C.A. Technologies Tomahawk TG Manual de usuario

CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART

MODEL

NO.

PRESS /

SIPHON AIR CAP FLUID TIP

RANGE

FAN

CONTROL SCFM AIR CAP

RING

AVAILABLE FLUID

NOZZLES

NEEDLES /

marking on needle

21-2166 0.6 - 1.8 5

21-2266 0.6 - 1.8 12 31-0606 0.6mm (.022")

21-2266T 0.6 - 1.8 12 31-0607 0.7mm (.028")

21-2366 0.6 - 1.8 12 31-0610 1.0mm (.040")

21-2466 0.6 - 1.8 15 31-0612 1.2mm (.046")

21-2163 0.6 - 1.8 8 31-0613 1.3mm (.052")

21-2263 0.6 - 1.8 14 31-0615 1.5mm (.059")

21-2266-3 0.6 - 1.8 16.2 31-0618 1.8mm (.070")

21-2266-3T 0.6 - 1.8 16.2

Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)

*Gun inlet pressures may vary as required by application

TG 60-1317 Included

Siphon

Pressure

40-2807 (2807)

40-2810 (2810)

40-2815 (2815)

Tomahaomaha

omahaomaha

omahawkwk

wkwk

PRESSURE/SIPHON FEED SPRAY GUN

PRODUCT INFORMATION

Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708

www.spraycat.com

Operation and Maintenance Instructions for

omahaomaha

omahawkwk

wkwk

Spray Guns

Operation

1. Connect air supply hose at handle of gun.

2. Connect a pressurized fluid supply to the gun fluid inlet.

3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control

fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.

4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.

Maintenance

IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.

Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.

1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures

instructions.

2. If a gun cleaner is not being used:

Remove air cap and clean separately using clean solvent.

For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow

thru the gun until clean.

NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.

Not recommended to soak entire spray gun in solvent.

Gun head disassembly and reassembly instructions:

Have repair kit # 10-140 available before gun disassembly.

Disassembly

1. Remove the trigger by removing both screws (19).

2. Remove fluid control knob (11).

3. Remove needle return spring (13) and needle (12).

4. Remove air valve assembly (9) using a 9/16” wrench.

5. Using a 7/16” wrench remove the needle seal cartridge (20).

6. Using a 13 mm wrench remove the side port control (10) and air control (15).

7. Using a 11/16” wrench loosen locknut (18), using a 5/8” wrench remove fluid inlet (17).

8. Remove air cap (1), remove fluid tip (2) using a 3/8” socket.

9. Using a 1” wrench remove head insert (3).

Reassembly

1. Install a new o-ring (7 and 8) on air valve assembly, lightly lubricate o-rings with vasoline and reinstall air valve (9) into

the gun body (6).

2. Install a new seal (5) in gun body (6). Reinstall head insert into gun body and tighten. Reinstall fluid tip (2) and tighten.

3. Install new seal (5) in gun body. Reinstall and tighten fluid inlet (17). Tighten locknut (18) after fluid inlet has been

tightened.

4. Remove the shipping pin from a new needle seal cartridge (20). Install new needle seal cartridge (20).

5. Reinstall side port control (10) and air control (15).

6. Reinstall needle (12), needle return spring (13) and fluid control knob (11).

7. Reinstall air cap (1).

ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION

1 See A ir Cap Char t A ir Cap** 12 See A ir Cap Char t Fluid Needle**

2 See Air Cap Chart Fluid Nozzle Tip** 13 60-211 Needle Return Spring*

3 60-15C Head Insert 14 60-104 Air Inlet Fitting

5 60-137 O-Ring* 15 60-1319 Air Control

6 60-1301-GL Gun Handle 16 60-2111 Trigger

7 98-5125 O-Ring* 17 60-126 Fluid Inlet

8 98-5225 O-Ring* 18 60-128 Locknut

9 60-1320 Air Valve Assembly 19 60-1315 Trigger Pivot Set (2)

10 60-1317 Side Port Control 20 60-1329 Needle Seal Cartridge*

11 60-1312 Fluid Control Knob

**See air cap selection chart on page 1

*Indicates part included in repair kit # 10-140

TG CONVENTIONAL SPRAY GUN

MATERIAL TYPE FLUID ORIFICE x

AI R C AP

MAXIMUM

PATTERN WIDTH PRESS. / SIPHON

Very Thin

less than 16 sec. Zahn #2

inks , dyes,

solvents, stains

Thin

16 to 20 sec. Zahn #2

lacquers, enamels,

primers, sealers

Medium

21 to 30 sec. Zahn #2

automotive base coat

enamels, primers

epoxies, urethanes

automotive clear coat

Heavy

over 30 sec. Zahn #2

heavy body primers

high solid enamels

high solid automotive coatings

adhesives

1.5, 1.8mm x 2263

1.5, 1.8mm x 2266-3

1.5, 1.8mm x 2466

P/S

0.6, 0.7, 1.0 mm x 2163

0.6, 0.7, 1.0 mm x 2366

0.6, 0.7, 1.0 mm x 2466

1.2, 1.3, 1.5, 1.8 mm x 2263

1.2, 1.3, 1.5, 1.8 mm x 2266

1.2, 1.3, 1.5, 1.8 mm x 2266-3

1.2, 1.3, 1.5, 1.8 mm x 2466

P/S

FLUID NOZZLE / AIR CAP SELECTION CHARTS

TOMAHAWK Series - Pressure / Siphon Feed Guns

0.6, 0.7 mm x 2163

0.6, 0.7 mm x 2166

0.6, 0.7 mm x 2266

Revised 3/18/14

Otros manuales de Pistola pulverizadora de pintura de C.A. Technologies

C.A. Technologies

C.A. Technologies Panther 200H Manual de usuario

C.A. Technologies

C.A. Technologies Lynx L200C Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 200C Manual de usuario

C.A. Technologies

C.A. Technologies Jaguar 300H Manual de usuario

C.A. Technologies

C.A. Technologies H2O-CPR-G Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 300C Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100CVT Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200Z Manual de usuario

C.A. Technologies

C.A. Technologies Lynx 100C Manual de usuario

C.A. Technologies

C.A. Technologies AutoCAT 100CVT Manual de usuario

C.A. Technologies

C.A. Technologies Cougar Manual de usuario

C.A. Technologies

C.A. Technologies CPR Manual de usuario

C.A. Technologies

C.A. Technologies CAT-Xpress Guía de solución de problemas

C.A. Technologies

C.A. Technologies TOMCAT 100C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Lynx 300C Guía de solución de problemas

C.A. Technologies

C.A. Technologies Jaguar 300 Series Manual de usuario

C.A. Technologies

C.A. Technologies H2O-CPR Manual de usuario

C.A. Technologies

C.A. Technologies Tomcat Series Manual de usuario

C.A. Technologies

C.A. Technologies Panther 200C Manual de usuario

C.A. Technologies

C.A. Technologies Panther 100G 1590 Manual de usuario

C.A. Technologies

C.A. Technologies FE-Line LCFM Guía de solución de problemas

C.A. Technologies

C.A. Technologies AutoCAT 100C Manual de usuario

C.A. Technologies

C.A. Technologies CAT SLP Series Manual de usuario

Manuales populares de Pistola pulverizadora de pintura de otras marcas

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manual de usuario

Graco

Graco 246737 Manual de uso y cuidado

Binks

Binks SV100 Manual de usuario

Fimco

Fimco LG-4-3-1 Manual de usuario

AG SPRAY

AG SPRAY FS-ATV-25BL Manual de usuario

Nordson

Nordson MicroMax 2 Manual de usuario

Bonide

Bonide 051 Manual de operación

zogics

zogics Z-DAS Manual de usuario

KISANKRAFT

KISANKRAFT KK-KBS-165 Manual de usuario

Matrix

Matrix SG 650 Manual de usuario

Anest Iwata

Anest Iwata SGA-3 Guía de inicio rápido

paasche

paasche VV Hoja de datos

Carlisle

Carlisle DeVilbiss JGA-510 Manual de usuario

Gardena

Gardena 11120 Manual de usuario

Conrad

Conrad Hobby Airbrush K3 Manual de usuario

wiwa

wiwa 14025 R/F Manual de usuario

Graco

Graco EM 390 Manual de operación

DeVilbiss

DeVilbiss LUNA2i Manual de usuario