Burkert 8045 Manual de usuario
Quickstart
English Deutsch Français
Type 8045
Insertion electromagnetic flowmeter
Magnetisch-induktives Durchfluss-Messgerät, Insertion
Débitmètre électromagnétique à insertion
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert SAS, 2012 - 2019
Quickstart 1904/04_EU-ML 00563855 / Original FR
3
1. ABOUT THE QUICKSTART.........................................................................4
2. INTENDED USE ................................................................................................5
3. BASIC SAFETY INFORMATION ...............................................................5
4. GENERAL INFORMATION ...........................................................................7
5. DESCRIPTION OF THE RATING PLATE ...............................................7
6. TECHNICAL DATA ...........................................................................................8
7. INSTALLATION AND WIRING .................................................................13
8. ADJUSTMENT, COMMISSIONING .......................................................................... 25
9. MAINTENANCE AND TROUBLESHOOTING ..................................32
10. PACKAGING, TRANSPORT ...................................................................32
11. STORAGE .......................................................................................................32
12. DISPOSAL OF THE DEVICE .................................................................32
Type 8045
English
4
About the Quickstart
Type 8045
Caution
Warns against a possible risk.
▶Failure to observe this warning can result in substantial or minor
injuries.
notiCe
Warns against material damage.
Indicates additional information, advice or important
recommendations.
Refers to information contained in this Quickstart or in other
documents.
▶Indicates an instruction to be carried out to avoid a danger, a
warning or a possible risk.
→Indicates a procedure to be carried out.
1.2. Definition of the word "device"
The word "device" used within this Quickstart refers to the insertion
electromagnetic flowmeter type 8045.
1. ABOUT THE QUICKSTART
The Quickstart describes the life cycle of the device. Please keep this
Quickstart in a safe place, accessible to all users and any new owners.
Important safety information.
Respect the safety instructions. Study in particular the chapters
entitled 2. Intended use and 3. Basic safety information.
▶The Quickstart must be read and understood.
▶When the symbol is marked inside or outside the device,
carefully read the Operating Instructions.
The Quickstart explains how to install, set, and start-up the device.
A detailed description of the device can be found in the related
Operating Instructions available on the internet at www.burkert.com
1.1. Symbols used
Danger
Warns against an imminent danger.
▶Failure to observe this warning can result in death or in serious
injury.
Warning
Warns against a potentially dangerous situation.
▶Failure to observe this warning can result in serious injury or
even death.
English
5
Intended use
Type 8045
2. INTENDED USE
Use of the device that does not comply with the instructions
could present risks to people, nearby installations and the
environment.
The insertion electromagnetic flowmeter type 8045 is intended
exclusively to measure flow rate in liquids.
▶This device must be used in compliance with the characteristics
and commissioning and use conditions specified in the contrac-
tual documents and in these Operating Instructions.
▶Never use this device for security applications.
▶This device must be protected against electromagnetic interfer-
ence, ultraviolet rays and, when installed outdoors, the effects of
climatic conditions.
▶Only operate a device in perfect working order.
▶Requirements for the safe and proper operation of the device
are proper transport, storage and installation, as well as careful
operation and maintenance.
▶Only use the device as intended.
3. BASIC SAFETY INFORMATION
This safety information does not take into account:
• any contingencies or occurrences that may arise during instal-
lation, use and maintenance of the devices.
• the local safety regulations for which the operating company is respon-
sible including the staff in charge of installation and maintenance.
Risk of injury due to high pressure in the installation.
▶Stop the circulation of fluid, cut off the pressure and drain the
pipe before loosening the process connections.
Danger due to electrical voltage.
▶If a 18...36 V DC powered version is installed either in a wet environ-
ment or outdoors, all the electrical voltages must be of max. 35 V DC.
▶Disconnect the electrical power for all the conductors and isolate
it before carrying out work on the system.
▶Observe all applicable accident protection and safety regula-
tions for electrical equipment.
Risk of injury due to high fluid temperatures.
▶Use safety gloves to handle the device.
▶Stop the circulation of fluid and drain the pipe before loosening
the process connections.
Risk of injury due to the nature of the fluid.
▶Respect the prevailing regulations on accident prevention and
safety relating to the use of aggressive fluids.
English
6
Basic safety information
Type 8045
Various dangerous situations
To avoid injury take care:
▶not to use the device in explosive atmospheres.
▶not to use the device in an environment incompatible with the
materials it is made of.
▶not to use fluid that is incompatible with the materials the device
is made of.
▶not to subject the device to mechanical loads.
▶not to make any modifications to the device.
▶to prevent any unintentional power supply switch-on.
▶to carry out the installation and maintenance work by qualified
and skilled staff with the appropriate tools.
▶to guarantee a defined or controlled restarting of the process,
after a power supply interruption.
▶to observe the general technical rules when installing and using
the device.
notiCe
The device may be damaged by the fluid in contact with.
▶Systematically check the chemical compatibility of the compo-
nent materials of the device and the fluids likely to come into
contact with it (for example: alcohols, strong or concentrated
acids, aldehydes, alkaline compounds, esters, aliphatic com-
pounds, ketones, halogenated aromatics or hydrocarbons,
oxidants and chlorinated agents).
notiCe
Elements / Components sensitive to electrostatic discharges
▶This device contains electronic components sensitive to electro-
static discharges. They may be damaged if they are touched by
an electrostatically charged person or object. In the worst case
scenario, these components are instantly destroyed or go out of
order as soon as they are activated.
▶To minimise or even avoid all damage due to an electrostatic
discharge, take all the precautions described in the EN 61340-
5-1 norm.
▶Also ensure that you do not touch any of the live electrical
components.
English
7
General information
Type 8045
4. GENERAL INFORMATION
4.1. Manufacturer's address and
international contacts
To contact the manufacturer of the device, use following address:
Bürkert SAS
Rue du Giessen
BP 21
F-67220 TRIEMBACH-AU-VAL
You may also contact your local Bürkert sales office.
The addresses of our international sales offices are available on the
internet at: www.burkert.com
4.2. Warranty conditions
The condition governing the legal warranty is the conforming use of
the 8045 in observance of the operating conditions specified in this
Quickstart.
4.3. Information on the Internet
You can find the Operating Instructions and technical data sheets
regarding the type 8045 at: www.burkert.com
5. DESCRIPTION OF THE RATING
PLATE
FLOW 8045 SST LONG SUPPLY: 18-36V– 300 mA
DO1: 5-36V– 100mA DO2/3: Rel 30V~ or 60V–
DI1: 18-36V– 10mA IP65 Fluid: PN16:-15/110°C
S/N 1000
00570481 W44MU
Made in France
12 5
69101213
3 4
1114 8 7
FLOW
15
English
8
Technical data
Type 8045
1. Measured value and type of the device
2. Specification of the flow sensor
3. Specification of the DO1 digital output
4. Specifications of the relay outputs DO2 and DO3
5. Electrical power supply and current consumption
6. Manufacturing code
7. Conformity marking
8. Warning: before using the device, take into account the tech-
nical specifications described in the Operating Instructions.
9. Certification
10. Fluid temperature range and fluid nominal pressure
11. Protection class of the device
12. Specification of the DI1 digital input
13. Serial number
14. Order code
15. Shows the flow direction
Fig. 1 : Rating plate of the 8045 insertion electromagnetic
flowmeter (example)
6. TECHNICAL DATA
6.1. Conditions of use
Ambient temperature –10...+60 °C
Air humidity < 85 %, non condensated
Height above see level max. 2000 m
Operating conditions Continuous
Equipment mobility Fixed
Use Indoor and outdoor
(Protect the device against electromag-
netic interference, ultraviolet rays and,
when installed outdoors, against the
effects of climatic conditions)
Installation category Category I according to UL/
EN 61010-1
Degree of pollution Degree 2 according to UL/
EN 61010-1
Protection class
according to
IEC / EN 60529
IP65 1), if the device is wired and if the
cable glands are tightened and the
cover lid is screwed tight.
1) not evaluated by UL
English
9
Technical data
Type 8045
6.2. Conformity to standards and
directives
The applied standards, which verify conformity with the EU Direc-
tives, can be found on the EU Type Examination Certificate and/or
the EU Declaration of Conformity (if applicable).
6.3. Conformity to the Pressure
Equipment Directive
→Make sure the device materials are compatible with the fluid.
→Make sure the pipe DN is adapted for the device.
The device conforms to Article 4, Paragraph 1 of the Pressure
Equipment Directive 2014/68/EU under the following conditions:
• Device used on a pipe (PS = maximum admissible pressure;
DN = nominal diameter of the pipe)
Type of fluid Conditions
Fluid group 1, Article 4, Paragraph 1.c.i DN≤25
Fluid group 2, Article 4, Paragraph 1.c.i DN≤32
or PSxDN≤1000
Fluid group 1, Article 4, Paragraph 1.c.ii DN≤25
or PSxDN≤2000
Fluid group 2, Article 4, Paragraph 1.c.ii
DN≤200
or PS≤10
or PSxDN≤5000
6.4. UL certification
The devices with variable key PU01 or PU02 are UL-certified devices
and comply also with the following standards:
• UL 61010-1
• CAN/CSA-C22.2 n°61010-1
Identification
on the device
Certification Variable key
UL recognized PU01
Measuring
Equipment
EXXXXXX
®
UL listed PU02
6.5. Mechanical data
Part Material (8045 with
flow sensor in PVDF)
Material (8045
with flow sensor in
stainless steel)
Housing / seal PC / NBR Black PPA / NBR
Cover with lid /
seal
PC / silicone PSU / silicone
Front foil Polyester
M20x1,5 cable
glands / seal
PA / neoprene
English
10
Technical data
Type 8045
Part Material (8045 with
flow sensor in PVDF)
Material (8045
with flow sensor in
stainless steel)
Screws Stainless steel
Nut PC PPA
Flow sensor
(exposed to the
fluid)
PVDF Stainless steel 316L
(DIN 1.4404)
Seal FKM 8045 with a G2" nut:
FKM
Earth ring of the
flow sensor
Stainless steel 316L
(DIN 1.4404) or Alloy
C22
-
Electrodes holder - PEEK
Electrodes Stainless steel 316L (DIN 1.4404) or Alloy
C22
Rating plate Polyester
6.6. Fluid data
Min. fluid conductivity 20 µS/cm
Fluid temperature
• 8045 with flow sensor in
PVDF
• 8045 with flow sensor in
stainless steel
The fluid temperature may be
restricted by the fluid pressure, the
material the flow sensor is made of
and the material the S020 fitting used
is made of.
• 0...+80 °C
• –15...+110 °C
Fluid pressure
• 8045 with flow sensor in
PVDF
• 8045 with flow sensor in
stainless steel
The fluid pressure may be restricted
by the fluid temperature, the material
the flow sensor is made of, the
material the S020 fitting used is made
of and the DN of the fitting used.
• PN10 1)
• PN16 1)
1) not evaluated by UL
English
Otros manuales para 8045
8
Tabla de contenidos
Otros manuales de Instrumento de medición de Burkert
Burkert
Burkert ELEMENT neutrino 8202 Manual de usuario
Burkert
Burkert 8025 UNIVERSAL Manual de usuario
Burkert
Burkert 8742 Manual de usuario
Burkert
Burkert S030 Manual de usuario
Burkert
Burkert 8202 ELEMENT Manual de usuario
Burkert
Burkert 8756 Manual de usuario
Burkert
Burkert 8035 Manual de usuario
Burkert
Burkert Flowave 8098 Manual de usuario
Burkert
Burkert 8030 Manual de usuario
Burkert
Burkert MS08 Manual de usuario
Burkert
Burkert 8098 FLOWave S Manual de usuario
Burkert
Burkert 8285 Manual de usuario
Burkert
Burkert 8026 Manual de usuario
Burkert
Burkert 8746 Manual de usuario
Burkert
Burkert SE30 Ex Namur Manual de usuario
Burkert
Burkert 8640 Manual de usuario
Burkert
Burkert 8200 Series Manual de usuario
Burkert
Burkert 8026 Manual de usuario
Burkert
Burkert 8020 Manual de usuario
Burkert
Burkert S020 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario