Black Box LB9213A Manual de usuario
Max Express Ethernet Switch
17 Ports 10/100Base-TX/FX
Base Unit: LB9217A-R2
Modules:
LB9213A, LB9214A, LB9215A
LB9216A, LB9218A, LB9219A
LB9220C-ST, LB9220C-SC
Order toll-free in the U.S. 24 hours, 7AM Monday to Midnight Friday: 877-877-BBOX FREE
technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: http://www.blackbox.com· E-mail: info@blackbox.com
CUSTOMER
SUPPORT
INFORMATION
October 2003
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
2
FEDERAL COMMUNICATIONS COMMISSION AND
CANADIAN DEPARTMENT OF COMMUNICATIONS
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been tested and
found to comply with the limits for a Class A computing device in accordance with the
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is operated in a
commercial environment. Operation of this equipment in a residential area is likely to
cause interference, in which case the user at his own expense will be required to take
whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescrites dans le
Règlement sur le brouillage radioélectrique publié par le ministère des Communications
du Canada.
Normas Oficiales Mexicanas (NOM)
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el
aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia
futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación
deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la
tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean
recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
3
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su
uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o
superficie similar puede bloquea la ventilación, no se debe colocar en libreros o
gabinetes que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)
que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del
equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo
particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de
energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado
por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados
sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño;
o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
4
Preface
This manual describes how to install and use the 17-Port modular Fast Ethernet
Switch LB9217A. The switch introduced here is a base unit providing 3 expansion
slots, including two slots for 8-port modules and one slot for single-port module.
The 8-port modules allow for 10/100BaseT/TX or 100BaseFX; the single-port
module allows for 100BaseFX. Over a dozen of TX and FX modules or a
combination of TX/FX are available for fitting the switch. Furthermore, the 17-
Port Switch supports port-based VLAN and MAC-based trunking technologies.
To get the most out of this manual, you should have an understanding of
networking concepts such as bridging, IEEE 802.3u 100BaseTX/FX Fast Ethernet,
and local area networks (LANs).
In this manual, you will find:
•Features on the 17-Port Switch: LB9012A-R2
•Illustrative LED functions
•Installation instructions
•Configuration instructions for VLAN & trunking
•Specifications
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
5
Table of Contents
PREFACE ...........................................................................................4
TABLE OF CONTENTS........................................................................5
INTRODUCTION .................................................................................6
LB9217A: 17-PORT MODULAR FAST ETHERNET SWITCH ...........................6
PRODUCT FEATURES ............................................................................7
PACKING LIST ....................................................................................8
FRONT PANEL FOR BASE UNIT...............................................................8
MODULES...........................................................................................9
MODULE INSTALLATION .....................................................................10
SWITCH CONFIGURATION .............................................................. 14
SETTING UP CONSOLE PORT CONNECTION ............................................. 14
MAIN MENU .....................................................................................15
PORT SETTINGS................................................................................. 16
PORT-BASED VLAN &SETTINGS ......................................................... 17
MAC-BASED TRUNKING &SETTINGS ...................................................18
INSTALLATION................................................................................20
SELECTING A SITE FOR THE SWITCH.....................................................20
CONNECTING TO POWER ..................................................................... 20
CONNECTING TO YOUR NETWORK ........................................................21
TECHNICAL SPECIFICATIONS ........................................................ 22
PHYSICAL SPECIFICATIONS ........................................................... 23
TROUBLE-SHOOTING GUIDE...........................................................24
NO POWER TO THE SWITCH .................................................................24
NO CONNECTIVITY TO THE DATA TERMINAL EQUIPMENT. .......................25
TRANSMISSION PROBLEMS ..................................................................26
GLOSSARY ....................................................................................... 28
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
6
Introduction
LB9217A: 17-Port Modular Fast Ethernet Switch
The 17-Port Switch is a modular switch consisting of three expansion slots: two
for 8-port 10/100BaseTX/FX module, and one for 1-port 100BaseFX module. This
allows the switch to provide up to 17 ports when all the three slots are fit with
modules.
Cost-Effective Migration
The 17-Port Switch is capable of integrating legacy 10Mbps networks with
100Mbps Fast Ethernet networks. In addition, the 17-Port Switch provides an
easy and affordable solution for migrating from copper cabling to fiber
connection when it is equipped with suitable modules to provide both TX and FX
ports.
Flexibility through Modules
Seeing fiber connection become popular while the fiber cabling in small business
environment is still not widespread, the 17-Port Switch is designed to deliver
flexibility through a wide variety of TX and FX modules. Most of the modules
combine TX and FX ports to provide more customization options.
<NOTE> Desired module shall be ordered separately.
Fiber-Connectivity
As a Fast Ethernet switch, the 17-Port Switch is specifically designed to meet the
demanding need for fiber. The switch provides up to 17 ports for 100BaseFX,
multi-mode or single-mode fiber. For multi-mode fiber port, it allows SC, ST,
MT-RJ, VF-45 or LC connector. For single-mode fiber port, it allows SC
connector only. The fiber ports allow maximum segment distance of 75 km when
using single-mode fiber, and therefore, the 17-Port Fiber Switch is an optimum
solution for long distance connection.
Basic Configuration Features
The 17-Port Switch supports port-based Virtual Local Area Networking (VLAN)
and MAC-based trunking technologies. Such advanced features bring network
administrators a powerful yet easy-to-use tool to reduce unnecessary traffic,
efficiently segment the network, and enhance network security.
Standards Compliant
The 17-Port Switch fully complies with IEEE802.3 10BaseT as well as
IEEE802.3u 100BaseTX/FX standards.
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
7
Product Features
♦Base unit with three expansion slots
♦Auto-negotiation for speed and duplexity on TX ports
♦True non-blocking architecture
♦Full wire-speed forwarding rate
♦Store-and-forward mechanism
♦Back-pressure and IEEE 802.3x compliant flow control
♦Supports 8K MAC addresses
♦Supports 4M bits buffer memory
♦Front panel reset button
♦Front panel port status LEDs
♦Standard 19" rack-mount size, one-unit-height
Modules:
♦Allows two 8-port expansion modules: each of up to eight ports for
10/100BaseTX or 100BaseFX
♦Supports auto-MDIX on TX ports of 8-port expansion module
♦Allows one single-port expansion module: one port for 100BaseFX
Connectors:
♦Choices of SC, ST, MT-RJ, VF-45, or LC connectors for 100BaseFX multi-
mode fiber module
♦SC connector allowed for 100BaseFX single-mode fiber module
Basic Configuration Support:
♦Supports port-based VLAN & MAC-based Trunking
♦Programmable re-configuration for fixed speed and duplexity
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
8
Packing List
When you unpack this product package, you will find the items listed below.
Please inspect the contents, and report any apparent damage or missing items
immediately to our authorized reseller.
yThe 17-Port Switch
yUser’s Manual
yAC power cord
yRS232 cable
yRack Mount Ears with screws
Front Panel for Base Unit
The front panel of the 17-port Switch consists of three expansion slots to house
two 8-port modules and one single-port module.
An array of LED indicators on each module provides you with instant feedback on
the status of the switch.
Figure 1: Front View of 17-Port Modular Switch
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
9
Modules
There are total 8 different modules available to choose that fit best with your
network environment needs. Please see the table below for detailed information.
Module Name 10/100RJ45 copper multi-mode fiber
LB9213A 8 0
LB9214A 0 8 (ST)
LB9215A 0 8 (SC)
LB9216A 6 2 (ST)
LB9218A 6 2 (SC)
LB9219A 4 4 (SC)
LB9220C-ST 0 1(ST)
LB9220C-SC 0 1 (SC)
Max Express Ethernet Switch LB9217A-R2 & Applicable Modules
10
Module Installation
There are two sets of different modules available for LB9217A-R2, the base unit
for Max Express Ethernet Switch. Modules LB9213A~LB9219A are equipped
with 8 ports TX/FX while LB9220C-ST & LB9220C-SC are designed with one
fiber port to meet different needs in your network environment. Please see page
9for detailed information.
A B C
Figure 2: Position A & B are designed for 8-port module, position C is for
single port module only
Step by Step Installation for 8-port Module:
LB9213A, LB9214A, LB9215A, LB9216A, LB9218A, LB9219A
1. Remove the module from the static-free container.
2. Unscrew the cover plate(s) from base unit on position A and or B.
3. Remove the plate and keep it for future use if modules need to be removed
later on.
4. With the power off, slide the module(s) into the desired slot, following the
internal plastic guide rails.
5. Once it is slid in fully, snap in the module to make a proper connection
and fasten the screws.
<NOTE> Before you start with any installation, ensure that the power is off.
The module is not hot swappable.
Otros manuales para LB9213A
1
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Enrutador de red de Black Box
Black Box
Black Box LR0003A Manual de usuario
Black Box
Black Box LEH908A Manual de usuario
Black Box
Black Box LPB5028A Manual de usuario
Black Box
Black Box LR9501A Manual de usuario
Black Box
Black Box IC640A Manual de usuario
Black Box
Black Box LT2060A Manual de usuario
Black Box
Black Box LR5100A-T Manual de usuario
Black Box
Black Box InvisaPC DTX1000-T Manual de usuario
Black Box
Black Box LB611A Manual de usuario
Black Box
Black Box LB9002A-ST-R2 Manual de usuario
Black Box
Black Box LB5000A Guía de inicio rápido
Black Box
Black Box LDM-MR128 Manual de usuario
Black Box
Black Box WS100A Manual de usuario
Black Box
Black Box LR9601A Manual de usuario
Black Box
Black Box LEH808 Series Manual de usuario
Black Box
Black Box LRU4240 Manual de usuario
Black Box
Black Box WRT4002A Manual de usuario
Black Box
Black Box LGB1002A-R2 Manual de usuario
Black Box
Black Box LR0019A-4U Manual de usuario
Black Box
Black Box Version 1.0 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad