Cisco Small Business WAP551 Manual de instrucciones

Cisco Small Business

WAP551 Wireless-N Access Point with PoE

and

WAP561 Wireless-N Selectable-Band Access Point

with PoE

ADMINISTRATION

GUIDE

Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE 1

Contents

Chapter 1: Getting Started 5

Starting the Web-Based Configuration Utility 5

Using the Access Point Setup Wizard 6

Getting Started 9

Window Navigation 10

Chapter 2: Status and Statistics 12

System Summary 12

Network Interfaces 14

Traffic Statistics 15

WorkGroup Bridge Transmit/Receive 16

Associated Clients 16

TSPEC Client Associations 18

TSPEC Status and Statistics 20

TSPEC AP Statistics 22

Radio Statistics 22

Email Alert Status 24

Log 24

Chapter 3: Administration 25

System Settings 26

User Accounts 26

Time Settings 28

Log Settings 30

Email Alert 32

HTTP/HTTPS Service 35

Management Access Control 37

Manage Firmware 38

Download/Backup Configuration File 40

Configuration Files Properties 42

Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE 2

Contents

Copy/Save Configuration 42

Reboot 43

Discovery—Bonjour 44

Packet Capture 44

Support Information 51

Chapter 4: LAN 52

Port Settings 52

VLAN and IPv4 Address Settings 53

IPv6 Addresses 54

IPv6 Tunnel 56

Chapter 5: Wireless 58

Radio 58

Rogue AP Detection 66

Networks 69

Scheduler 81

Scheduler Association 83

Bandwidth Utilization 83

MAC Filtering 84

WDS Bridge 85

WorkGroup Bridge 89

Quality of Service 92

WPS Setup 95

WPS Process 102

Chapter 6: System Security 105

RADIUS Server 105

802.1X Supplicant 107

Password Complexity 109

Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE 3

Contents

WPA-PSK Complexity 110

Chapter 7: Client Quality of Service 111

Client QoS Global Settings 111

ACL 111

Class Map 118

Policy Map 123

Client QoS Association 125

Client QoS Status 127

Chapter 8: Simple Network Management Protocol 129

General SNMP Settings 129

Groups 133

Users 135

Targets 136

Chapter 9: Captive Portal 138

Captive Portal Global Configuration 139

Instance Configuration 140

Instance Association 143

Web Portal Customization 143

Local Groups 147

Local Users 148

Authenticated Clients 149

Failed Authentication Clients 150

Chapter 10: Single Point Setup 152

Single Point Setup Overview 152

Access Points 157

Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE 4

Contents

Sessions 160

Channel Management 161

Wireless Neighborhood 165

Chapter A: Deauthentication Message Reason Codes 168

Deauthentication Reason Code Table 168

Appendix B: Where to Go From Here 170

Cisco Small Business WAP551 and WAP561 Wireless-N Access Point 5

Getting Started

This chapter provides an introduction to the Wireless Access Point (WAP) devices

web-based configuration utility, and includes these topics:

•Starting the Web-Based Configuration Utility

•Using the Access Point Setup Wizard

•Getting Started

•Window Navigation

Starting the Web-Based Configuration Utility

This section describes system requirements and how to navigate the web-based

configuration utility.

Supported Browsers

•Internet Explorer 7.0 or later

•Chrome 5.0 or later

•Firefox 3.0 or later

•Safari 3.0 or later

Browser Restrictions

•If you are using Internet Explorer 6, you cannot directly use an IPv6 address

to access the WAP device. You can, however, use the Domain Name System

(DNS) server to create a domain name that contains the IPv6 address, and

then use that domain name in the address bar in place of the IPv6 address.

•When using Internet Explorer 8, you can configure security settings from

Internet Explorer. Select Tools > Internet Options and then select the

Security tab. Select Local Intranet and select Sites. Select Advanced and

then select Add. Add the intranet address of the WAP device (http://<ip-

Getting Started

Using the Access Point Setup Wizard

Cisco Small Business WAP551 and WAP561 Wireless-N Access Point 6

address>) to the local intranet zone. The IP address can also be specified

as the subnet IP address, so that all addresses in the subnet are added to

the local intranet zone.

•If you have multiple IPv6 interfaces on your management station, use the

IPv6 global address instead of the IPv6 local address to access the WAP

device from your browser.

By default, the web-based AP configuration utility logs out after 10 minutes of

inactivity. See HTTP/HTTPS Service for instructions on changing the default

timeout period.

To log out, click Logout in the top right corner of the web-based AP configuration

utility.

Using the Access Point Setup Wizard

The first time that you log into the WAP device (or after it has been reset to the

factory default settings), the Access Point Setup Wizard appears to help you

perform initial configurations. Follow these steps to complete the wizard:

NOTE If you click Cancel to bypass the Wizard, the Change Password page appears. You

can then change the default password for logging in. For all other settings, the

factory default configurations apply.

You must log in again after changing your password.

STEP 1 Click Next on the Welcome page of the Wizard. The Configure Device - IP

Address window appears.

STEP 2 Click Dynamic IP Address (DHCP) if you want the WAP device to receive an IP

address from a DHCP server. Or select Static IP Address to configure IP Address

manually. For a description of these fields, see VLAN and IPv4 Address Settings.

STEP 3 Click Next. The Single Point Setup — Set a Cluster window appears. For a

description of Single Point Setup, see Single Point Setup.

STEP 4 To create a new Single Point Setup of WAP devices, select Create a New Cluster

and specify a New Cluster Name. When you configure your devices with the

same cluster name and enable Single Point Setup mode on other WAP devices,

they automatically join the group.

Getting Started

Using the Access Point Setup Wizard

Cisco Small Business WAP551 and WAP561 Wireless-N Access Point 7

If you already have a cluster on your network, you can add this device to it by

clicking Join an Existing Cluster, and then entering the Existing Cluster Name.

If you do not want this device to participate in a Single Point Setup at this time,

click Do not Enable Single Point Setup.

(Optional) You can enter text in the AP Location field to note the physical location

of the WAP device.

STEP 5 Click Next. The Configure Device - Set System Date and Time window appears.

STEP 6 Select your time zone, and then set the system time manually or set up the WAP

device to get its time from an NTP server. For a description of these options, see

Time Settings.

STEP 7 Click Next. The Enable Security - Set Password window appears.

STEP 8 Enter a New Password and enter it again in the Confirm Password text box. For

more information about passwords, see User Accounts.

NOTE You can uncheck the Password Complexity box if you wish to disable

the password security rules. However, we strongly recommend keeping the

password security rules enabled.

STEP 9 Click Next. The Enable Security - Name Your Wireless Network window appears

for the Radio 1 interface.

NOTE For this window and the following two windows (Wireless Security

and VLAN ID), you configure these settings for the Radio 1 interface first.

Then, for WAP561 devices, the windows repeat to enable you to configure

these settings for Radio 2.

STEP 10 Enter a Network Name. This name serves as the SSID for the default wireless

network.

STEP 11 Click Next. The Enable Security - Secure Your Wireless Network window appears.

STEP 12 Choose a security encryption type and enter a security key. For a description of

these options, see System Security.

STEP 13 Click Next. The Wizard displays the Enable Security- Assign the VLAN ID For Your

Wireless Network window.

STEP 14 Enter a VLAN ID for traffic received on the wireless network.

It is suggested that you assign a different VLAN ID from the default (1) to wireless

traffic, in order to segregate it from management traffic on VLAN 1.

STEP 15 Click Next.

Getting Started

Using the Access Point Setup Wizard

Cisco Small Business WAP551 and WAP561 Wireless-N Access Point 8

STEP 16 For the WAP561 device, the Network Name, Wireless Security, and VLAN ID

pages show to enable configuring Radio 2. When finished with configuring Radio

2, click Next.

The Wizard displays the Enable Captive Portal - Create Your Guest Network

window.

STEP 17 Select whether or not to set up an authentication method for guests on your

network, and click Next.

If you click No, skip to STEP 25.

If you click Yes, the Wizard displays the Enable Captive Portal - Name Your Guest

Network window.

STEP 18 Specify a Guest Network Name for Radio 1. For the WAP561 device, select

whether the guest network uses Radio 1 or Radio 2.

STEP 19 Click Next. The Wizard displays the Enable Captive Portal - Secure Your Guest

Network window.

STEP 20 Choose a security encryption type for the guest network and enter a security key.

For a description of these options, see System Security.

STEP 21 Click Next. The Wizard displays the Enable Captive Portal - Assign the VLAN ID

window.

STEP 22 Specify a VLAN ID for the guest network. The guest network VLAN ID should be

different from the management VLAN ID.

STEP 23 Click Next. The Wizard displays the Enable Captive Portal - Enable Redirect URL

window.

STEP 24 Select Enable Redirect URL and specify a fully qualified domain name or IP

address in the Redirect URL field (including http://). If specified, guest network

users are redirected to the specified URL after authenticating.

STEP 25 Click Next. The Wizard displays the Summary - Confirm Your Settings window.

STEP 26 Review the settings that you configured. Click Back to reconfigure one or more

settings. If you click Cancel, all settings are returned to the previous or default

values.

STEP 27 If they are correct, click Submit. Your WAP setup settings are saved and a

confirmation window appears.

STEP 28 Click Finish. The Getting Started window appears.

Getting Started

Cisco Small Business WAP551 and WAP561 Wireless-N Access Point 9

Getting Started

To simplify device configuration through quick navigation, the Getting Started

page provides links for performing common tasks. The Getting Started page is the

default window every time you log into the web-based AP configuration utility.

Links on the Getting Started Page

Category Link Name (on the Page) Linked Page

Initial Setup Run Setup Wizard Using the Access

Point Setup Wizard

Configure Radio Settings Radio

Configure Wireless Network Settings Networks

Configure LAN Settings LAN

Run WPS WPS Setup

Configure Single Point Setup Single Point Setup

Device

Status

System Summary System Summary

Wireless Status Network Interfaces

Quick

Access

Change Account Password User Accounts

Upgrade Device Firmware Manage Firmware

Backup/Restore Configuration Download/Backup

Configuration File

Otros manuales para Small Business WAP551

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco 500 Series Manual del operador

Cisco

Cisco USC 3330 Manual de usuario

Cisco

Cisco Catalyst 9164 Series Manual de usuario

Cisco

Cisco Meraki MR20-HW Manual de usuario

Cisco

Cisco Catalyst IW9165D Manual

Cisco

Cisco aironet 1524SB Instrucciones de instalación y funcionamiento

Cisco

Cisco Linksys WAP610N Manual de usuario

Cisco

Cisco Catalyst 9136I Series Manual

Cisco

Cisco Linksys WAP54GX Instrucciones de funcionamiento originales

Cisco

Cisco Catalyst Wireless 9162I Series Manual

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de instrucciones

Cisco

Cisco Aironet 1140 Series Manual de usuario

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Manual de usuario

Cisco

Cisco WAP371 Manual de instrucciones

Cisco

Cisco Aironet 1520 Series Manual

Cisco

Cisco Catalyst 9130AX Series Manual de usuario

Cisco

Cisco Aironet LAP1522 Manual

Cisco

Cisco Aironet 1400 Series Manual de usuario

Cisco

Cisco Meraki MR70 Manual de usuario

Cisco

Cisco AP541N-A-K9 Manual de instrucciones

Cisco

Cisco Small Business AP541N Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de usuario

Cisco

Cisco WAP125 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario