AWS Blade-100 Manual de usuario

BLADE-100 (100g x 0.01g)

BLADE-650 (650g x 0.1g)

BLADE-1KG (1000g x0.1g)

User Manual

BLADE Scale™

US Patent #D525,891

BLADE Scale

Thank you for purchasing the American Weigh Blade

Scale™. Please read all operating instructions carefully

before use. Scales are precision measuring devices and

should always be handled with proper care. To ensure years

of reliable service, keep these simple tips in mind:

• Do not exceed the scale’s maximum capacity.

Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales

perform best at normal room temperature. If

temperatures have changed dramatically, calibration

and adjustment may be necessary.

• Allow your scale to warm up for 30-60 seconds before

performing calibration and adjustment(if available).

• Store your scale in a clean, dry location. Dust, dirt,

and moisture can accumulate on the weighing

sensors and electronics causing inaccuracy or

malfunction.

• Avoid using your scale in close proximity to strong

radio wave emitting devices such as computers, cash

registers, and cordless phones.

• Alwaysweighonaatandlevelsurface,freefrom

vibrations and drafts. The corner of a room is usually

the most stable.

• Gently apply all items to be weighed. Do not drop

items onto the weighing platform.

• Avoid dropping your scale. The warranty does not

cover damage due to rough treatment or overload.

• Checkthebatteriesrstifyouarehavinganytrouble

with your scale. This simple step can remedy most

scale issues.

• Do not disassemble your scale. This product contains

no user serviceable parts.

ON/OFF

MODE

TARE

3.75"

0.8"

2.75"

I. Part List

1. Scale

2. Cover/Expansion Tray

3. AAA Batteries (x2)

II. Key Description

III. Battery Installation

1. Beforeusingthescaleforthersttime,check

the battery compartment and remove any plastic

insulation strips or packaging that may be in place to

prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the

positive and negative contacts are properly aligned.

Mode Key

Tare Key

Weight Indicator

ON/OFF Key

BLADE Scale

IV. Operation

1. Placethescaleonaat,levelsurfaceandpressthe

ON/OFF key to turn the scale on.

2. Once the start-up process completes and the scale

goes to zero you are ready to weigh.

3. Place the quantity to be weighed onto the weighing

platform.

4. Wait a couple seconds for the display to stabilize

before taking a weight reading.

V. Changing the Unit of Measure

1. Press the MODE key to change the scales displayed

unit of measure.

2. If the scale is turned off then back on, it will default

to the last unit used.

• BLADE-100 Units: g (gram) oz (ounce) ct (carat)

gn (grain)

• BLADE-650, BLADE-1KG Units: g (gram) oz

(ounce) ozt (troy ounce) dwt (pennyweight)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight

of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the

available capacity.

1. Place the empty container or vessel on the weighing

platform.

2. Press the TARE key once. The display will then

reset to zero. If the container is removed, it’s weight

will be displayed as a negative number.

3. Youmaynowllthecontainerwiththequantityto

be weighed. The display will show the net weight of

the contents.

4. To return to normal weight display (gross weight),

remove any items from the weighing platform and

press the TARE key again to re-zero the scale.

VII. Calibration

Calibration and adjustment are performed at the factory.

However, the weighing range can shift slightly during

shipping. Also, due to changes in local acceleration of gravity

around the world, adjustment is recommended when moving

the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale

and note the displayed value.

2. If the displayed value is not within acceptable

tolerance (see chart below), adjustment is required.

Model Acceptable

Tolerance (±)

Calibration

Weight

Recommended

Accuracy Class

BL-100 0.02g 100g OIML M2

BL-650 0.2g 500g OIML M2

BL-1KG 0.2g 500g OIML M2

VIII. Adjustment

1. Press and hold the MODE key until the display

shows “CAL”.

2. Press the MODEkeyagain.Thedisplaywillash

“CAL” followed by the calibration weight value (see

chart).

3. Place the calibration weight on the center of the

weighing platform. Make sure you are using the

correctweightforyourspecicmodel.

BLADE Scale

4. Once the weight is accepted, the display will show

“PASS” then return to normal operation.

IX. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries

• Problem: Displayedweightuctuatesrandomly

• Solution: Make sure your workspace is stable and

free of any air currents or vibration

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment

X. Error Codes

1. OUTZ - Zero range has shifted. Perform calibration

adjustment. If the problem persists, the load cell may

be permanently damaged due to overloading.

2. O-Ld - Maximum capacity exceeded. Remove the

extra weight to avoid damaging the load cell.

3. L - Batteries are low. Replace the batteries.

XI. Specications

BL-100

Max. Capacity 100g

Readability 0.01g

Min. Weight 0.03g

Power 2 x AAA

Dimensions 0.8 x 3.8 x 3.8”

Platform Dimensions 2.7 x 2.7”

BL-650 BL-1KG

Max. Capacity 650g 1000g

Readability 0.1g 0.1g

Min. Weight 0.2g 0.2g

Power 2 x AAA

Dimensions 0.8 x 3.8 x 3.8”

Platform Dimensions 2.7 x 2.7”

XII. Capacity/Readability Charts

BL-100

100g x 0.01g

3.528oz x 0.001oz

500ct x 0.05ct

1543gn x 0.1gn

BL-650 BL-1KG

650g x 0.1g

22.93oz x 0.01oz

20.90ozt x 0.01ozt

417.9dwt x 0.1dwt

1000g x 0.1g

35.27oz x 0.01oz

32.15ozt x 0.01ozt

643.1dwt x 0.1dwt

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Escala de otras marcas

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Fidelity Electronics

Fidelity Electronics G2e Manual de usuario