C.A. Technologies Lynx L200C Manual de usuario

CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS Press /

Siphon

*SUGGESTED

GUN INLET

PRESS.

FAN

CONTROL SCFM AIR CAP

RING

AVAI LABLE FLUI D

NOZZLES

NEEDLES /

marking on needle

22-2030 siphon 50 12

22-2058 p & s 40 6 32-0611 1.1mm (.042") 40-1211 (211)

22-2080 siphon 60 14 32-0614 1.4mm (.055") 40-1214 (214)

22-2062** pressure 80 19 32-0618 1.8mm (.070") 40-1218 (218)

22-2064** pressure 80 22 32-0618V 1.8mm (.070") 40-5301

22-2704 pressure 70 21 32-0818 1.8mm (.070")

22-2765 pressure 80 22 32-0622 2.2mm (.086")

22-2777 pressure 70 23 32-0622V 2.2mm (.086") 40-5301

22-2797 pressure 70 21 32-0628 2.8mm (.110") 40-1228 (228)

22-2880 siphon 60 15 included 32-0628V 2.8mm (.110") 40-5301

22-2900 siphon 45 12 22-1001

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Gun inlet pressures may vary as required by application

**Air caps available with teflon coating (22-2062T & 22-2064T)

40-1222 (222)

L200C 60-1500

included

22-1001

Lynx 200Cynx 200C

ynx 200Cynx 200C

ynx 200C

PRESSURE/SIPHON FEED SPRAY GUN

PRODUCT INFORMATION

DISTRIBUTED BY COATING EQUIPMENT TECHNOLOGY, INC

PHONE: 586-210-0555

WEB: www.cetinc.com

Operation and Maintenance Instructions for

L200CL200C

L200C

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control

fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Remove air cap and clean separately using clean solvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

For siphon setups, first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Have repair kit # 10-106 available before gun disassembly.

Gun head disassembly

To remove the nozzle carrier (5) and air cap adapter (6):

1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (13).

2. Remove the needle seal cartridge (23).

3. Loosen the locknut (9) and remove fluid inlet (10) using a 5/8” open-end wrench.

4. The nozzle carrier (5) and air cap adapter (6) will now slide forward from the gun body (11).

Gun head reassembly

1. Install a new o-ring (7) on the air cap adapter (6).

2. Install o-ring (4) between fluid nozzle body (3) and fluid nozzle carrier (5).

3. Install the thread locknut (9) onto the fluid inlet (10) as far as possible.

4. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (5) inlet port.

5. Slide the nozzle carrier (5) into air cap adapter (6) and insert into the gun body (11) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten.

6. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (10) and tighten firmly.

7. Tighten the needle seal (23) to approx. 12 ft.-lb. torque.

8. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque.

9. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION

1 See Air Cap Chart Air Cap** 16 60-204 Needle Return Spring*

2 See Air Cap Chart Fluid Nozzle Tip** 17 60-201 Rear Bushing

3 32-2201 Fluid Nozzle Body 18 60-119 Seal*

4 98-8020 Gasket* 19 60-1520 Air Valve Assembly

5 60-L21C Nozzle Carrier 20 60-302 Air Valve Poppet

6 60-22 Air Cap Adapter 21 60-125 O-Ring*

7 60-131 O-Ring* 22 61-1003 Air Valve Spring*

8 60-124 Fluid Inlet Seal 23 60-1400 Needle Seal Cartridge*

9 60-128 Locknut 24 60-2101 Trigger

10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control

11 60-1124 Lynx Gun Body Conventional 25A 60-122 Plug (optional)

12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting

13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set

14 60-202 Fluid Control Knob 28 98-0109 Allen Plug

15 60-205 Spring Seat*

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-106

Revised 3/18/14

L200C CONVENT IONAL SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AI R C AP

MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.8mm x 2765

1.8mm x 2797

2.2 mm x 2880

2.2 mm x 2064

1.1, 1.4 mm x 2058

1.1, 1.4 mm x 2030

1.1, 1.4 mm x 2900

P/S

1.4, 1.8 mm x 2080

1.4, 1.8 mm x 2704

1.4, 1.8 mm x 2765

1.4, 1.8 mm x 2777

1.4, 1.8 mm x 2797

1.4, 1.8 mm x 2900

FLUID NOZZLE / AIR CAP SELECTION CHARTS

LYNX Series 200C - Pressure / Siphon Feed Guns

1.1 mm x 2058

1.1 mm x 2030

P/S

Otros manuales de Pistola pulverizadora de pintura de C.A. Technologies

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100 Series Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300H Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200C Manual de usuario

C.A. Technologies

C.A. Technologies LYNX L100CM Manual

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Manual de usuario

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies Tomahawk TG Manual de usuario

C.A. Technologies

C.A. Technologies TOMCAT 100C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Panther 200Z Manual de usuario

C.A. Technologies

C.A. Technologies Techline JR Manual de usuario

C.A. Technologies

C.A. Technologies CPR-FE Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 300H Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100H Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manual de usuario

C.A. Technologies

C.A. Technologies H2O-CPR Manual de usuario

C.A. Technologies

C.A. Technologies CAT-Xpress Guía de solución de problemas

C.A. Technologies

C.A. Technologies FE-Line LCFM Guía de solución de problemas

C.A. Technologies

C.A. Technologies Panther 200H Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 100C Manual de usuario

C.A. Technologies

C.A. Technologies CAT SLP Series Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100CM Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar SLP Manual de usuario

C.A. Technologies

C.A. Technologies JAGUAR SLP Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario