AWS DIA-20 Manual de usuario

Tabla de contenidos

Manuales populares de Escala de otras marcas

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario

DIA-20 Precision Pocket Scale

20g x 0.001g

USER’S MANUAL

American Weigh Scales, Inc.

American Weigh

DIA-20 User’s Manual

20g x 0.001g

Thank you for purchasing the DIA-20 Precision Digital Pocket Scale.

Please read all operating instructions carefully before use. Scales are

precision instruments and should always be handled with proper care.

To ensure years of reliable service, keep these simple tips in mind:

• Do not exceed the scales maximum capacity. Overloading your scale

can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales perform best at

normal room temperature. If temperatures have changed dramatically,

recalibration may be necessary.

• Allow your scale to warm up for 30-60 seconds before performing

calibration (if available).

• Store your scale in a clean, dry location. Dust, dirt, and moisture

can accumulate on the weighing sensors and electronics causing

innacuracy or malfunction.

• Avoid using your scale in close proximity to strong radio wave

emitting devices such as computers, cash registers, and cordless

phones.

• Always weigh on a at and level surface, free from vibrations and

drafts. The corner of a room is usually the most stable.

• Gently apply all items to be weighed. Do not drop items onto the

weighing platform.

• Avoid dropping your scale. The warranty does not cover damage due

to rough treatment or overload.

I. Operation

Place the scale on a at and stable surface.

1. Press ON/OFF key.

2. Wait until [0.0] is displayed.

3. Put the object(s) on the weighing platform.

4. Using the MODE key, you can switch between the weighing units.

II. Tare Weighing.

1. Turn on scale as described above.

2. Place the “tare item” on the platform.

3. Press TARE and wait until [0.0] is displayed.

4. Add the “net-weight-item”.

III. Add-Up Feature

1. In normal weighing mode, place an object on the platform

2. Once weight is displayed, press “ADD UP” key and replace item with

another and press “ADD UP” again

3. The scale will display the sum of the two weights.

4. You may repeat until scale reaches max capacity ( display will show

“0” when capacity is exceeded )

IV. Calibration

1. Turn the scale on as described above and wait for the display to

show “0.000g”.

2. Press and hold the TARE key until the display shows “CAL” then a

random number will be displayed (ISN number).

3. Make sure no weight is on the platform and press the TARE key

again. The display will ash CAL followed by “0.000g”.

4. Now place a 10g calibration weight on the platform and press TARE

again when the number stabilizes. The display will ash “10.000g”

followed by the ISN number again.

5. At this point, place another 10g on the platform to make a total of

20g on the scale and press TARE when the number stabilizes.

6. The display will show “20.000g” followed by “PASS”. Press ON/OFF

to turn the scale off and accept the calibration. Calibration is complete!

V. Troubleshooting

The primary reason for innaccuracy or malfunction are low

batteries, improper calibration, overload or operating on an

unstable surface. Please keep this in mind and maintain

and operate your scale properly. This scale is a precision

instrument and must be handled with care.

Error Code Descriptions:

Error: Nothing on screen, [LO],

Solution: Replace Batteries

Error: [EEEE]

Solution: Load is in excess of 20g, remove the extra load.

VI. Specications

Capacity: 20g; 100ct; 308.8gn; 12.86dwt

Graduation: 0.001g; 0.005ct; 0.02gn; 0.001dwt;

Units: grams (g) / carats (ct) /

grains (gn) pennyweight (dwt)

Calibration: Auto Calibration; User Calibration with (2)10g

weights

Tare Range: Tare full capacity

Auto Off: 60 seconds

Display: 5 digits 1/2” in height