Agilent Technologies B2901 Manual de usuario

Agilent B2901/02/11/12A Precision Source/Measure Unit

How to source continuous pulses without any measurement

This material shows how to setup the instrument to source continuous pulses without any measurement using the

B2901/02/11/12A, through example to source 2 V continuous pulses with the timing parameters such as 300 us pulse

delay, 200 us pulse width and 500 us source trigger period.

Figure 1 shows the timing chart for the continuous pulse source.

Figure 1. Timing chart for the continuous pulse source

It is required to abort the instrument when you’d like to stop sourcing continuous pulses.

This material also shows how to abort the instrument to stop continuous pulses.

Setting up the pulse condition

Step 1. Press to edit the source function, and then select to set the source function to the voltage

source.

TIMER TriggerOutput ON

Source Value

Output

Off State

V or I

Time

TPD TPW

Pulse

Peak Value

TPD TPW TPD TPW

TSP TSP TSP

TPW : Pulse WidthTPD : Pulse Delay TSP : Source Trigger Period

(1) Press Mode (2) Press VOLTS (V)

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 2. Press to edit the source value, and then enter 0 V to set the source value to 0 V.

Step 3. Press to edit the limit value, and then enter 10 mA to set the limit value to 10 mA.

Step 4. Press to change the keys shown in Assist keys, and then press to show Pulse Sub-Panel.

Step 5. Press , then press to set the pulse source ON. After turning on the pulse source, you can

see Source Shape which shows the pulse source mode.

(1) Press Source (2) Enter Source Value

(1) Press Limit (2) Enter Limit Value

(1) Press Show Pulse (2) Pulse Sub-Panel appears

(1) Press ON Source Shape

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 6. Rotate to select Channel 1 Pulse Parameters and set them up as below.

(Peak: 2 V, Delay: 300 us, Width: 200 us)

Step 7. Press to show Trigger Sub-Panel.

Step 8. Press to edit the trigger type, and then select to set the trigger type to MANUAL.

(1) Press Show Trigger (2) Trigger Sub-Panel appears

(2) Press MANUAL(1) Press

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 9. Rotate to select the source trigger period and press to edit it. Then enter 500 us to set the

source trigger period to 500 us.

Step 10. Rotate to select the source trigger source and press to edit it. Then press to set

the source trigger source to TIMER.

Step 11. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 12. Press and then press to open Trigger Configuration dialogue.

(2) Enter Source Trigger Period(1) Rotate and press

Source Trigger Period

to edit

(2) Press TIMER(1) Rotate and press

Source Trigger Source

to edit

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Config

Agilent B2901/02/11/12A Precision Source/Measure Unit

Step 13. Press and select to specify the layer, the trigger parameters of which are configured.

Step 14. Rotate to select the arm count and press to edit it. Then press to set the arm

count to INFINITY.

Step 15. Press to make the modification effective.

(2) Press ARM(1) Press

(2) Press INF.

(1) Rotate and press

ARM Count

to edit

(1) Press OK to make the modification effective

Agilent B2901/02/11/12A Precision Source/Measure Unit

Starting sourcing the continuous pulses

Step 16. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 17. Press , , , and then press to start sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Initiate

(3) Press Trans.

(4) Press Ch 1

Agilent B2901/02/11/12A Precision Source/Measure Unit

Stopping sourcing the continuous pulses

Step 18. If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Step 19. Press , , , and then press to stop sourcing the

continuous pulses.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Trigger

(2) Press Abort

(3) Press Trans.

(4) Press Ch 1

Otros manuales para B2901

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies 4155C Manual de instalación

Agilent Technologies

Agilent Technologies 85051B Manual

Agilent Technologies

Agilent Technologies PSA Series Manual de usuario

Agilent Technologies

Agilent Technologies ESA Series Manual

Agilent Technologies

Agilent Technologies 4338B Manual de usuario

Agilent Technologies

Agilent Technologies U2722A Manual de usuario

Agilent Technologies

Agilent Technologies E4991A Manual de usuario

Agilent Technologies

Agilent Technologies 100 Manual de usuario

Agilent Technologies

Agilent Technologies 71612 Manual de usuario

Agilent Technologies

Agilent Technologies N2771A Manual de usuario

Agilent Technologies

Agilent Technologies WireScope 350 Manual de usuario

Agilent Technologies

Agilent Technologies MXA Series Manual de instalación y operación

Agilent Technologies

Agilent Technologies 8560 E-Series Manual de usuario

Agilent Technologies

Agilent Technologies E8356A Manual de instalación y operación

Agilent Technologies

Agilent Technologies 1290 Infinity II 2D-LC Solution Manual de usuario

Agilent Technologies

Agilent Technologies E4445A PSA Series Guía de inicio rápido

Agilent Technologies

Agilent Technologies Flow Tracker 1000 Series Manual de operación

Agilent Technologies

Agilent Technologies E4402/7B Manual

Agilent Technologies

Agilent Technologies E8362A Manual de usuario

Agilent Technologies

Agilent Technologies 11867A? Manual de servicio

Agilent Technologies

Agilent Technologies X Series Manual de usuario

Agilent Technologies

Agilent Technologies 8590L Manual de usuario

Agilent Technologies

Agilent Technologies 3200D Manual de usuario

Agilent Technologies

Agilent Technologies N1913a Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario