AWS LS-110 Manual de usuario

American Weigh Scales

LS-110 (110lb x 0.2lb)

User Manual

LS-110

LS-110 Manual

Thank you for purchasing the American Weigh

LS-110 luggage scale. Please read all operating instructions

carefully before use. Scales are precision measuring devices

and should always be handled with proper care. To ensure

years of reliable service, keep these simple tips in mind:

• Do not exceed the scale’s maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, calibration

and adjustment may be necessary.

• Allow your scale to warm up for 30-60 seconds before

performing calibration and adjustment (if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing inaccuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Alwaysweighonaatandlevelsurface,freefrom

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

• Checkthebatteriesrstifyouarehavinganytrouble

with your scale. This simple step can remedy most

scale issues.

• Do not disassemble your scale. This product contains

no user serviceable parts.

I. Part List

1. Scale

2. Weighing Tray

3. AAA Batteries (x2)

II. Key Description

III. Battery Installation

1. Beforeusingthescaleforthersttime,check

the battery compartment and remove any plastic

insulation strips or packaging that may be in place to

prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the

positive and negative contacts are properly aligned.

ON/OFF

TARE Key

ON/OFF

Lock

Positive Side

Facing Out

LS-110 Manual

IV. Operation

1. Set the ON/OFF Lock switch to the ON position and

then tap the key to turn the scale on.

2. Once the start-up process completes and the scale

goes to zero, you are ready to weigh.

3. Place the quantity to be weighed on the weighing

hook.

4. Once the weight has stabilized, a red light will

illuminate on the top of the scale and the LCD will

display HOLD above the weight.

5. The weight will remain on the display after the item

is removed from the hook. To re-zero the scale, tap

the key.

6. Once weighing is complete, hold the key to turn

the scale off then set the ON/OFF Lock switch to the

OFF position.

V. Changing the Unit of Measure

This scale can read in KG or LB. To change the weighing

mode, follow these instructions:

1. Tap the key to turn the scale on, then

immediatedly press the key again and hold it for

2-3 seconds until the weighing unit is displayed,

then release.

2. Now tap the key to change the weighing unit

between KG or LB.

3. After a couple of seconds the scale will enter normal

weighing mode.

• LS-110 Units: kg (kilogram) lb (pound)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight

of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the

available capacity.

1. Turn on the scale as described in Section IV.

2. Attach your tare item / empty container using

the hook and wait for it to stabilize (HOLD will be

displayed).

3. Tap the button. “0.0” will be displayed.

4. You can now add items to the container to obtain

just the weight of the contents.

5. When the container is removed the weight will be

held on the display. Press again to zero the scale.

VII. Calibration

Calibration and adjustment are performed at the factory.

However, the weighing range can shift slightly during

shipping. Also, due to changes in local acceleration of gravity

around the world, adjustment is recommended when moving

the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale

and note the displayed value.

2. If the displayed value is not within acceptable

tolerance (see chart on next page), adjustment is

required.

Model Acceptable

Tolerance (±)

Calibration

Weight

Recommended

Accuracy Class

LS-110 0.3kg 20kg OIML M2

VIII. Adjustment

1. Press the key to turn the scale on.

2. Once the LCD shows “8888” press the key sev-

LS-110 Manual

eral times until the inner code displays (~2680)

3. Press again.Thedisplaywillash“CAL”followed

by the required calibration weight (20kg).

4. Add the required weight. The display will show pass

and return to normal weighing mode.

5. Remove the weigh and press and hold the key to

turn the scale off. Calibration is complete!

IX. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries and ON/OFF lock

• Problem: Display will not stabilize

• Solution: Make sure the weight is stable on the

hook and not shaking or swinging

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment

X. Error Codes

1. OUTZ - Zero range has shifted. Perform calibration

adjustment. If the problem persists, the load cell may

be permanently damaged due to overloading.

2. EEEEE - Maximum capacity exceeded. Remove the

extra weight to avoid damaging the load cell.

3. LLLLL - Load cell has been overloaded.

4. UNST - The scale is unstable. Use the scale in a

more stable position

XI. Specications

LS-110

Max. Capacity 110lb / 50kg

Readability 0.2lb / 0.1kg

Min. Capacity 0.6lb / 0.3kg

Power 2 x CR2032

Dimensions 1.4 x 6.0 x 4.8 in. (hook extended)

Hook Dimensions Gap: 1.2in / Throat: 1.2in

Warranty 10 Year Limited Warranty

Tabla de contenidos

Manuales populares de Escala de otras marcas

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario