CAS PD-II Manual de usuario

Otros manuales para PD-II

5

Tabla de contenidos

Otros manuales de Escala de CAS

CAS

CAS CL series Manual de usuario

CAS

CAS K5 Manual de usuario

CAS

CAS PR-II Series Manual de usuario

CAS

CAS BI Series Manual de usuario

CAS

CAS PR-T Series Manual de usuario

CAS

CAS DB-1H Manual de usuario

CAS

CAS K6 Manual de usuario

CAS

CAS CL7200 series Manual de usuario

CAS

CAS LP-II Instrucciones de instalación y mantenimiento

CAS

CAS AD-1 Manual de usuario

CAS

CAS DL Series Manual de usuario

CAS

CAS CL7200 series Manual del propietario

CAS

CAS DL-60 Manual de usuario

CAS

CAS RETAIL WEIGHING SOLUTION CT100 Manual de usuario

CAS

CAS SW-1S Series Manual de usuario

CAS

CAS PB Series Manual de usuario

CAS

CAS LP-1000N Series Manual de usuario

CAS

CAS CL5000J Series Manual de usuario

CAS

CAS HS-1 Manual de usuario

CAS

CAS CL7200 series Manual de usuario

CAS

CAS RW Series Manual de usuario

CAS

CAS MWP Manual de usuario

CAS

CAS WEIGHING SOLUTION SWII PLUS Series Manual de usuario

CAS

CAS ERII-6 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

09/10/09CAS (USA) Corporation 99 Murray Hill Parkway East Rutherford, NJ 07073 PD-II

PROGRAMMING LBS/OZ FOR PD-II CAL MODE OPTIONS

1. Make sure that the scale is off. Remove the platter. Remove the calibration bolts and plate

located on the top front of the scale.

2. After removing the calibration bolts and plate you will see a white micro switch at the bottom of

the hole. Press and hold down the micro switch and turn on the scale.

3. The display will read “CAL” → “Ver XXX “→ “C-0 “. Release the micro-switch. Press the [ # ]

key until the display shows “C-4 “. Replace the platter. ( “ # “ is to increase and “lb/oz“is to

decrease the value )

4. Press the [ ZERO ] key and display should read “C41 XX “. Press [ ZERO ] to go to the next

step “ C42 XX “ → “ C43 XX “ → “C44 XX “ → “ C45 XX “ → “ C46 XX “.

5. Depending on the capacity and function, enter the value “XX “step by step. Press “# “to move

the digit and “* or lb/oz “to change the value. ( see chart below)

6. Note: For the setting “C42” for all capacities single range is “38” and dual range is what is in the

chart below.

7. The settings for the capacity and single/dual range must follow what is on the serial number plate

or else the scale will not be NTEP or legal for trade subject to a fine by Weights and Measures.

15lb/300oz

30lb/600oz

60lb/1000oz

150lb/2000oz

C41

C8

C8

C8

C8

C42

1A

3A

4A

62

C43

00

00

00

00

C44

80

80

80

80

C45

00

00

00

00

C46

00

00

00

00

8. Press the [ ZERO ] key. Display shows “C4 End “then “C-4 “.

9. Press “* or lb/oz “until the display shows “C-0 “.

C41

C44

What the scale does

C8

80

Starts up in lb and can be switched to oz

d0

80

Starts up in oz and can be switched to lb

C8

00

Starts up in lb and will not switch to oz

D0

00

Starts up in oz and will not switch to lb

10. Press the [ ZERO ] key and scale will do its count up test cycle and the go to “0 “which is

back to normal mode

* Make sure to calibrate the scale in lbs or kg before using.

CHANGING TYPE SETTINGS

1. Make sure that power is OFF. While pressing “# “key, then turn on the power. Display will show

“EcrSEt “. Then current ECR type is shown on the display as “tYPE-2 “.

2. If you select ERC type 5, press the “# “key until the display shows it.

3. To save the current type, press the ZERO Key. Display will go back to “0 “.