Burkert 8045 Manual de usuario
Quickstart
Type 8045
Electromagnetic flowmeter
English
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert SAS, 2012 - 2013
Operating Instructions 1308/1_EU-ML 00563855 ORIGINAL_FR
1. ABOUT THE QUICKSTART.........................................................................3
2. INTENDED USE ................................................................................................4
3. BASIC SAFETY INFORMATION ...............................................................4
4. GENERAL INFORMATION ...........................................................................6
5. DESCRIPTION OF THE NAME PLATE ..................................................6
6. TECHNICAL DATA ...........................................................................................7
7. INSTALLATION AND WIRING .................................................................11
8. ADJUSTMENT, COMMISSIONING .......................................................................... 23
9. MAINTENANCE AND TROUBLESHOOTING ..................................30
10. PACKAGING, TRANSPORT ...................................................................30
11. STORAGE .......................................................................................................30
12. DISPOSAL OF THE PRODUCT ........................................................... 31
3
About the Quickstart
Type 8045
attention
Warns against a possible risk.
• Failure to observe this warning can result in substantial or minor
injuries.
note
Warns against material damage.
•
Failure to observe this warning may result in damage to the device
or system.
Indicates additional information, advice or important
recommendations.
Refers to information contained in this manual or in other
documents.
→Indicates a procedure to be carried out.
1.2. Definition of the word "device"
The word "device" used within this manual refers to the flowmeter
type 8045.
1. ABOUT THE QUICKSTART
The quickstart describes the life cycle of the device. Please keep this
manual in a safe place, accessible to all users and any new owners.
Important safety information.
Respect the safety instructions. Study in particular the chapters
entitled Intended Use and Basic Safety Instructions.
• The quickstart must be read and understood.
The quickstart explains how to install, set, and start-up the device.
A detailed description of the device can be found in the related
operating instructions on the elivered CD.
1.1. Symbols used
danger
Warns against an imminent danger.
• Failure to observe this warning can result in death or in serious
injury.
Warning
Warns against a potentially dangerous situation.
• Failure to observe this warning can result in serious injury or even
death.
English
4
Intended use
Type 8045
2. INTENDED USE
Use of the device that does not comply with the instructions
could present risks to people, nearby installations and the
environment.
• The 8045 flowmeter is intended exclusively to measure flow rate
in liquids.
• This device must be protected against electromagnetic interfer-
ence, ultraviolet rays and, when installed outdoors, the effects of
climatic conditions.
• This device must be used in compliance with the characteristics
and commissioning and use conditions specified in the contrac-
tual documents and in the operating instructions.
• Requirements for the safe and proper operation of the device
are proper transport, storage and installation, as well as careful
operation and maintenance.
• Only use the device as intended.
→Observe any existing restraints when the device is exported.
3. BASIC SAFETY INFORMATION
This safety information does not take into account:
• any contingencies or occurences that may arise during installation,
use and maintenance of the devices.
• the local safety regulations for which the operating company
is responsible including the staff in charge of installation and
maintenance.
Danger due to high pressure in the installation.
• Stop the circulation of fluid, cut off the pressure and drain the
pipe before loosening the process connections.
Danger due to electrical voltage.
• Shut down the electrical power source of all the conductors and
isolate it before carrying out work on the system.
• Observe all applicable accident protection and safety regula-
tions for electrical equipment.
Danger due to high temperatures of the fluid.
• Use safety gloves to handle the device.
• Stop the circulation of fluid and drain the pipe before loosening
the process connections.
Danger due to the nature of the fluid.
• Respect the prevailing regulations on accident prevention and
safety relating to the use of aggressive fluids.
English
5
Basic safety information
Type 8045
Various dangerous situations
To avoid injury take care:
• not to use the device for the measurement of gas flow rates.
• not to use the device in explosive atmospheres.
• not to use the device in an environment incompatible with the
materials it is made of.
• not to subject the device to mechanical loads (e.g. by placing
objects on top of it or by using it as a step).
• not to make any external or internal modifications to the device.
• to prevent any unintentional power supply switch-on.
• to ensure that installation and maintenance work are
carried out by qualified, authorised personnel in possession of
the appropriate tools.
• to guarantee a defined or controlled restarting of the process,
after a power supply interruption.
• to use the device only if in perfect working order and in compli-
ance with the instructions provided in the operating instructions.
• to observe the general technical rules when installing and using
the device.
note
The device may be damaged by the fluid in contact with.
• Systematically check the chemical compatibility of the compo-
nent materials of the device and the fluids likely to come into
contact with it (for example: alcohols, strong or concentrated
acids, aldehydes, alkaline compounds, esters, aliphatic com-
pounds, ketones, halogenated aromatics or hydrocarbons,
oxidants and chlorinated agents).
note
Elements / Components sensitive to electrostatic discharges
• This device contains electronic components sensitive to electro-
static discharges. They may be damaged if they are touched by
an electrostatically charged person or object. In the worst case
scenario, these components are instantly destroyed or go out of
order as soon as they are activated.
• To minimise or even avoid all damage due to an electrostatic
discharge, take all the precautions described in the EN 61340-
5-1 and 5-2 norms.
• Also ensure that you do not touch any of the live electrical
components.
English
6
General information
Type 8045
4. GENERAL INFORMATION
4.1. Manufacturer's address and
international contacts
To contact the manufacturer of the device, use following address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220 TRIEMBACH-AU-VAL
You may also contact your local Bürkert sales office.
The addresses of our international sales offices are available on the
internet at: www.burkert.com
4.2. Warranty conditions
The condition governing the legal warranty is the conforming use of
the 8045 in observance of the operating conditions specified in this
manual.
4.3. Information on the Internet
You can find the user manuals and technical data sheets regarding
the type 8045 at: www.burkert.com
5. DESCRIPTION OF THE NAME
PLATE
Made in France
12 5
67891112
3 4
10
FLOW 8045 SST LONG SUPPLY: 18-36V 300 mA
DO1: 5-36V= 100mA DO2/3:250V 3AMax
DI1: 18-36V= 10mA IP65 Fluid: PN16:-15/110°C
S/N 11 162
00449673 W43M
13
FLOW
14
English
7
Technical data
Type 8045
1. Measured value and type of the device
2. Specification of the flow sensor
3. Specification of the DO1 digital output
4. Specifications of the relay outputs DO2 and DO3
5. Electrical power supply and current consumption
6. Manufacturing code
7. Conformity logo
8. Warning: Before using the device, take into account the tech-
nical specifications described in these operating instructions.
9. Fluid temperature range and fluid nominal pressure
10. Protection class of the device
11. Specification of the DI1 digital input
12. Serial number
13. Order code
14. Shows the flow direction
Fig. 1: Name plate of the 8045 flowmeter
6. TECHNICAL DATA
6.1. Conditions of use
Ambient temperature -10 to +60 °C
Air humidity < 85%, non condensated
Height above see level max. 2000 m
Protection class acc.
to EN 60529
IP65, device wired and cable glands
tightened and cover lid screwed tight.
6.2. Conformity to standards and
directives
The device conforms to the EC directives through the following
standards:
• EMC: EN 61000-6-2, EN 61000-6-3
• LVD: EN 61 010-1
• Vibration: EN 60068-2-6
• Shock: EN 60068-2-27
Pressure: article 3§3 of the Pressure Directive 97/23/CE. Acc. to
the Pressure Directive 97/23/CE: the device can only be used in the
following cases (depending on the max. pressure, the DN of the pipe
and the fluid)
Type of fluid Conditions
Fluid group 1, par. 1.3.a Forbidden
English
8
Technical data
Type 8045
Type of fluid Conditions
Fluid group 2 par. 1.3.a DN ≤ 32
or DN > 32 and PNxDN ≤ 1000
Fluid group 1 par. 1.3.b PNxDN ≤ 2000
Fluid group 2 par. 1.3.b
DN ≤ 200
or PN ≤ 10
or PNxDN ≤ 5000
6.3. Mechanical data
Part Material (8045 with
flow sensor in PVDF)
Material (8045
with flow sensor in
stainless steel)
Housing / seal PC / NBR Black PPA / NBR
Cover with lid /
seal
PC / silicone PSU / silicone
Front foil Polyester
M20x1,5 cable
glands / seal
PA / neoprene
Screws Stainless steel
Nut PC PPA
Flow sensor
(exposed to the
fluid)
PVDF Stainless steel 316L
(DIN 1.4404)
Part Material (8045 with
flow sensor in PVDF)
Material (8045
with flow sensor in
stainless steel)
Seal FKM 8045 with a G2" nut:
FKM
Earth ring of the
flow sensor
Stainless steel 316L
(DIN 1.4404) or Alloy
C22
-
Electrodes holder - PEEK
Electrodes Stainless steel 316L (DIN 1.4404) or Alloy
C22
6.4. General data
Min. fluid conductivity 20 µS/cm
Fluid temperature
• 8045 with flow sensor
in PVDF
• 8045 with flow sensor in
stainless steel
The fluid temperature may be
restricted by the fluid pressure, the
material the flow sensor is made of
and the material the S020 fitting used
is made of.
• 0 to +80 °C
• -15 to +110 °C
English
9
Technical data
Type 8045
Fluid pressure
• 8045 with flow sensor
in PVDF
• 8045 with flow sensor in
stainless steel
The fluid pressure may be restricted
by the fluid temperature, the material
the flow sensor is made of, the
material the S020 fitting used is made
of and the DN of the fitting used.
• PN10
• PN16
10
9
8
7
6
5
4
3
2
1
0
0 +20 +40 +60 +80
PVDF (PN10) /
PP (PN10)
P (bar)
PVC + PP
A
PVC (PN10)
T (°C)
Metal
A: range of use
Fig. 2: Fluid pressure /temperature dependency for a 8045 with
PVDF flow sensor and a fitting S020 in metal, PVC, PVDF
or PP
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0-20 0 +20 +40 +60 +80 +100 +120
PVDF (PN10)
PVC (PN10)
PP (PN10)
T (°C)
P (bar)
PVC + PP
PVDF
A
DN100 for measuring
devices with a clamp con-
nection (PN10)
Metal
(PN16) 1)
1) Except DN100 for measuring devices with a clamp connection
A: range of use
Fig. 3: Fluid pressure /temperature dependency for a 8045 with
stainless steel flow sensor and a fitting S020 in metal,
PVC, PVDF or PP
English
10
Technical data
Type 8045
6.5. Electrical data
Power supply • 18-36 V DC, filtered and
regulated
• oscillation rate: ±5 %
Current consumption 300 mA max. (at 18 V DC)
Transistor output DO1
• type
• function
• frequency
• Electrical data
• duty cycle if f > 2 Hz
• min. pulse duration if
f < 2 Hz
• protections
• NPN / PNP (wiring dependent),
open collector
• pulse output (by default), user
configurable
• 0-250 Hz
• 5-36 V DC, 100 mA max.
• 1/2
• 250 ms
• galvanically isolated, and
protected against over-
voltages, polarity reversals and
short-circuits
Relay outputs (DO2 and
DO3)
• operating
• electrical data of the load
• max. breaking capacity
• life span
• hysteresis (by default), configu-
rable, normally open
• 250 V AC / 3 A or 30 V DC /
3 A (resistive load)
• 750 VA (resistive load)
• min. 100000 cycles
Current output AO1
• specification
• max. loop impedance
• 4-20 mA, sink or source (wiring
dependent), 22 mA to indicate
a fault
• 1300 W at 36 V DC, 1000 W at
30 V DC, 700 W at 24 V DC,
450 W at 18 V DC
Digital input (DI1)
• supply voltage
• input impedance
• min. pulse duration
• protections
• 18-36 V DC
• 15 kW
• 200 ms
• galvanically isolated, and pro-
tected against polarity reversals
and voltage spikes
English
Otros manuales para 8045
8
Tabla de contenidos
Idiomas:
Otros manuales de Instrumento de medición de Burkert
Burkert
Burkert 8746 Manual de usuario
Burkert
Burkert 8756 Manual de usuario
Burkert
Burkert 8026 Manual de usuario
Burkert
Burkert 8032 Manual de usuario
Burkert
Burkert 8026 Manual de usuario
Burkert
Burkert 8756 Manual de usuario
Burkert
Burkert Flowave 8098 Manual de usuario
Burkert
Burkert 8025 Series Manual de usuario
Burkert
Burkert 8640 Manual de usuario
Burkert
Burkert 8221 Manual de usuario
Burkert
Burkert 8756 Manual de usuario
Burkert
Burkert 8026 Manual de usuario
Burkert
Burkert 8202 ELEMENT Manual de usuario
Burkert
Burkert SE36 Manual de usuario
Burkert
Burkert 558129 Manual de usuario
Burkert
Burkert 8020 Manual de usuario
Burkert
Burkert 8200 Series Manual de usuario
Burkert
Burkert 8644 AirLINE Manual de usuario
Burkert
Burkert 8742 Manual de usuario
Burkert
Burkert 8201 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario