Anritsu 37 C Series Manual de usuario

MODEL

37XXXC

VECTOR NETWORK ANALYZER

OPERATION MANUAL

490 JARVIS DRIVE ·MORGAN HILL, CA 95037-2809 P/N: 10410-00226

REVISION: B

PRINTED: DECEMBER 2001

NOTICE

This manual and the 37XXXC Programming Manual,

along with other product literature, are provided on a

CD ROM (PN: 10920-00031) that is located in the in-

side-front cover pocket.

WARRANTY

The ANRITSU product(s) listed on the title page is (are) warranted against defects in materials and

workmanship for three years from the date of shipment.

ANRITSU’s obligation covers repairing or replacing products which prove to be defective during the

warranty period. Buyers shall prepay transportation charges for equipment returned to ANRITSU for

warranty repairs. Obligation is limited to the original purchaser. ANRITSU is not liable for consequential

damages.

LIMITATION OF WARRANTY

The foregoing warranty does not apply to ANRITSU connectors that have failed due to normal wear. Also,

the warranty does not apply to defects resulting from improper or inadequate maintenance by the Buyer,

unauthorized modification or misuse, or operation outside of the environmental specifications of the

product. No other warranty is expressed or implied, and the remedies provided herein are the Buyer’s sole

and exclusive remedies.

TRADEMARK ACKNOWLEDGEMENTS

V Connector and K Connector are registered trademarks of ANRITSU Company.

GPC-7 is a registered trademark of Amphenol Corporation.

ANACAT is a registered trademark of EEsof, Inc.

Ink Jet and Think Jet are registered trademarks of Hewlett-Packard Co.

MS-DOS is a registered trademark of Microsoft Corporation.

NOTICE

ANRITSU Company has prepared this manual for use by ANRITSU Company personnel and customers as

a guide for the proper installation, operation and maintenance of ANRITSU Company equipment and

computer programs. The drawings, specifications, and information contained herein are the property of

ANRITSU Company, and any unauthorized use or disclosure of these drawings, specifications, and

information is prohibited; they shall not be reproduced, copied, or used in whole or in part as the basis for

manufacture or sale of the equipment or software programs without the prior written consent of ANRITSU

Company.

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, ANRITSU Company uses the

following symbols to indicate safety-related information. For your own safety, please read the information

carefully BEFORE operating the equipment.

Symbols used in manuals

DANGER This indicates a very dangerous procedure that could result in serious

injury or death if not performed properly.

WARNING This indicates a hazardous procedure that could result in serious in-

jury or death if not performed properly.

CAUTION This indicates a hazardous procedure or danger that could result in

light-to-severe injury, or loss related to equipment malfunction, if

proper precautions are not taken.

Safety Symbols Used on Equipment and in Manuals

(Some or all of the following five symbols may or may not be used on all ANRITSU equipment. In addition,

there may be other labels attached to products that are not shown in the diagrams in this manual.)

The following safety symbols are used inside or on the equipment near operation locations to provide infor-

mation about safety items and operation precautions. Ensure that you clearly understand the meanings of

the symbols and take the necessary precautions BEFORE operating the equipment.

This indicates a prohibited operation. The prohibited operation is indi-

cated symbolically in or near the barred circle.

his indicates a compulsory safety precaution. The required operation is

indicated symbolically in or near the circle.

This indicates warning or caution. The contents are indicated symboli-

cally in or near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

37XXXC OM Safety-1

Safety-2 37XXXC OM

Always refer to the operation manual when working near locations at

which the alert mark, shown on the left, is attached. If the operation,

etc., is performed without heeding the advice in the operation manual,

there is a risk of personal injury. In addition, the equipment perfor-

mance may be reduced.

Moreover, this alert mark is sometimes used with other marks and de-

scriptions indicating other dangers.

WARNING

When supplying power to this equipment, connect the accessory 3-pin

power cord to a 3-pin grounded power outlet. If a grounded 3-pin outlet

is not available, use a conversion adapter and ground the green wire, or

connect the frame ground on the rear panel of the equipment to ground.

If power is supplied without grounding the equipment, there is a risk of

receiving a severe or fatal electric shock.

WARNING

This equipment can not be repaired by the operator. DO NOT attempt to

remove the equipment covers or to disassemble internal components.

Only qualified service technicians with a knowledge of electrical fire

and shock hazards should service this equipment. There are

high-voltage parts in this equipment presenting a risk of severe injury

or fatal electric shock to untrained personnel. In addition, there is a

risk of damage to precision components.

WARNING

Repair

For Safety

Use two or more people to lift and move this equipment, or use an

equipment cart. There is a risk of back injury, if this equipment is lifted

by one person.

WARNING

Table Of Contents

Chapter 1 — General Information

This chapter provides a general description of the ANRITSU Model 37XXXC Vector Network Ana-

lyzer System and its major units: network analyzer, test set, and frequency source. It also provides

descriptions for the precision component kits, and equipment options. Additionally, it contains the

listing of recommended test equipment.

Chapter 2 — Installation

This chapter provides instructions for performing an initial inspection, preparing the equipment for

use; setting up for operation over the IEEE-488.2 (GPIB) Bus, using a printer; and preparing the

units for storage and/or shipment. It also provides a listing of ANRITSU Customer Service Centers.

Chapter 3 — Network Analyzers, A Primer

This chapter provides an introduction to network analysis and the types of measurements that can

be made using them. It provides general and introductory description.

Chapter 4 — Front Panel Operation

This chapter describes the front panel controls and provides flow diagrams for the menus called up

using the front panel controls. It contains the following subchapters:

·Front Panel Control-Group Descriptions

·Calibration Keys and Indicators, Detailed Description

·Save/Recall Menu Key and Menus, Key Description and Menu Flow

·Measurement Keys and Menus, Key Descriptions and Menu Flow

·Channel Keys and Menu, Key Descriptions and Menu Flow

·Display Keys and Menus, Key Descriptions and Menu Flow

·Enhancement Keys and Menus, Key Descriptions and Menu Flow

·Hard Copy Keys and Menus, Key Descriptions and Menu Flow

·System State Keys and Menus, Key Descriptions and Menu Flow

·Markers/limits Keys and Menus, Key Descriptions and Menu Flow

·Disk Storage Interface, Detailed Description

Chapter 5 — Error And Status Messages

This chapter describes the type of error messages you may encounter during operation and provides a

tabular listing. This listing describes and defines the error types.

Chapter 6 — Data Displays

This chapter provides a detailed description of the various data displays. It describes the graph

types, frequency markers, measurement limit lines, status displays, and data display controls.

37XXXC OM i

Chapter 7 — Measurement Calibration

This chapter provides a discussion and tutorial on measurement calibration. It contains step-by-step

calibration procedures for the Standard (OSL), Offset-Short, TRM, and LRL/LRM methods. It also

has a procedure for calibrating using a sliding termination.

Chapter 8 — Measurements

This chapter discusses measurements with the 37XXXC VNA. It contains subchapters that provide a

detailed descriptions for Transmission and Reflection, Low Level and Gain, Group Delay, Active De-

vice, Multiple Source Control, Adapter Removal, Gain Compression, and Receiver Mode

measurements

Chapter 9 — Time Domain

This chapter describes the Option 2, Time Domain feature. It provides an operational procedure and

a flowchart of the time domain menus.

Chapter 10 — AutoCal

This chapter describes the Automatic Calibrator (AutoCal) feature and provides operational informa-

tion and procedures.

Chapter 11 — Operational Checkout Procedures, 371XXC

This chapter provides a procedure for operational checkout.

Chapter 12 — Operational Checkout Procedures; 372XXC, 373XXC

This chapter provides a procedure for operational checkout

Chapter 13 — Calibration Kits

This chapter provides a description and listing of components for the calibration kits.

Chapter 14 — Millimeter Wave System

This chapter contains description, operation, and checkout procedures for the millimeter wave mea-

surement capability that can be added to the 371XXC Vector Network Analyzer.

Chapter 15 — ME7808A Broadband Measurement System

This chapter contains description, operation, and checkout procedures for the optional broadband

measurement capability that can be added to the 37XXXC Vector Network Analyzer.

Appendix A — Front Panel Menus, Alphabetical Listing

This appendix shows all of the menus that are called up using the front panel controls. It provides a

replica of the menu and descriptive text for all of the various menu choices. The listing is alphabeti-

cal by the menu call letters mentioned and/or illustrated in Chapter 4.

Appendix B — Model 37XXXC VNA Rear Panel Connectors

This appendix describes the rear panel connectors. It also provides pinout listing.

Appendix C — Performance Specifications

This appendix contains the Technical Data Sheet, part number 11410-00247, which provides perfor-

mance specifications.

Index

ii 37XXXC OM

Table of Contents

Chapter 1 General Information ·····················1-1

1-1 SCOPE OF MANUAL ...........................1-3

1-2 INTRODUCTION .............................1-3

1-3 IDENTIFICATION NUMBER .......................1-3

1-4 ONLINE MANUALS............................1-3

1-5 SYSTEM DESCRIPTION .........................1-3

371XXC ...................................1-3

372XXC ...................................1-4

373XXC ...................................1-4

1-6 MILLIMETER WAVE MEASUREMENTS ................1-5

1-7 PRECISION COMPONENT KITS.....................1-5

Model 3650 SMA/3.5 mm Calibration Kit .................1-5

Model 3651 GPC–7 Calibration Kit ....................1-6

Model 3652 K Connector Calibration Kit.................1-7

Model 3653 Type N Calibration Kit ....................1-8

Model 3654B V Connector® Calibration Kit...............1-10

Model 3666 3.5 m Verification Kit ....................1-10

Model 3667 GPC–7 Verification Kit ...................1-11

Model 3668 K Connector®Verification Kit ...............1-12

Model 3669/3669B V Connector®Verification Kits ...........1-13

1-8 OPTIONS .................................1-14

1-9 PERFORMANCE SPECIFICATIONS ..................1-14

1-10 PREVENTIVE MAINTENANCE.....................1-14

Chapter 2 Installation ··························2-1

2-1 INTRODUCTION .............................2-3

2-2 INITIAL INSPECTION ..........................2-3

2-3 PREPARATION FOR USE.........................2-3

2-4 GPIB SETUP ................................2-4

Interface Connector ............................2-4

37XXXC OM iii

Cable Length Restrictions .........................2-4

2-5 SYSTEM GPIB INTERCONNECTION ..................2-5

GPIB Interface to an External Plotter...................2-5

GPIB Addresses ..............................2-5

2-6 EXTERNAL MONITOR CONNECTOR ..................2-5

2-7 RACK MOUNT ...............................2-5

2-8 STORAGE AND/OR SHIPMENT .....................2-8

Preparation for Storage ..........................2-8

Preparation for Shipment .........................2-8

2-9 SERVICE CENTERS............................2-8

Chapter 3 Network Analyzers, A Primer ················3-1

3-1 INTRODUCTION .............................3-3

3-2 GENERAL DESCRIPTION ........................3-3

Source Module ...............................3-4

Test Set Module...............................3-4

Analyzer Module ..............................3-4

3-3 NETWORK ANALYZERS .........................3-5

Chapter 4 Front Panel Operation ····················4-1

4-1 INTRODUCTION .............................4-3

4-2 KEY-GROUPS ...............................4-3

4-3 CALIBRATION KEY-GROUP ......................4-10

4-4 SAVE/RECALL MENU KEY .......................4-21

4-5 MEASUREMENT KEY-GROUP .....................4-22

4-6 CHANNELS KEY-GROUP ........................4-25

4-7 DISPLAY KEY-GROUP..........................4-26

4-8 ENHANCEMENT KEY-GROUP .....................4-30

4-9 HARD COPY KEY-GROUP........................4-32

4-10 SYSTEM STATE KEY-GROUP......................4-34

4-11 MARKERS/LIMITS KEY-GROUP ....................4-37

4-12 DISK STORAGE INTERFACE .....................4-41

Disk Format ...............................4-41

Disk Files .................................4-41

Disk File Output Device .........................4-42

iv 37XXXC OM

Tabla de contenidos

Otros manuales de Instrumento de medición de Anritsu

Anritsu

Anritsu PIM Master MW82119A Manual de usuario

Anritsu

Anritsu BTS Master Manual de usuario

Anritsu

Anritsu MP1590B Manual de usuario

Anritsu

Anritsu Field Master Pro MS2090A Manual de usuario

Anritsu

Anritsu MP1763C Manual de usuario

Anritsu

Anritsu MS2840A-040 Manual de usuario

Anritsu

Anritsu MS2720 A Series Manual de usuario

Anritsu

Anritsu MS2690A Manual de usuario

Anritsu

Anritsu Site Master S331C Manual de usuario

Anritsu

Anritsu ShockLine MS46121A Series Manual del propietario

Anritsu

Anritsu Site Master Manual de usuario

Anritsu

Anritsu IQ Fiber Master Manual de usuario

Anritsu

Anritsu VectorStar ME7838E4 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Anritsu

Anritsu VectorStar ME7838 4X Series Manual de usuario

Anritsu

Anritsu MP1800A Manual de usuario

Anritsu

Anritsu VectorStar ME7838A Manual de usuario

Anritsu

Anritsu Spectrum Master MS2721B Manual de usuario

Anritsu

Anritsu MS2681A Manual de usuario

Anritsu

Anritsu Sire Master S331D Manual de usuario

Anritsu

Anritsu Network Master MU909020A Manual de usuario

Anritsu

Anritsu MS2830A Manual de usuario

Anritsu

Anritsu MS2830A Manual de usuario

Anritsu

Anritsu MS2690A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario