Cisco Aironet 1300 Series Manual de usuario

Quick Start Guide Cisco Aironet 1300 Series Access Point

Read This First

This guide is designed to help you quickly set up and configure your Cisco

Aironet 1300 Series Outdoor Access Point/Bridge.

This guide does not cover mounting the access point/bridge or establishing a

bridge link. Those subjects are covered in the Cisco Aironet 1300 Series

Outdoor Access Point/Bridge Mounting Instructions, which shipped with

your access point/bridge. You must complete the procedures in the mounting

instruction document and then use this guide to initially configure the access

point/bridge to connect to your LAN.

Important Information

Recent Cisco IOS releases have changed the way an unconfigured access

point/bridge behaves when booted for the first time. This section describes

this behavior and provides instructions on how to open‘ the access point’s

configuration pages.

78-15954-02

Cisco IOS Release 12.2(15)JA and Earlier

Setting Default Remarks

SSID autoinstall —

Radio status Enabled —

Roll in Radio

Network

Root bridge —

IP Address Assigned by DHCP If DHCP disabled, the default

IP address is 10.0.0.1. See the

“Assigning Basic Settings”

section on page 18 for

additional information.

Quick Start Guide Cisco Aironet 1300 Series Access Point

Cisco IOS Release 12.3(2)JA

Setting Default Remarks

SSID autoinstall Case-sensitive

Radio status Enabled —

Role in Radio

Network

Root bridge —

IP Address Assigned by DHCP If DHCP disabled, the access

point continues to send DHCP

requests indefinitely. To assign

an IP address, you must access

the unit’s console port. See the

“Using the CLI” section on

page 14 for additional

information.

78-15954-02

Cisco IOS Release 12.3(4)JA and Later

Setting Default Remarks

SSID None assigned You must create an SSID. See

the “Assigning an IP Address

Using the CLI” section on page

Radio status disabled You must enable the radio

interfaces. “Enabling the Radio

Interfaces” section on page 5

for additional information.

Role in Radio

Network

Root AP —

IP Address Assigned by DHCP If DHCP is disabled, the access

point continues to send DHCP

requests indefinitely. To assign

an IP address, you must access

the unit’s console port. See the

“Using the CLI” section on

page 14 for additional

information.

Quick Start Guide Cisco Aironet 1300 Series Access Point

Enabling the Radio Interfaces

In Cisco IOS Release 12.3(4)JA and later, the access point/bridge radio is

disabled by default, and there is no SSID. You must create an SSID and

enable the radios before the access point/bridge will allow wireless

associations from other devices. These changes to the default configuration

improve the security of newly installed access point/bridges.

To enable the radio interfaces using the access point/bridge’s graphical user

interface (GUI), follow these instructions:

1. Use your internet browser to access your access point. The default login

and password is Cisco. Both are case-sensitive.

2. When the Summary Status page displays, choose Express > SSID

Manager. The Global SSID Manager page appears.

3. Create an SSID for each radio interface. An SSID can be any

alphanumeric, case-sensitive entry from 2 to 32 characters. The

following six characters are not allowed: ?, “, $. [. \, and +. In addition,

the following three characters cannot be the first character: !, #, and ;.

4. Click Apply.

5. Choose Network Interface > Radio 802.11g and the Radio Status page

appears.

6. Click Settings and the Radio Settings Page appears.

7. Click Enable in the Enable Radio field.

78-15954-02

8. Click Apply.

9. Close your internet browser.

Note You can enable the radios using the access point’s command

line interface (CLI). See the Cisco IOS Software Configuration

Guide for Cisco Aironet Access Points for additional

information.

Checking the LEDs

The access point/bridge has four LEDs on its back panel that provide

operational information about the access point/bridge. See the following

illustration.

Quick Start Guide Cisco Aironet 1300 Series Access Point

The following table shows normal mode LED indications.

RRadio LED SStatus LED

EEthernet LED IInstall LED

117061

78-15954-02

Note For detailed information about the LEDs, see the Cisco Aironet 1300

Series Outdoor Access Point/Bridge Hardware Installation Guide.

Ethernet

LED

Status

LED

Radio

LED

Meaning

Off — — Ethernet link is down or disabled.

Blinking

green

— — Transmitting and receiving Ethernet

packets.

Blinking

amber

— — Transmitting and receiving Ethernet

errors.

Amber — — Firmware error.

— Blinking

green

— Root bridge mode—no remote

bridges associated.

Non-root bridge—not associated to

the root bridge.

— Green — Root mode—associated to at least

one remote bridge.

Non-root mode—associated to the

root bridge.

Quick Start Guide Cisco Aironet 1300 Series Access Point

Note The access point/bridge uses a blinking code to identify various

error conditions. See the Cisco Aironet 1300 Outdoor Access Point/

Bridge Hardware Installation Guide for a detailed description of the

codes.

Blinking

amber

— General warning.

Red Amber Red Loading Firmware error.

— — Blinking

green

Transmitting and receiving radio

packets—normal operation.

— — Blinking

amber

Maximum retries or buffer full

occurred on radio interface.

Amber Radio firmware error.

Ethernet

LED

Status

LED

Radio

LED

Meaning

78-15954-02

Related Documents

The following document provides detailed information about installing your

access point/bridge:

•Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware

Installation Guide

This guide provides instructions for configuring your access point/bridge

using its graphical user interface (GUI). You may also configure the access

point/bridge through its console port to access the command line interface

(CLI) and issue IOS commands. If you choose to use the CLI, please refer to

the following documents for additional information and instructions:

•Cisco Aironet 1300 Series Outdoor Access Point/Bridge Software

Configuration Guide

•Cisco IOS Command Reference for Cisco Aironet Access Points and

Bridges

In addition to the integrated antenna, the access point/bridge can be used with

existing certified Cisco Aironet 2.4-GHz antennas. If you are using an

optional external antenna, please refer to the applicable documentation for

the specific antenna. Antenna documentation is shipped with the antenna.

With the exception of this guide, the documents identified in this section are

available on Cisco.com. Follow this link to access them:

http://www.cisco.com/en/US/products/ps5861/tsd_products_support_series_

home.html

Otros manuales para Aironet 1300 Series

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Catalyst 9120AX Series Manual de usuario

Cisco

Cisco Aironet 1200 Series Manual

Cisco

Cisco AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access... Manual

Cisco

Cisco Meraki MR52 Manual de usuario

Cisco

Cisco FM1000 Gateway Manual

Cisco

Cisco Small Business WAP44 Manual de instrucciones

Cisco

Cisco Meraki MR36H Manual de usuario

Cisco

Cisco Aironet 1260 Series Manual de usuario

Cisco

Cisco Catalyst IW9167E Manual

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de usuario

Cisco

Cisco Meraki Go GR62 Manual de usuario

Cisco

Cisco AIR-AP1230B-A-K9 - Syst. 1230 Aironet WLAN... Manual

Cisco

Cisco 1004-CH - 1004 Enet/ISDN/Bri Rter Guía de referencia rápida

Cisco

Cisco Meraki MR46E Manual de usuario

Cisco

Cisco Aironet 1600 Series Guía de referencia rápida

Cisco

Cisco Aironet 1140 Series Manual de usuario

Cisco

Cisco 1142 - Aironet Standalone AP Manual de usuario

Cisco

Cisco Aironet 340 Series Manual

Cisco

Cisco Aironet 1550 Series Manual de usuario

Cisco

Cisco 1262 Manual de usuario

Cisco

Cisco Aironet 350 Series Manual

Cisco

Cisco aironet 1524SB Instrucciones de instalación y funcionamiento

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual de usuario

Cisco

Cisco Linksys WAP610N Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario