C.A. Technologies Lynx 100H Manual de usuario

HVLP AIR CAP AND FLUID NOZZLE CHART

MODEL

NO. AIR CAPS

PRESS.

SIPHON

*MAX GUN

INLET PRESS.

FOR HVLP

FAN

CONTROL

SCFM @

MAX GUN

INLET

AI R CAP

RING

STANDARD

IN CAT

PACK

AVAILABLE FLUID

NOZZLES TIPS

NEEDLES /

marking on needle

21-1090 pressure 15 6 31-0205 0.5mm (.020")

21-1091 pressure 15 8 Included 31-0208 0.8mm (.022")

21-1092 pressure 15 8 31-0210 1.0mm (.040")

21-1093 pressure 18 10 31-0212 1.2mm (.046")

21-1094 pressure 33 13 Included 31-0213 1.3mm (.052")

21-1095 pressure 50 22.5 31-0214 1.4mm (.055")

21-1097 pressure 50 22.5 31-0215 1.5mm (.059")

21-1195 pressure 50 22.5 31-0216 1.6mm (.063")

21-1197 pressure 50 22.5 Included 31-0217 1.7mm (.070")

31-0412 1.2Fmm (.046") 40-1112F (112F)

31-0414 1.4Fmm (.055") 40-1114F (114F)

31-0417 1.7Fmm (.070") 40-1117F (117F)

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Note: Air cap test gages are available to confirm HVLP compliance.

*Gun inlet pressures may vary as required by application

40-1100 (100)

LYNX 100H

(L100H)

21-1001

Included

60-1502 (#2)

Lynx 100H

PRESSURE FEED SPRAYGUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Operation and Maintenance Instructions for

L100H

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply to the gun fluid inlet.

3.Fluidflowcan becontrolledusingthefluidcontrolknob,thisrestrictsflowbylimitingneedletravel.Itisbesttocontrol

fluid flow byproper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenanceis essential toinsure propergun operation.

Severalstatesprohibitsprayingsolventintotheatmosphereand require theuse of covered guncleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Removeair cap andclean separatelyusingcleansolvent.

For pressure setups, connect a pressurized solvent supplyto the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Gun head disassembly and reassembly instructions:

Haverepairkit#10-106availablebeforegundisassembly.

Gun head disassembly

Toremove thenozzle carrier (5) and aircap adapter (6):

1. Remove the air cap (1-2), fluid nozzle tip (3), fluid nozzle body(4), and needle (13).

2.Remove the needlesealcartridge (23).

3. Loosen thelocknut (9) andremove fluid inlet(10) using a5/8” open-end wrench.

4. The nozzle carrier (5) and air cap adapter (6) will now slide forward from the gun body (11).

Gun head reassembly

1. Install a new o-ring (7) on the air cap adapter (6).

2. Install the thread locknut (9) onto the fluid inlet (10) as far as possible.

3. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (5) inlet port.

4. Slide the nozzle carrier (5) into air cap adapter (6) and insert into the gun body(11) as far as possible. Be sure the

nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten.

5. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the

body. While in this position, insert the fluid inlet (10) and tighten firmly.

6. Tighten the needle seal (23) to approx. 12 ft.-lb. torque.

7. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque.

8. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION

1See Air Cap Chart Air Cap Retaining Ring** 16 60-204 Needle Return Spring*

2See Air Cap Chart Air Cap** 17 60-201 Rear Bushing

3See Air Cap Chart Fluid Nozzle Tip** 18 60-119 Seal*

431-1201 Fluid Nozzle Body 19 60-1520 Air Valve Assembly

560-L11H Nozzle Carrier 20 60-302 Air Valve Poppet

660-12H Air Cap Adapter 21 60-125 O-Ring*

7 60-131 O-Ring* 22 61-1003 Air Valve Spring*

8 60-124 Fluid Inlet Seal 23 60-1400 Needle Seal Cartridge*

9 60-128 Locknut 24 60-2101 Trigger

10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control

11 60-1114 Lynx Gun Body HVLP 25A 60-122 Plug (optional)

12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting

13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set

14 60-202 Fluid Control Knob 28 98-0109 Allen Plug

15 60-205 Spring Seat*

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-106

HVLP AIR CAP TEST GAGES

21-1090-G

21-1092-G

21-1093-G

FOR

L100H

GUNS 21-1095-G

21-1097-G

21-1195-G

21-1197-G

***

L100H HVLP SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AIR CAP MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.3, 1.4, 1.5 mm x 1093

1.3, 1.4, 1.5 mm x 1095

1.3, 1.4, 1.5 mm x 1097

1.6, 1.7 mm x 1095

1.6, 1.7 mm x 1097

1.6, 1.7 mm x 1195

1.6, 1.7 mm x 1197

FLUID NOZZLE / AIR CAP SELECTION CHARTS

LYNX Series 100H - Pressure Feed Guns

0.5, 0.8 mm x 1090

0.5, 0.8 mm x 1092 10

11 P

1.0, 1.2 mm x 1092

1.0, 1.2 mm x 1093 11

Revised12/29/15

CP-L100H-303R2 CP-L100H-PPSR2

CP-L100H

CP-L100H Smart Pack Includes:

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-L100H-303R2 Includes:

51-303 1 QT Aluminum Pressure Cup

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

CP-L100H-PPSR2 Includes:

91-460 950 mL 3M™ PPS™ Pressure Cup

91-462 Lids and Liners (Available in 25 Pack)

91-475 #18 PPS Adapter

52-5R2 Pressure Cup Regulator

98-0104 3/8” Socket

98-0112 Ratchet Wrench

60-8001 Gun Wrench

98-0113 Gun Cleaning Brush

Air Caps and Needles Shown on Page 1

Este manual sirve para los siguientes modelos

Otros manuales de Pistola pulverizadora de pintura de C.A. Technologies

C.A. Technologies

C.A. Technologies Cougar Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manual de usuario

C.A. Technologies

C.A. Technologies Tomcat Series Manual de usuario

C.A. Technologies

C.A. Technologies Techline JR Manual de usuario

C.A. Technologies

C.A. Technologies CPR-FE Manual de usuario

C.A. Technologies

C.A. Technologies JAGUAR SLP Manual de usuario

C.A. Technologies

C.A. Technologies FE-Line LCFM Guía de solución de problemas

C.A. Technologies

C.A. Technologies Jaguar 300H Manual de usuario

C.A. Technologies

C.A. Technologies FE-Line Fine Finish Manual de usuario

C.A. Technologies

C.A. Technologies H2O-CPR Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100 Series Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 300H Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 100 Series Manual de usuario

C.A. Technologies

C.A. Technologies Tomahawk TG Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200H Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar SLP Manual de usuario

C.A. Technologies

C.A. Technologies TOMCAT 100C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Lynx 100CVT Manual de usuario

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 100C Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario