Black Box LR5000A Manual de usuario

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

DECEMBER 1993

LR5000A

RISC Router Expandable

POWER

RISC Router/2B

FAULT WA N LAN 1 LAN 2

RISC ROUTER EXPANDABLE

PORT

ACTIVITY

FAULT PWR ON

FCC AND IC RFI STATEMENT

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

TRADEMARKS USED IN THIS MANUAL

IPX™ is a trademark, and NetWare®is a registered trademark of

Novell, Incorporated.

VT100™ is a trademark of Eigital Equipment Corporation.

Telnet™ is a trademark of Telnet Communications, Inc.

AMD®is a registered trademark of Advanced Micro Devices Incorporated.

All applied for and registered trademarks are the property of their respective

owners.

Any trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

RISC ROUTER EXPANDABLE

Contents

1.0 SPECIFICATIONS ......................................................................................3

2.0 INTRODUCTION.......................................................................................4

2.1 General Description........................................................................4

2.2 Front-Panel Components ...............................................................6

2.3 Back-Panel Components.................................................................7

2.4 RISC Bridge/E Expansion Card ..................................................10

3.0 INSTALLATION.......................................................................................12

3.1 Unpacking Instructions ................................................................12

3.2 Mounting Instructions..................................................................13

3.2.1 Mounting in a Rack .........................................................13

3.2.2 Table Mounting ...............................................................14

3.3 Network Cables .............................................................................14

3.3.1 DTE (AUI) Interface .......................................................14

3.3.2 Thin Net (BNC) Interface ..............................................15

3.3.3 RS-232 Interface...............................................................16

3.3.4 RS-449 Interface...............................................................16

3.4 Network Installation .....................................................................17

3.4.1 Connecting an RS-232 Terminal to

the Control Port...............................................................17

3.4.2 DTE (AUI) Connection ..................................................18

3.4.3 BNC Connection .............................................................18

3.4.4 MAU Connection ............................................................19

3.4.5 Wide-Area Network Connection.....................................20

3.5 AC Connection..............................................................................23

4.0 UPGRADES ..........................................................................................24

4.1 PROM Card Installation ...............................................................24

4.2 Expansion Card Installation.........................................................26

5.0 TROUBLESHOOTING............................................................................29

5.1 Troubleshooting Steps..................................................................29

CHAPTER 1: Specifications

1.0 Specifications

Processor — AMD 29000

Clocking Rate — 20 MHz

Line Rate — 10 Mbps

Data Rate — 20 Megabytes per second

Buffer Memory — 1/2 to 2 MB

Ethernet

LAN Interface — 1-8 IEEE 802.3; Ports configured as:

DTE (AUI): Female DB15;

Thin Ethernet: BNC barrel connector;

MAU: Male DB15

WAN Interface — (2) RS-449 Serial ports configured as EIA-530,

V.35, or RS-232

Control Port

Interface — RS-232 (local/modem connection)

Max. Filtering

Rate — 90,000 packets per second (64-byte packets)

Max. Forwarding

Rate — 56,000 packets per second (64-byte packets)

Power — 90 to 132 or 175 to 264 VAC (47 to 440 Hz)

Size — 5.3"H x 17.5"W x 14"D (13.5 x 44.5 x 35.6 cm)

Weight — 23 lb. (10.4 kg)

RISC ROUTER EXPANDABLE

2.0 Introduction

This chapter describes the RISC Router Expandable inter-networking

platform, and contains information on the following:

• Major components

• Connectors (with pin assignments)

• Cables (with pin assignments)

• Hardware specifications

2.1 General Description

The RISC Router Expandable is a state-of-the-art RISC-based intelligent

bridge/router, employing the AMD®29000 microprocessor. The RISC Router

Expandable is a transparent network inter-connection device operating on

the MAC layer, level 2, of the OSI model. The RISC Router Expandable

currently routes TCP, IP, IPX™, and XNS protocols and bridges all others.

With eight Ethernet expansion slots, the RISC Router Expandable supplies

a variety of mixed-media hardware interfaces. The RISC Bridge/E Expansion

Card (LB521C) supports three interfaces:

• A Media-Access Unit (MAU) interface — a standard 15-pin male

connector. You can connect a workstation directly to this interface.

• A ThinNet (BNC) interface — a standard Thin Ethernet connection.

•A Data Terminal Equipment (DTE) interface — a standard 15-pin

female connector for a transceiver.

NOTE

IEEE 802.3 and Ethernet v.2 are identified as simply “Ethernet”

in this text.

The RISC Router Expandable delivers maximum bandwidth at 10 megabits per

second across eight individual LAN Ethernet ports. Peak filtering rates of up to

90,000 64-byte packets per second and forwarding at full Ethernet line speeds

of 56,000 64-byte packets per second are achieved under ideal conditions.

For wide area network connection, the RISC Router Expandable provides two

RS-449 serial links. The WAN interface supplies two high-speed transparent

serial channels operating at 384 Kbps. These channels provide a single logical

connection to a remote RISC Router Expandable while balancing the traffic

load over the two channels.

CHAPTER 2: Introduction

The RISC Router Expandable currently supports the following wide-area

network protocols:

• X.25

• Frame Relay

• Point-to-point

• HDLC raw

The RISC Router Expandable is equipped with 1 CPU board, 1 PROM card,

and up to eight expansion cards. A network control port is standard and

supports a user-interface via any VT100™ compatible terminal. Each Ethernet

card is equipped with an Ethernet terminator switch. The RISC Router

Expandable operates on 90-132/175-264 VAC, (47-440 Hz) and meets all

regulatory power-safety requirements.

The Network Control program is the user interface to the RISC Router

Expandable and provides the software tools for the internetworking platform.

Depending on the hardware and software configuration of the RISC Router

Expandable, Network Control provides the following:

• TCP/IP routing, IPX/NetWare®routing

• Protocol-transparent, high-speed bridging

• Multiple logical bridges

• Ethernet switching

• Telnet™, SNMP

• Spanning Tree

• Custom-address filtering

• Network statistics

• Password-protected security

RISC ROUTER EXPANDABLE

2.2 Front-Panel Components

This section describes the front panel of the RISC Router Expandable.

The numbers in Figure 2-1 correspond to the numbered descriptions below:

1. Port Activity LEDs — The Port Activity LEDs (green) indicate traffic on

the ports of the RISC Router Expandable. Each port has a corresponding

LED that lights when that port is active. The ports are shown from 1

through 8.

2. FAULT LED — The FAULT LED (amber) indicates a software problem.

The software triggers a hardware timer once a second. If it fails to do so,

the FAULT LED lights.

3. PWR OK LED — The PWR OK LED is green when the unit is ON.

Figure 2-1. Front Panel of the RISC Router Expandable.

PORT

ACTIVITY

FAULT PWR OK

1 2 3

RISC ROUTER EXPANDABLE

CHAPTER 2: Introduction

2.3 Back-Panel Components

This section describes the back panel components of the RISC Router

Expandable. The numbers in Figure 2-2 correspond to the numbered

descriptions below:

1. AC Power Port — The AC power port is a three-pronged grounded AC

input port for the RISC Router Expandable. The unit uses 110 or 220

VAC and automatically configures to the appropriate voltage.

2. ON/OFF Switch — The ON/OFF switch provides power to the RISC

Router Expandable. The “1” indicates ON. The “0” indicates OFF.

3. Reset Switch — The switch is reserved for future use.

4. FAULT LED — The FAULT LED (amber) indicates a software problem.

The software triggers a hardware timer once a second. If it fails to do so,

the FAULT LED lights. This LED is the same as the FAULT LED on the

front of the RISC Router Expandable.

5. Wide Area Network (WAN) Port(s) — The two WAN ports provide

remote transparent bridging. Each WAN port has a male DB37

connector. You can jumper the signaling on the two ports to meet either

RS-423/RS-232, RS-422, or V.35. The signal definitions for the EIA-530

specification follow the RS-422 specification. The V.35-compatible

interface is typically an M-block connector. The pin assignments for

these connectors are in Table 2-1.

6. RS-232 Serial Port — The RS-232 serial port is a DB25 connector used

to provide access to the Network Control program via VT100 compatible

terminal. The pin assignments used in the RISC Router Expandable

RS-232 port are listed in Table 2-2.

Figure 2-2. Back Panel of the RISC Router Expandable.

1 2 3 4

RISC ROUTER EXPANDABLE

Table 2-1. Pin Assignments for the Wide Area Network Port.

RS-449 EIA-530 RS-232 V.35 Circuit

1 1 1 A Shield

2 — 12 — Signaling Rate

3 — — — Spare

4 2 2 P Send Data (D)

5 15 15 Y Send Timing (A)

6 3 3 R Receive Data (A)

7 4 4 C Request To Send

8 17 17 V Receive Timing (A)

9 5 5 D Clear To Send (A)

10 18 — — Local Loopback

11 6 6 E Data Set Ready (A)

12 20 20 E Terminal Ready (A)

13 8 8 F Receiver Ready (A)

14 21 — — Remote Loopback

15 — 22 — Incoming Call

16 — 23 — Select Frequency

17 24 24 U Terminal Timing (A)

18 25 — — Test Mode

19 7 7 B Signal Ground

20 — 7 B Receive Ground

21 — — — Spare

22 14 — S Send Data (B)

23 12 — AA Send Timing (B)

24 16 — T Receive Data (B)

25 19 — — Request To Send (B)

26 9 — X Receive Timing (B)

27 13 — — Clear To Send (B)

28 — 25 — Terminal Service

29 22 — — Data Set Ready

30 23 — — Terminal Ready (B)

31 10 — — Receiver Ready (B)

32 — — — Select Standby

33 — 21 — Signal Quality

34 — 18 — New Signal

35 11 — W Terminal Timing (B)

36 — — — Standby Indicator

37 — 7 B Send Common

Tabla de contenidos

Otros manuales de Enrutador de red de Black Box

Black Box

Black Box LDM-MR128 Manual de usuario

Black Box

Black Box LB9007A-ST-R3 Manual de usuario

Black Box

Black Box VOE212 Manual de usuario

Black Box

Black Box LBU2090 Manual de usuario

Black Box

Black Box VOE231 Manual de usuario

Black Box

Black Box WRT750A Manual de usuario

Black Box

Black Box WS100A Manual de usuario

Black Box

Black Box LT2060A Manual de usuario

Black Box

Black Box VOE210 Series Manual de usuario

Black Box

Black Box LR0003A Manual de usuario

Black Box

Black Box L2 Plus Manual de usuario

Black Box

Black Box LB8415A-US Manual de usuario

Black Box

Black Box LR9601A Manual de usuario

Black Box

Black Box LGB4005A Manual de usuario

Black Box

Black Box LR0002A-BSDN Manual de usuario

Black Box

Black Box LR1102A-T1/E1 Manual de usuario

Black Box

Black Box WRT4002A Manual de usuario

Black Box

Black Box 1000 Series Manual de usuario

Black Box

Black Box LB308A Manual de usuario

Black Box

Black Box LR5100A-T Manual de usuario

Black Box

Black Box LR120A Manual de usuario

Black Box

Black Box IC469A Manual de usuario

Black Box

Black Box LEH1008A Manual de usuario

Black Box

Black Box LB9017A-R2 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad