C.A. Technologies Lynx 300H Manual de usuario

HVLP AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS Press /

Siphon

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

AIR CAP

RING

AVAI LABLE F LUI D

NOZZLES TIPS

NEEDLES /

marking on needle

23-1008 pressure 40** 13.5 33-0208 0.8mm (.022") 40-1308 (308)

23-1010 pressure 40** 13.5 33-0210 1.0mm (.040") 40-1310 (310)

23-1012 pressure 40** 13.5 33-0212 1.2mm (.046") 40-1312 (312)

23-1013 pressure 40** 13.5 33-0213 1.3mm (.052") 40-1313 (313)

23-1014 pressure 40** 13.5 33-0214 1.4mm (.055") 40-1314 (314)

23-1015 pressure 40** 13.5 33-0215 1.5mm (.059") 40-1315 (315)

23-1017 pressure 40** 13.5 33-0217 1.7mm (.070") 40-1317 (317)

23-1019 pressure 40** 13.5 33-0219 1.9mm (.075") 40-1319 (319)

23-1022 pressure 40** 13.5 33-0222 2.2mm (.086") 40-1322 (322)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Note: Air cap test gages are available to confirm HVLP compliance.

*Gun inlet pressures may vary as required by application

**When using optional gun regulator, inlet pressure changes to 45psi

IncludedL300H 60-1502 (#2)

Lynx 300Hynx 300H

ynx 300Hynx 300H

ynx 300H

PRESSURE FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Operation and Maintenance Instructions for

L300HL300H

L300H

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply to the gun fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control

fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Remove air cap and clean separately using clean solvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Have repair kit # 10-106 available before gun disassembly.

Gun head disassembly

To remove the nozzle carrier (4) and air cap adapter (6):

1. Remove the air cap (1), fluid nozzle tip (2), fluid nozzle body (3), and needle (13).

2. Remove the needle seal cartridge (23).

3. Loosen the locknut (9) and remove fluid inlet (10) using a 5/8” open-end wrench.

4. The nozzle carrier (4) and air cap adapter (6) will now slide forward from the gun body (11).

Gun head reassembly

1. Install a new o-ring (5 and 7) on the air cap adapter (6).

2. Install the thread locknut (9) onto the fluid inlet (10) as far as possible.

3. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (4) inlet port.

4. Slide the nozzle carrier (4) into air cap adapter (6) and insert into the gun body (11) as far as possible. Be sure the

nozzle carrier (4) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten.

5. Rotate the nozzle carrier (4) until the fluid inlet port in the nozzle carrier (4) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (10) and tighten firmly.

6. Tighten the needle seal (23) to approx. 12 ft.-lb. torque.

7. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque.

8. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

23-1015-G

23-1022-G

23-1017-G

23-1019-G

HVLP AIR CAP TEST GAGES

23-1008-G

23-1010-G

23-1012-G

FOR

L300H

GUNS

23-1013-G

23-1014-G

ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION

1 See Air Cap Chart Air Cap** 16 60-204 Needle Return Spring*

2 See Air Cap Chart Fluid Nozzle Tip** 17 60-201 Rear Bushing

3 33-1201 Fluid Nozzle Body 18 60-119 Seal*

4 60-L31H Nozzle Carrier 19 60-1520 Air Valve Assembly

5 98-8026 O-Ring* 20 60-302 Air Valve Poppet

6 60-34H Air Cap Adapter 21 60-125 O-Ring*

7 60-131 O-Ring* 22 61-1003 Air Valve Spring*

8 60-124 Fluid Inlet Seal* 23 60-1400 Needle Seal Cartridge*

9 60-128 Locknut 24 60-2101 Trigger

10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control

11 60-1114 Lynx Gun Body HVLP 25A 60-122 Plug (optional)

12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting

13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set

14 60-202 Fluid Control Knob 28 98-0109 Allen Plug

15 60-205 Spring Seat*

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-106

L300H HVLP SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AI R C AP

MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.3 mm x 1013

1.5 mm x 1015

1.7 mm x 1017

1.5 mm x 1015

1.7 mm x 1017

1.9 mm x 1019

2.2 mm x 1022

FLUID NOZZLE / AIR CAP SELECTION CHARTS

LYNX Series 300H - Pressure Feed Guns

1.0 mm x 1010 12 P

1.0 mm x 1010

1.3 mm x 1013

Revised 3/18/14

Este manual sirve para los siguientes modelos

Otros manuales de Pistola pulverizadora de pintura de C.A. Technologies

C.A. Technologies

C.A. Technologies LYNX L100CM Manual

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300H Manual de usuario

C.A. Technologies

C.A. Technologies Lynx L200C Manual de usuario

C.A. Technologies

C.A. Technologies H2O-CPR Manual de usuario

C.A. Technologies

C.A. Technologies Tomahawk TG Manual de usuario

C.A. Technologies

C.A. Technologies JAGUAR SLP Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 300C Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100CM Manual de usuario

C.A. Technologies

C.A. Technologies TOMCAT 100C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Lynx L100C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Manual de usuario

C.A. Technologies

C.A. Technologies FE-Line LCFM Guía de solución de problemas

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies CAT SLP Series Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 300C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Jaguar SLP Manual de usuario

C.A. Technologies

C.A. Technologies Techline JR Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100H Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100C 1590 Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario