ports to particular IP addresses in order for

the MR72 to be able to seamlessly communicate with the Cloud

Controller. The most current list of outbound ports and IP addresses

can be found here:

http://bit.ly/oZpMQ7

3.4 Assigning IP Addresses to MR72s

All gateway MR72s (MR72s with Ethernet connections to the LAN)

must be assigned routable IP addresses. These IP addresses can be

dynamically assigned via DHCP or statically assigned.

3.4.1 Dynamic Assignment

When using DHCP, the DHCP server should be configured to assign a

static IP address for each MAC address belonging to a Meraki AP.

Other features of the wireless network, such as 802.1X authentication,

may rely on theproperty that the APs have static IP addresses.

3.4.2 Static Assignment

Static IPs are assigned using the local web server on each AP. The

following procedure describes how to set the static IP:

1. Using a client machine (e.g., a laptop), connect to the AP either

wirelessly (by associating to any SSID broadcast by the AP) or

over a wired connection. If using a wired connection, connect

the client machine to the MR72 either through a PoE switch or a

Meraki PoE Injector. If using a PoE switch, plug an Ethernet cable

into the MR72’s Ethernet jack, and the other end into a PoE

switch. Then connect the client machine over Ethernet cable to

the PoE switch. If using a Meraki PoE Injector, connect the MR72

to the “PoE” port of the Injector, and the client machine to the

“LAN” port.

2. Using a web browser on the client machine, access the AP’s

built-in web server by browsing to http://ap.meraki.com.

Alternatively, browse to http://10.128.128.128.

3. Click on the “Static IP Configuration” tab. Log in. The default

user name is “admin”. The default password is the AP’s serial

number, with hyphens included (e.g., Q2BD-551C-ZYW3).

4. Configure the static IP address, net mask, gateway IP address

and DNS servers that this AP will use on its wired connection.

5. If necessary, reconnect the AP to the LAN.

3.5 Collect Tools

You will need the following tools to perform an installation:

- Flat-head screwdriver

- Drill with appropriate bits for mounting wall anchors (if mounting to a

wall)

- Phillips screwdriver

- Tin snips (if mounting with hose clamps)

- Power screwdriver with 5/16” (8 mm) nut driver, Phillips & flat heads

(recommended)

3.6 Collect Additional Hardware for Installation

- Network cables with RJ45 connectors long enough for your particular

mounting location

- 802.3at PoE power source (either PoE switch or Meraki 802.3at PoE

Injector)

- Connection to the internet (if you are setting up your MR72 as a

gateway to the internet)

- Appropriately sized metal straps (if mounting to a pole larger than

3.9” in diameter)

- Specialized mounting hardware if mounting to surface other than

wood, stucco or stone

- Laptop with wireless to verify setup (recommended)

4 Installation Instructions

4.1 Choose Your Mounting Location

A good mounting location is important to getting the best performance

out of your MR72 access point. Keep the following in mind:

1. The device should have unobstructed line of sight to most

coverage areas. For example, if installing in an office filled with

workspaces divided by mid-height cubicle walls, installing on the

ceiling or high on a wall would be ideal.

2. Power over Ethernet supports a maximum cable length of 300 ft

(100 m).

3. If being used in a mesh deployment, the MR72 should have line

of sight to at least two other Meraki devices. For more detailed

instructions regarding access point location selection, reference

the Meraki Network Design Guide

(cisco.meraki.com/support/#documentation).

4. The antennas should be as unobstructed as possible. Make sure

that there is clearance around the MR72 for installation of all of

your chosen antennas.

4.2 Install the MR72

For most mounting scenarios, the MR72 mount plate provides a quick,

simple, and flexible means of mounting your device. The installation

should be done in two steps. First, install the mount plate to your

selected location. Then attach the MR72 to the mount plate.

4.2.1 Remove the Mount Plate from the Access Point

Before installing the mount plate, you must remove it from the back of

the access point.

1. Unscrew the mount plate attachment screw.

2. Lift the mount plate release tab upwards.

3. While holding the mount plate release tab up, slide the mount plate

off the access point.

4.2.2 Attach the Mount Plate

The MR72 mount plate can be used to install your access point in a

wide range of scenarios.

4.2.2.1 Wall or Solid Ceiling Mount Using Mount Plate

Using included wall anchors and screws, attach the mount plate to

your mounting wall or ceiling.

It is recommended that the MR72 be mounted to a wall or solid ceiling

using the mount plate for physical security reasons.

4.2.2.2 Pole Mount Using Mount Plate

Use the included mounting straps to mount the AP to a pole less than

3.9” in diameter. Thread the mounting straps through the mounting

strap slots to secure the mount plate in a horizontal or vertical

Otros manuales para MERAKI MR72

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco AIR-AP1542I-*-K Manual de usuario

Cisco

Cisco Aironet 340 Series Manual

Cisco

Cisco ASR 1001 Manual

Cisco

Cisco Aironet 2802E Manual de usuario

Cisco

Cisco AT&T U-VERSE VEN401 Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Cisco

Cisco M10-RM Guía de inicio rápido

Cisco

Cisco Meraki CW9163E Manual de usuario

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Catalyst IW9165E Manual de usuario

Cisco

Cisco Meraki MR76 Manual de usuario

Cisco

Cisco WAP371 Manual de usuario

Cisco

Cisco WAP121 Manual de usuario

Cisco

Cisco Aironet 1260 Series Manual de usuario

Cisco

Cisco Meraki MR84 Manual

Cisco

Cisco ASA 5506-X Manual de usuario

Cisco

Cisco Small Business AP541N Manual de usuario

Cisco

Cisco Linksys WAP55AG Manual de usuario

Cisco

Cisco DPH650 Manual de usuario

Cisco

Cisco Aironet 1815T Manual de usuario

Cisco

Cisco Catalyst IW9167E Manual

Cisco

Cisco aironet 1810 series Manual de usuario

Cisco

Cisco Aironet 1240AG Series Manual

Cisco

Cisco CW91641-A Manual

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario