Cisco Aironet 1140 Series Manual de usuario

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 1/30
Updated: February 11, 2010
Getting Started Guide: Cisco Aironet 1140 Series Autonomous
Access Point
Table Of Contents
Cisco Aironet 1140 Series Autonomous Access Point
About this Guide
Safety Instructions
Overview
Verifying Shipped Components
Key Ports and Components
Performing a Site Survey
Obtaining and Assigning an IP Address
Connecting to the Access Point Locally
Assigning the IP Address to the BVI
Assigning an IP Address Using the CLI
Mounting the Access Point
Conguring Basic Settings
Default Settings on the Express Setup Page
Enabling the Radio Interfaces
Conguring Security Settings
Conguring Basic Security Settings
Understanding Express Security Settings
Using VLANs
Express Security Types
Conguring Security for 802.11n
Express Security Limitations
Using the Express Security Page
Troubleshooting
Checking the Access Point LED
Conguring System Power Settings
Finding More Troubleshooting Help
Access Point Specications
Obtaining Documentation and Submitting a Service Request
Declarations of Conformity and Regulatory Information
Manufacturers Federal Communication Commission Declaration of Conformity Statement
VCCI Statement for Japan
Guidelines for Operating Cisco Aironet Access Points in Japan
Japanese Translation

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 2/30
English Translation
Statement 371—Power Cable and AC Adapter
English Translation
Industry Canada
Canadian Compliance Statement
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
Declaration of Conformity for RF Exposure
United States
Canada
European Union
Australia
Administrative Rules for Cisco Aironet Access Points in Taiwan
Chinese Translation
English Translation
Chinese Translation
Operation of Cisco Aironet Access Points in Brazil
Access Point Models
Regulatory Information
Portuguese Translation
English Translation
Getting Started Guide
Cisco Aironet 1140 Series Autonomous Access Point
78-18997-01
1 About this Guide
This Guide explains how to install and congure your Cisco Aironet 1140 Series Autonomous
Access Point. This guide also provides mounting instructions and limited troubleshooting
procedures.
2 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings
document that is shipped with your access point. The translated warnings are also in the Translated
Safety Warnings for Cisco Aironet Access Points, which is available on your documentation CD and
cisco.com.
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 3/30

Use the statement number provided at the end of each warning to locate its

translation in the translated safety warnings that accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Warning Read the installation instructions before you connect the system to its

power source. Statement 1004

Warning This product must be connected to a Power-over-Ethernet (PoE) IEEE

802.3af compliant power source or an IEC60950 compliant limited power source.

Statement 353

Warning This equipment must be externally grounded using a customer-supplied

ground wire before power is applied. Contact the appropriate electrical inspection

authority or an electrician if you are uncertain that suitable grounding is available.

Statement 366

Warning Installation of the equipment must comply with local and national

electrical codes. Statement 1074

Warning This product relies on the building's installation for short-circuit

(overcurrent) protection. Ensure that the protective device is rated not greater than:

20A. Statement 1005

Warning Do not operate your wireless network device near unshielded blasting caps

or in an explosive environment unless the device has been modied to be especially

qualied for such use. Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas

should be located at a minimum of 7.9 inches (20 cm) or more from the body of all

persons.

Statement 332

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 4/30

Caution When mounting the access point to a wall or ceiling, be sure to use appropriate fasteners.

The fasteners used must be capable of maintaining a minimum pullout force of 20 lbs (9

kg) and must use all 4 indented holes on the low-prole mounting bracket.

Caution This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as dened by Environment A of the

IEEE 802.af Standard.

Note The access point is suitable for use in environmental air space in accordance with section

300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of

the Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or

power injector in air handling spaces.

Note Use only with listed ITE equipment.

3 Overview

This section explains necessary tasks prior to installing the 1140 series access point.

Verifying Shipped Components

To unpack and verify the contents of the 1140 series access point and accessory kit, follow these

steps:

Step1 Unpack and remove the access point and the accessory kit from the shipping box.

Step2 Return any packing material to the shipping container and save it for future use.

Step3 Verify that you have received the items shown in Figure1. If any item is missing or

damaged, contact your Cisco representative or reseller for instructions.

Figure1 Shipping Box Contents

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 5/30

Standard ceiling adjustable T-rail clip

1140 series access point

Mounting bracket

6-32 x 1/4 in. (0.63 cm) at head screws

Key Ports and Components

Familiarize yourself with the access point before continuing with the installation. Figure2 shows the

access point key components.

Figure2 Access Point Ports and Connections

Kensington lock

slot

Console port

Power connection

Security padlock and hasp

Ethernet port

Low-prole mounting bracket pins (feet for desk or table-top

mount)

Performing a Site Survey

Before you mount and deploy your access point, we recommend that you perform a site survey (or

use a site planning tool) to determine the best location to install your access point.

You should have the following information about your wireless network available:

• Access point locations.

• Access point mounting options: below a suspended ceiling, on a at horizontal surface, or on a

desktop.

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 6/30

Note You can mount the access point above a suspended ceiling but you must purchase

additional mounting hardware: See the "Mounting the Access Point" section for additional

information.

• Access point power options: power supplied by a DC power supply, PoE from a network device,

or a PoE power injector/hub (usually located in a wiring closet).

Note Access points mounted in a building's environmental airspace must be powered using PoE

to comply with safety regulations.

Cisco recommends that you make a site map showing access point locations so that you can

record the device MAC addresses from each location and return them to the person who is

planning or managing your wireless network.

4 Obtaining and Assigning an IP Address

To browse to the access point Express Setup page, you must either obtain or assign the access

point IP address using one of these methods:

Note The access point does not have a default IP address.

• Assign a static IP address by connecting to its console port and accessing the access point CLI.

• Use a DHCP server (if available) to automatically assign an IP address. You can nd out the

DHCP-assigned IP address by using one of the following methods:

– Connect to the access point console port and use a Cisco IOS command to display the IP

address, such as show interface bvi1.

– Provide your organization's network administrator with your access point MAC address. Your

network administrator will query the DHCP server using the MAC address to identify the IP

address. The MAC address is on a label attached to the bottom of the access point.

– Use the CLI and serial port to identify the assigned IP address.

Connecting to the Access Point Locally

If you need to congure the access point locally (without connecting it to a wired LAN), you can

connect a PC to its console port by using a DB-9 to RJ-45 serial cable.

Caution Be careful when handling the access point, the bottom plate might be hot.

Follow these steps to open the CLI by connecting to the access point console port:

Step1 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the

access point and to the COM port on a computer.

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 7/30

Note The Cisco part number for the serial cable is AIR-CONCAB1200.

Step2 Set up a terminal emulator on your PC to communicate with the access point. Use the

following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop

bit, and no ow control.

Assigning the IP Address to the BVI

When you assign an IP address to the access point by using the CLI, you must assign the address

to the bridge-group virtual interface (BVI). Beginning in a privileged EXEC mode, follow these steps

to assign an IP address to the access point BVI using the access point console port.



Command

Purpose

Step1

congure terminal

Enter global conguration mode.

Step2

interface bvi1

Enters interface conguration mode for the BVI.

Step3

ip address ip_address

net_mask

Assigns an IP address and subnet mask address to

the BVI.

Assigning an IP Address Using the CLI

Follow these steps to access the CLI using a Telnet session. These steps are for a PC running

Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for

detailed instructions.

Step1 Select Start > Programs > Accessories > Telnet.

If Telnet is not listed in your Accessories menu, select Start > Run, type Telnet in the entry

eld, and press Enter.

Step2 When the Telnet window appears, click Connect and select Remote System.

Step3 In the Host Name eld, type the access point IP address and click Connect.

Note If you are connected to the access point using a Telnet session, you lose your connection to

the access point when you assign a new IP address to the BVI. If you need to continue

conguring the access point using Telnet, use the new IP address to open another Telnet

session to the access point.

5 Mounting the Access Point

Cisco Aironet 3500, 1260, 1140, 1130, and 1040 series access points can be mounted in several

congurations, including on a suspended ceiling, on a hard ceiling or wall, on an elecrtical or

network box, and above a suspended ceiling. Click this URL to browse to complete access point

mounting instructions:

http://www.cisco.com/en/US/docs/wireless/access_point/mounting/guide/apmount.html

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 8/30

Note The integrated antenna design of the 1140 series access point is designed for horizontal

surfaces, (table top and ceiling installations). When mounted to such surfaces, the

integrated antennas produce the best antenna radiation pattern. For advanced features

such as voice, location, and rogue access point detection, ceiling mounting is strongly

recommended. However, for smaller areas such as conference rooms, kiosks,

transportation, and hot-spot usage where the customer is concerned primarily with data

coverage and not advanced features, you can mount the unit on a wall using wall anchors.

Caution Do not use plastic wall anchors or the keyhole slots on the mounting bracket for ceiling

installations. When mounting the access point on a hard ceiling, use four fasteners

capable of maintaining a minimum pullout force of 20 lbs (9 kg).

6 Conguring Basic Settings

Before you can congure basic settings, the access point and your PC needs an IP address. See

the "Obtaining and Assigning an IP Address" section.

Follow these steps to congure basic settings for the access point using the GUI Express Setup

page.

Step1 Open your browser, and enter the access point IP address in the address eld. A username

and password screen appears.

Step2 Enter the username Cisco and password Cisco. The username and password are case

sensitive.

Step3 Press Enter. The Summary Status page appears.

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 9/30

Step4 If required, congure the power settings as described in the previous section. Otherwise,

Click Express Setup. The Express Setup page appears.

22/09/2019 Getting Started Guide: Cisco Aironet 1140 Series Autonomous Access Point - Cisco

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html 10/30

Step5 Congure the settings using the following sections as a guide.

• Host Name—The host name (or system name) is a name for the access point that identies it on

your network. The system name appears in the titles of the management system pages.

• Conguration Server Protocol—This setting species how the access point obtains an IP

address.

DHCP—IP address is automatically assigned by the network DHCP server.

Static IP—The access point uses a static IP address that you enter in the IP address

eld.

• IP Address—This setting assigns or changes the access point IP address. If DHCP is enabled,

the access point obtains its IP address from your network DHCP server. You can assign a static IP

address in this eld.

• IP Subnet Mask—The IP subnet mask identies the subnet on which the access point resides.

This subnet is provided by your network administrator. If DHCP is enabled, leave this eld blank.

• Default Gateway—The default gateway identies the address the access point uses to access

another network. This gateway is provided by your network administrator. If DHCP is enabled, leave

this eld blank.

• Web Server—This setting species the type of HTTP used to access the access point using a

web browser.

Standard (HTTP)—Standard protocol used to transfer HTML using unencrypted

trac between web browsers.

Secure (HTTPS)—Protocol used to transfer secure data by using encrypted trac to

and from the user by means of a Secure Socket Layer (SSL).

Otros manuales para Aironet 1140 Series

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Aironet 1815w Manual de usuario

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Meraki MR70 Manual de usuario

Cisco

Cisco Meraki MR52 Manual

Cisco

Cisco Catalyst Wireless 9163E Manual de usuario

Cisco

Cisco Aironet AIR-AP1200 Manual

Cisco

Cisco Catalyst IW9165D Manual

Cisco

Cisco Aironet 1300 Series Manual de usuario

Cisco

Cisco Aironet 1530 Series Manual

Cisco

Cisco Small Business AP541N Manual de usuario

Cisco

Cisco Meraki MR55-HW Manual

Cisco

Cisco Meraki MR45 Manual de usuario

Cisco

Cisco WAP361 Manual de usuario

Cisco

Cisco Catalyst Wireless 9166D1 Manual

Cisco

Cisco 700 series Manual de usuario

Cisco

Cisco Aironet 1540 Series Manual

Cisco

Cisco MR74 Manual

Cisco

Cisco Meraki GR10 Manual de usuario

Cisco

Cisco Wap581 Manual de usuario

Cisco

Cisco Meraki Guía

Cisco

Cisco Meraki MR12 Manual de usuario

Cisco

Cisco Aironet 1830 Series Manual de usuario

Cisco

Cisco ISR Manual de usuario

Cisco

Cisco CW91641-A Manual

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario