Billion BiPAC 8501 R3 Manual de usuario

BiPAC 8501 R3/ 8521 R3

SHDSL.bis Firewall Bridge/ Router

Quick Start Guide

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router

Package Contents

BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/ Router

CD-ROM containing the online manual

RJ-11 SHDSL/ telephone Cable (Note: BiPAC 8521 R3 contains two RJ-11 cables)

Ethernet (RJ-45) Cable

Power adapter

This Quick Start Guide

For more detailed instructions on configuring and using the

Billion SHDSL.bis Firewall Bridge/ Router, please refer to the

on-line manual.

Do not use the BiPAC 8501 R3/ 8521 R3 in high humidity or high

temperatures.

Do not use the same power source for this router as other

equipment.

Do not open or repair the case yourself. If this router is too hot,

turn off the power immediately and have it repaired at a qualified

service center.

Avoid using this product and all accessories outdoors.

Warning

Place this router on a stable surface.

Only use the power adapter that comes with the package. Using a

different voltage rating power adaptor may damage this router.

Attention

Quick Start Guide

The Front LEDs of BiPAC 8501 R3

LED Status Meaning

Red Boot failure or in emergency mode

1 Power

Green System ready

Green Transmission speed at 10/100Mbps

2 Ethernet 1 ~ 4

(EWAN - LAN 4)

Blinking Data being transmitted/received

Green Blinking DSL synchronizing or waiting for DSL synchronizing

Green Successfully connected to an SHDSL DSLAM (Line Sync).

3 DSL

Off DSL cable unplugged

Green Router is IP connected and data is transmitting

Red Router is not IP connected or in Bridge mode

4 Internet

Off SHDSL connection not present.

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router

The Front LEDs of BiPAC 8521 R3

The Rear Ports of BiPAC 8501 R3

LED Status Meaning

Red Boot failure or in emergency mode

1 Power

Green System ready

Green Transmission speed at 10/100Mbps

2 Ethernet 1 ~ 4

(EWAN - LAN 4)

Blinking Data being transmitted/received

Green Blinking DSL synchronizing or waiting for DSL synchronizing

Green Successfully connected to an SHDSL DSLAM (Line Sync).

3 DSL 1 ~ 2

Off DSL cable unplugged

Green Router is IP connected and data is transmitting

Red Router is not IP connected or in Bridge mode

4 Internet

Off SHDSL connection not present.

Quick Start Guide

Port Meaning

1 Power Switch Power ON / OFF switch.

2 Power Connect the supplied power adapter to this jack.

3 Reset

After the device is powered on, press it 6seconds or above: to restore to factory

default settings (this is used when you cannot login to the router, e.g. forgot the

password)

4 Ethernet 1 ~ 4

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when

connecting to a PC or an office/home network of 10Mbps /100Mbps.

Note: Port #4 can be configured as a WAN Interface for Broadband connectivity.

5 DSL Connect this port to the SHDSL.bis network with the RJ-11 telephone cable

provided.

The Rear Ports of BiPAC 8521 R3

Port Meaning

1 Power Switch Power ON / OFF switch.

2 Power Connect the supplied power adapter to this jack.

3 Reset

After the device is powered on, press it 6seconds or above: to restore to factory

default settings (this is used when you cannot login to the router, e.g. forgot the

password)

4 Ethernet 1 ~ 4

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when

connecting to a PC or an office/home network of 10Mbps /100Mbps.

Note: Port #4 can be configured as a WAN Interface for Broadband connectivity.

5 DSL 1 ~ 2 Connect this port to the SHDSL.bis network with the RJ-11 telephone cable

provided.

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router

Connecting Your SHDSL.bis Bridge/ Router

1. Connect the Router to an Ethernet (Local Area Network) and the DSL (SHDSL Line).

2. Power on the device.

3. Make sure the Power, DSL and Internet LEDs are lit steadily and that the relevant Ethernet

LED are lit.

Quick Start Guide

Factory Default Settings

Before configuring the bridge/router, you need to know the following default settings.

Device LAN IP settings

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

Web Interface: (Username and Password)

Username: admin

Password: admin

The default username and password are “admin” and “admin” respectively.

Please see the relevant sections of on-line manual for detailed instructions

on how to configure your router.

If you ever forget the username/password to login to the router, you may

press the RESET button up to 6seconds then release it to restore the

factory default settings.

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router

Troubleshooting

1. None of the LEDs are on when you turn on the router.

Check the connection between the adapter and the router. If the error persists, you may have

a hardware problem. In this case you should contact technical support.

2. Can’t ping any PCs on the LAN.

Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC

connected. If it is off, check the cables between your router and the PC. Make sure you have

uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet

mask are consistent between the router and the workstations.

3. Frequent loss of DSL line sync (disconnections).

Ensure that all other devices connected to the same telephone line as your router (e.g.

telephones, fax machines, analogue modems) have a line filter connected between them and

the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified

and licensed electrician), and ensure that all line filters are correctly installed and the right

way around. Missing line filters or line filters installed the wrong way around can cause

problems with your DSL connection, including causing frequent disconnections. If you have a

back-to-base alarm system you should contact your security provider for a technician to make

any necessary changes.

4. You have forgotten your router login and/or password.

Try the default login and password, please refer to User Manual. If this fails, you can restore

your router to its factory settings by holding the Reset button on the back of your router for 6

seconds or more.

Product Support and Contact Information

Most problems can be solved by referring to the Troubleshooting section in the User Manual.If

you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer

where you purchased this product.

Contact Billion

WORLDWIDE

http://www.billion.com

BiPAC 8501R3/8021R3 V.1.010

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Billion

Billion

Billion BiPAC 710C2 Manual de usuario

Billion

Billion BiPAC 7300N Manual de usuario

Billion

Billion BiPAC 7700N Manual de usuario

Billion

Billion BiPAC 7800(N) Manual de usuario

Billion

Billion BiPAC 6404VP Manual de usuario

Billion

Billion BiPAC 8501 Manual de usuario

Billion

Billion Modem/Router ADSL BIPAC-7100 Guía

Billion

Billion BiPAC 5210S RC Manual del propietario

Billion

Billion BiPAC 5210S Manual de usuario

Billion

Billion BiPAC 7402GL R4 Manual de usuario

Billion

Billion BiPAC 5100 Manual de usuario

Billion

Billion 800VGT Manual de usuario

Billion

Billion BiPAC 8206AZ Manual de usuario

Billion

Billion BiPAC 8700NEXL R2 Manual de usuario

Billion

Billion BIPAC 7100G Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

Billion

Billion BiPAC 8500 Manual de usuario

Billion

Billion BiPAC 8900AX-1600 R2 Manual de usuario

Billion

Billion BiPAC 645 Manual de usuario

Billion

Billion BiPAC 5200W RC Manual de usuario

Billion

Billion BiPAC 4500NZ(L) Manual de usuario

Billion

Billion BiPAC 7402G Manual de usuario

Billion

Billion BiPAC 7800(N) Manual de usuario

Billion

Billion BiPAC 7404VGOX Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

LevelOne

LevelOne FBR-1416 Manual de usuario