Cisco NCS 540 Manual

Cisco Network Convergence System 540 Large Density Routers

Hardware Installation Guide

First Published: 2021-06-02

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

CONTENTS

Safety Warnings 1

CHAPTER 1

Standard Warning Statements 1

Safety Guidelines for Personal Safety and Equipment Protection 2

Safety with Electricity 3

Cautions and Regulatory Compliance Statements for NEBS 4

Power Supply Considerations 5

Power Connection Guidelines 5

Guidelines for DC-Powered Systems 6

Guidelines for AC-Powered Systems 6

Preventing ESD Damage 6

Cisco NCS 540 Large Density Routers Overview 9

CHAPTER 2

Features 9

Specification 10

Interface Naming 10

Network Timing Interfaces 11

GNSS Receiver 11

GNSS Receiver RF Input Requirements 11

External Alarm Inputs 12

Console 13

USB Console 13

Online Insertion and Removal 13

Supported Transceiver Modules 13

Prepare for Installation 15

CHAPTER 3

General Precautions 15

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

iii

Site Planning Checklist 16

Environmental Requirements 16

Airflow Guidelines 16

Recommended Airflow 18

Site Power Guidelines 18

Electrical Circuit Requirements 19

Site Cabling Guidelines 19

Asynchronous Terminal Connections 20

Interference Considerations 20

Electromagnetic Interference 20

Radio Frequency Interference 20

Lightning and AC Power Fault Interference 20

Tools and Equipment 20

Prepare Your Location 21

Prepare Yourself 22

Prepare Rack for Router Installation 23

Cabinet Selection Guidelines 24

Unpack the Cisco NCS 540 Large Density Routers 25

Install the Device 27

CHAPTER 4

Rack Compatibility 27

Rack Types 28

Set up Device on Rack 30

Rack Mount 30

Ground the Device 35

Install the AC Power Cables 36

Activate an AC Power Supply Module 37

Install the DC Power Cables 38

Activate a DC Power Supply Module 39

Port Connection Guidelines 39

Connect to the Console Port 40

Connect to the Management Ethernet Port 42

Connecting Timing Cables 43

Connecting a Cable to the Input 10MHz or 1PPS Interface 43

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Contents

Connecting a Cable to the Output 10MHz or 1PPS Interface 44

Connecting a Cable to the GNSS Antenna Interface 44

Install and Remove Transceiver Module 45

Safety Precautions for Module Installation and Removal 45

Install and Remove SFP56, SFP28, SFP10, and SFP Modules 45

Bale Clasp SFP56, SFP28, SFP10, and SFP Module 46

Install a Bale SFP56, SFP28, SFP10, and SFP Module 47

Remove a Bale Clasp SFP56, SFP28, SFP10, and SFP Module 48

Install and Remove QSFP+, QSFP28, or QSFP-DD Transceiver Modules 49

Required Tools and Equipment 52

Install the 40-Gigabit QSFP+, 100-Gigabit QSFP28, or 200/400-Gigabit QSFP-DD Transceiver

Module 52

Attach the Optical Network Cable 53

Removing the 40-Gigabit QSFP+, 100-Gigabit QSFP28, or 200/400-Gigabit QSFP-DD Transceiver

Module 54

Connect Interface Ports 55

Connect a Fiber-Optic Port to the Network 55

Disconnect Optical Ports from the Network 55

Maintain Transceivers and Optical Cables 56

Configure the Device 57

CHAPTER 5

Create the Initial Router Configuration 57

Verify Device Installation 59

Replace Power Supply 61

CHAPTER 6

Remove the DC Power Supply Module 61

Install the DC Power Supply Module 62

Remove the AC Power Supply Module 63

Install the AC Power Supply Module 64

Appendix 65

CHAPTER 7

LEDs 65

Router LEDs 65

System Fans LED 66

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Contents

Power Status LEDs 67

Power Supply LEDs (PM0/PM1) 67

Front Panel Power LED and Fan LED Combination 68

System Specifications 68

Weight and Power Consumption 69

Environmental Specifictaions 69

Transceiver and Cable Specifications 69

RJ-45 Connectors 69

Console Port Pinouts 69

Management Ethernet Port Pinouts 70

Timing Port Pinouts 70

Time-of-Day Port Pinouts 71

USB Port Pinouts 71

Alarm Port Pinouts 72

AC Power Cord Specifications 72

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Contents

CHAPTER 1

Safety Warnings

This handout lists the safety warnings necessary for handling this chassis. Before you install or service the

chassis, review these safety warnings to avoid injuring yourself or damaging the equipment.

For a complete list of translated safety warnings, see the Regulatory Compliance and Safety Information —

Cisco NCS 500 Series Routers document.

The safety warnings are grouped under the following sections:

•Standard Warning Statements, on page 1

•Safety Guidelines for Personal Safety and Equipment Protection, on page 2

•Safety with Electricity, on page 3

•Cautions and Regulatory Compliance Statements for NEBS, on page 4

•Power Supply Considerations, on page 5

•Preventing ESD Damage, on page 6

Standard Warning Statements

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only

by using a special tool, lock and key, or other means of security. Statement 1017

Warning

Ultimate disposal of this product must be handled according to all national laws and regulations. Statement

1040

Warning

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended

ambient temperature of –40C to +65C. Statement 1047

Warning

Mount the device on a rack that is permanently affixed to the building. Statement 1049

Warning

This device is a Class A Device and is registered for EMC requirements for industrial use. You must be aware.

If sold or purchased by mistake, do replace with a residential-use type. Statement 294

Warning

This equipment needs to be grounded. Use a green and yellow 6AWG ground wire to connect the host to earth

ground during normal use. Statement 383

Warning

Do not stare into the beam or view it directly with optical instruments. Statement 1011

Warning

Invisible laser radiation present. Statement 1016

Warning

The plug-socket combination must be accessible at all times, because it serves as the main disconnecting

device. Statement 1019

Warning

SafetyGuidelines forPersonalSafety andEquipmentProtection

The following guidelines ensure your safety and protect the equipment. This list does not include all the

potentially hazardous situations. Therefore, you must be alert.

• Before moving the system, always disconnect all power cords and interface cables.

• Never assume that power is disconnected from a circuit; always check.

• Before and after installation, keep the chassis area clean and dust free.

• Keep tools and assembly components away from walk areas where you or others can trip over them.

• Do not work alone if potentially hazardous conditions exist.

• Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

• Do not wear loose clothing that may get caught in the chassis.

• When working under conditions that may be hazardous to your eyes, wear safety glasses.

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Safety Warnings

Safety Guidelines for Personal Safety and Equipment Protection

Safety with Electricity

Before working on a chassis or with power supplies, unplug the power cord on AC units. Disconnect the

power at the circuit breaker on DC units. Statement 12

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces,

and watches). Metal objects heat up when connected to power and ground and can cause serious burns or

weld the metal object to the terminals. Statement 43

Warning

Read the installation instructions before connecting the system to the power source. Statement 1004

Warning

The plug-socket combination must be accessible always, because it serves as the main disconnecting device.

Statement 1019

Warning

This unit may have more than one power supply connection. All connections must be removed to de-energize

the unit. Statement 1028

Warning

When installing or replacing the unit, ensure the ground connection first and disconnected last. Statement

1046

Warning

This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that

the switch functional ground lug is connected to earth ground during normal use. Statement 1064

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

When working on equipment that is powered by electricity, follow these guidelines:

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Safety Warnings

Safety with Electricity

• Locate the room’s emergency power-off switch. If an electrical accident occurs, you know where to

quickly turn off the power.

• Before starting work on the system, turn off the DC main circuit breaker and disconnect the power

terminal block cable.

• Disconnect all power when:

• Working on or near power supplies

• Installing or removing a device chassis or network processor module

• Performing most hardware upgrades

• Never install equipment that appears damaged.

•Carefully examine your work area for possible hazards, such as moist floors, ungrounded power extension

cables, and missing safety grounds.

• Never assume that power is disconnected from a circuit; always check.

• Never perform any action that creates a potential hazard to people or makes the equipment unsafe.

• If an electrical accident occurs and you are uninjured:

• Use caution to avoid injuring yourself.

• Turn off power to the device.

• Seek medical attention, if necessary.

Use the following guidelines when working with any equipment that is disconnected from a power source,

but connected to telephone wiring or network cabling:

• When installing or modifying telephone lines, use caution.

• Never install telephone jacks in wet locations unless the jack is designed to handle such locations.

• Never install telephone wiring during a lightning storm.

Cautions and Regulatory Compliance Statements for NEBS

The NEBS-GR-1089-CORE regulatory compliance statements and requirements are discussed in this section.

The intrabuilding port(s) of the equipment or subassembly, which is the management Ethernet port, must use

shielded intrabuilding cabling/wiring that is grounded at both ends. Statement 7003

Warning

Cisco Network Convergence System 540 Large Density Routers Hardware Installation Guide

Safety Warnings

Cautions and Regulatory Compliance Statements for NEBS

Otros manuales para NCS 540

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco 8011 Manual de usuario

Cisco

Cisco ASR 5000 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco 3700 - 32 To 128MB Manual

Cisco

Cisco 3825 Series Manual de servicio

Cisco

Cisco RV260 series Manual de instrucciones

Cisco

Cisco 800 Series Guía

Cisco

Cisco 6000 series Manual técnico

Cisco

Cisco ASR 5000 Series Manual de instrucciones

Cisco

Cisco Cisco 888 Manual

Cisco

Cisco 7204 - VXR Router Manual de instrucciones

Cisco

Cisco 7401ASR Manual del operador

Cisco

Cisco MGX 8850 (PXM1E/PXM45) Manual de usuario

Cisco

Cisco 4451 ISR Manual

Cisco

Cisco ASR 1000 Series Manual

Cisco

Cisco Linksys E4200 Manual de usuario

Cisco

Cisco Soho 78 Manual de usuario

Cisco

Cisco RV120W Manual de usuario

Cisco

Cisco VS-C6509E-S720-10G Manual de usuario

Cisco

Cisco RV180 Manual de uso y cuidado

Cisco

Cisco 2691 Series Manual de usuario

Cisco

Cisco Catalyst 2960 Series Manual de usuario

Cisco

Cisco 1841 - 1841 Integrated Services Router Manual

Cisco

Cisco 5915 Guía de inicio rápido

Cisco

Cisco 7513 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario