AWS AMW-500i Manual de usuario
American Weigh Scales, Inc.
User Manual
AMW-BENCH
Digital Tabletop Scale
AMW-500i
AMW-1000
g
ON/OFF
HoldModeTare
AMW-BENCH Manual
Thank you for purchasing the American Weigh AMW-
BENCH series digital tabletop scale. Please read
all operating instructions carefully before use. This
electronic scale is a precision instrument. With normal
care and proper treatment, it will provide years of
reliable service.
Never load the scale with more than the maximum
capacity. Overloading will permanently damage it!
Avoid any exposure to extreme heat or cold. Your
scale works better when operated at normal room
temperature. Always allow the scale to acclimate to
normal room temperature for at least one hour before
use. Give your scale sufcient warm up time. Usually
30-60 seconds before calibration to give the internal
components a chance to stabilize.
Keep your scale in a clean environment. Dust, dirt,
moisture, vibration, air currents and a close distance to
other electronic equipment can all cause an adverse
effect on the reliability and accuracy of your scale.
Handle with care. Gently apply all items to be weighed
onto tray top. Although this scale is designed to be
quite durable, try to avoid rough treatment as this may
permanently damage the internal sensor.
Avoid shaking, dropping or otherwise shocking the
scale. This is a precision instrument and must be
handled with extreme care.
Only operate the scale on a stable, vibration free
surface.
I. OPERATION
Place Scale on a horizontal at surface.
1. Press [ON/OFF] key.
2. Wait until "0.0” is displayed.
3. Put the object(s) on the weighing platform.
4. Using the [MODE] key, you can switch between the
weighing units.
II. TARE WEIGHING
1. Turn on scale as described above.
2. Place the "tare item" on the platform.
3. Press [TARE] and wait until "0.0" is displayed.
4. Add the "net-weight-item".
III. CALIBRATION
Calibration is NOT required before rst use. Only
calibrate if scale is not weighing properly.
**Make sure you use the correct calibration weight for
your scale or the calibration will not be accurate**
AMW-500i: 500g calibration weight
AMW-100: 2 (two) 500g calibration weights
a. AMW-500i Calibration Procedures
1. Press “On/Off” key to turn off the scale.
2. Press and hold the “On/Off” and “Mode” keys at the same
time until the display shows a random number. Release both
keys now.
3. Press the “On/Off” key once.
4. When the display reads “500 g”, place your 500g calibration
weight on the scale.
5. Press “On/Off” again. The display should read “PASS”.
You can now turn off your scale.
b. AMW-1000 Calibration Procedures
1. With the scale OFF, press and hold the “Tare” key until the
display shows a random number. Release the “Tare” key now.
3. Press the “Tare” key once. The scale will show “0.0”
4. Place your 500g calibration weight on the scale. The display
will show a random number.
5. Press “Tare” again. The display will show “500 g”
6. Place another 500g calibration weigh on the scale to make
a total of 1000 grams on the scale. The display will show a
random number.
6. Press “Tare” once more, the display should read “1000.0”.
You can now turn off your scale by holding the “Tare” key.
Please check the availability of weights with your scale
supplier.
IV. TROUBLESHOOTING
The primary reasons for inaccuracy or malfunction
are low batteries, incorrect calibration, overload or
operating on an unstable surface. Please keep this in
mind and maintain and operate your scale properly.
This scale is a precise instrument and must be
handled with the utmost care and caution.
[Display] Elimination of errors
Nothing, Battery-Symbol, [lo] or [88888]
Change the batteries.
[OL-d] The scale has been overloaded. You can
try recalibrating the scale as shown above.
[EEEEE] You are overloading the scale. Remove the
excessive load immediately!
[UNST] Use the scale in a more stable position
Specications
Model AMW-500i AMW-1000
Capacity 500g / 17.64oz / 16.08 ozt /
321.5dwt
1000g / 35.27oz / 32.15ozt /
643.1dwt
Resolution 0.1g / 0.01oz / 0.01ozt / 0.1dwt
Display 5 - Digit Backlit LCD
Calibration Weight
(not Included) 500g 2 (two) 500g
Platform Dimensions
(inches) 6 x 6 Stainless Steel
Scale Dimensions
(inches) 6.2 x 7.2 x 1.6
Power one 9V Battery (included) or AC-Adapter (sold seperate)
Gross Weight 1.63 lb
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Escala de AWS
AWS
AWS BLADE V2 BL2-50 Manual de usuario
AWS
AWS EPSILON EP-5KG Manual de usuario
AWS
AWS Bioweich USB Manual de usuario
AWS
AWS 330LPW Instrucciones de montaje
AWS
AWS AT Series Manual de usuario
AWS
AWS OM-200 Manual de usuario
AWS
AWS CP2-300 Manual de usuario
AWS
AWS AMW-13 Manual de usuario
AWS
AWS BS-100 Manual de usuario
AWS
AWS DK-5K Manual de usuario
AWS
AWS CITRON-5K Manual de usuario
AWS
AWS QUANTUM Instrucciones de montaje
AWS
AWS SR-1KG Manual de usuario
AWS
AWS NutriBalance-5000 Manual de usuario
AWS
AWS BLADE-50 Manual de usuario
AWS
AWS MiniCD MCD-100 Manual de usuario
AWS
AWS ScaleMate SM-200 Manual de usuario
AWS
AWS CARD-V2 Manual de usuario
AWS
AWS LB-1000 Manual de usuario
AWS
AWS AMW-Card120 Manual de usuario
